BiSoft1131 - Binar Elektronik

2005-02-07
PAGE 1 (3)
BiSoft1131
UPDATES AND RELEASE NOTES
ver 1.21.08 RELEASE DATE: 2005-02-07
Updates
• Supports more than 25 IP addresses.
• Problems causing timers to hang after 24 days fixed.
Software part of the release:
SoftControl: ver 2.3.56c
BiFas lib: ver 1.13
Standard lib: ver 1.21.05
Help system: ver 1.11
NetEdit: ver 2.01.04
ver 1.21.06 RELEASE DATE: 2004-02-10
Updates
• Release notes accessible from the Start menu.
• The On-line mode was not accessible if the Seek dialog was open. Fixed.
• The following functions now work properly:
E_TIME_TO_DINT, E_DINT_TO_TIME, E_ADD, E_MAX, E_MIN, TON,
E_TON, TOF, E_TOF, TP and E_TP.
• String handling improved. However, be cautious not to use strings longer
than 32 characters in length! If done, the variable stored in the next
memory position will be overwritten.
• Help System updated (now version 1.11).
• NetEdit updated (now version 2.01.04).
• From now on the standard library gets the same version number as the BiSoft1131 release.
• BiFas Library updated (now version 1.13).
• The following function blocks added:
MotionMultiAxes Multi axes motion control block for one to five axes.
MotionSingleAxis Single axis motion with possibility to get feedback from an extern encoder.
AnalogServoInit Initiates a servo drive with an analog input –10V to +10V via BiEnc.
AnalogServoPos Positions a servo drive with an analog input –10V to +10V via BiEnc.
CamTableGenerat Generates a CAM table (replacement for older block “Profilegenerator”).
CamTableInsParam Used for entering parameters into the parameter list “mdParamList”.
CamTableInsPoint Used for entering positioning points into the point list “mdPointList”.
CamTableSeek Used for finding the table positioning point closest to the actual position.
CamTableMotion Reads CAM tables and sends positioning data to the servo every 5 ms.
FilterFirAdj Adjustable FIR filter.
RotationCheck RotationCheck
BiDispSend Sends data to the industrial display BiDisp via a BRSC CAN-Serial converter.
• The following function blocks are updated:
BIMError
BIMInit
FiterFir
SEWMdsPos
SEWMdvPos
SEWDriver
OneAxisMotion
SEWMdsPos
SEWMdvPos
SewDriver
Alarmhandler
Output for communication alarm added
No longer blocks re-initiation
Causes less system load
Can now be calibrated in simulated mode also.
Sensor resolution can be defined. EN and ENO pins are removed.
Alarms no longer freezes the Is-position.
An output is set if alarm exists.
Software part of the release:
SoftControl: ver 2.3.56c
BiFas lib: ver 1.13
Standard lib: ver 1.21.05
Help system: ver 1.11
NetEdit: ver 2.01.04

2005-02-07
PAGE 2 (3)
BiSoft1131
UPDATES AND RELEASE NOTES
ver 1.21.04 RELEASE DATE: 2002-08-30
Updates
• Improved error handling in on-line mode.
• Improved program download procedure.
• Improved serial communication.
• NetEdit updated (now version 2.0.4.4).
• Editing an existing node will no longer create a new one.
• Now runs on Windows2000.
• Help System updated (now version 1.10).
• Standard Library updated (now version 1.28).
• Function blocks for the following new BRIOS2 terminals added:
750-346 Fieldbus coupler DeviceNet, (Economy)
750-411 2-Channel Digital input module, 24VDC, 0.2ms
750-419 2-Channel Digital input module, 24VDC, 3.0ms, with diagnostics
750-423 4-Channel Digital input module, 24VAC/DC, 50ms, with jumper contacts
750-425 2-Channel Digital input module, NAMUR proximity switch
750-430 8-Channel Digital input module, 24VDC, 3.0ms
750-431 8-Channel Digital input module, 24VDC, 0.2ms
750-472 2-Channel Analog input module, 0-20mA, 16-bit single-ended
750-474 2-Channel Analog input module, 4-20mA, 16-bit single-ended
750-476 2-Channel Analog input module, 0-10V, 16-bit single-ended
750-478 2-Channel Analog input module, +-10V, 16-bit single-ended
750-491 1-Channel Analog input module, Resistor bridge
750-507 2-Channel Digital output module, 24VDC, 2.0A, short-circuit protected, with diagnostics
750-517 2-Channel Relay output module, 230VAC, 300VDC, 1.0A, changeover contacts
750-522 2-Channel Digital output module, 230VAC, with solid state relay 3A for 30 sec
750-530 8-Channel Digital output module, 24VDC, 0.5A, short-circuit protected
750-621 Seperation module with power jumper contacts
750-637 Incremental encoder interface, with cam outputs
• Boundry checks added to the following functions:
TAN, ASIN, ACOS, LN LOG and SQRT
TAN(-π/2 (±10 -6 )) = 0; TAN(π/2 (±10 -6 )) = 0
ACOS(1) = 0
ASIN(1) = π/2
LN(

2005-02-07
PAGE 3 (3)
BiSoft1131
UPDATES AND RELEASE NOTES
ver 1.20.26 RELEASE DATE: 2001-12-13
Updates
• A database repair tool has been included.
• Help System updated (version 1.09).
• BiFas Library version 1.11 now included.
• Applicable BiFas function blocks are updated with the parameter
“ParServiceId”. This makes it possible to choose whether servo
parameters are written to the RAM or the EEPROM memory area of the
MOVIDRIVE servo amplifier.
• A new version of NetEdit is included.
(directory path to NetEdit now stored in the Windows System register)
• Problems associated with setting Normal Task execution interval fixed.
• Roll-over problems in the TON, TOF, E_TON and E_TOF functions fixed.
Software part of the release:
SoftControl: ver 2.3.56c
BiFas lib: ver 1.11
Standard lib: ver 1.26
Help system: ver 1.09
NetEdit: ver 2.0.4.2
ver 1.20.24 RELEASE DATE: 2001-09-21
Updates
• This version fixes problems which could occur in the On-line driver. Large
application files now are properly downloaded and switched in.
• The Senitel hardware protection device is no longer needed.
• New low-level functions in the IO_Misc Library.
Software part of the release:
SoftControl: ver 2.3.56c
BiFas lib: ver 1.10
Standard lib: ver 1.24
Help system: ver 1.07
NetEdit: ver -