Description Aquatower 2000 1/2" wall mounted profile ... - GROHE

27017 000 Page 1 

Description 

Aquatower 2000 1/2" 

wall mounted 

profile: 

eloxal aluminium profile 

stand alone shower bar with glider and 

handshower 

Shelf behind the panel 

showers: 

1 handshower Relexa Cosmopolitan Dual 1/2" (28 126) 

3 large adjustable side showers (30°) 

all showers are equipped with SpeedClean 

Relexaflex hose 1750 mm 1/2" x 1/2" (28 154 000) 

fittings: 

pre-assembled installation unit 

1 thermostat 1/2" with increased flow rate 

1 Aquadimmer 1/2" to select 

hand- and/or side showers 

direct installation at included elbow connections 

colour: 

Aluminium profile 

fittings, showers, shower bar and shower hose chrome 

Min. recommended pressure 1.0 bar 

Max. pressure differential 5:1 

shower system 

wall mounted 

with Relexa Cosmopolitan handshower 

Grohe UK Ltd | Tel.: +44 871 200 3414 | email: info@grohe.co.uk | www.grohe.co.uk | 

Address: Blays House, Wick Road, Englefield Green, Egham, Surrey, UK, TW20 0HJ

27017 000 Page 2 

Dimensional drawing 



27017 000 Page 3 

Flow chart 



27017 000 Page 4 

Explosional drawing 



27017 000 Page 5 

Part list 

Pos. Description Order No Unit 

1 strainer 07002 00M 2 

2 Sliding piece 12353 000 1 

3 Nipple 47424 000 1 

3.1 Non-return valve 08565 000 1 

4 Escutcheon 09532 000 1 

5 Installation tool 09813 000 1 

6 Spray faceplate 45244 XX0 1 

7 Handle 47542 IP0 1 

7.1 Cover Cap 02490 P0M 2 

8 Sleeve 04952 000 1 

9 Thermo-element 47217 000 1 

9.1 Stop ring and regulating nut 47300 000 1 

9.1.1 Fixing clamp 05744 00M 2 

9.2 O-Ring Ø21 x Ø2 05999 00M 10 

9.3 O-Ring Ø24 x Ø2 01196 00M 10 

10 Thermostat seat 01460 000 1 

11 Handle 47374 IP0 1 

11.1 Cover Cap 02490 P0M 2 

12 Sleeve 02730 000 1 

13 Aquadimmer 47364 000 1 

14 Non-return valve 1/2" 14116 00M 2 

14.1 Repl. kit f. seal 47303 000 2 

14.1.1 strainer 02990 00M 2 

Special accessories: 

15 Socket Spanner 19070 000 1 



27017 000 Page 6 

Maintenance instructions 

Shut off hot and cold water supply! 

Please perform disassembly in specified order. 

Thermoelement 

1. Lever out cap. 

2. Loosen screw. 

3. Pull off temperature selection handle. 

4. Remove clip. 

5. Pull off stop ring. 

6. Pull off regulating nut with overload unit. 

7. Unscrew and remove thermoelement using a 22mm 

open-ended spanner. 

Aquadimmer 


2. Unscrew and remove screw, pull off shut-off handle. 

3. Remove splined adapter and stop. 

4. Unscrew and remove Aquadimmer using a 19mm openended 

spanner. 

Observe the correct installation position. 

1. The dissimilar pins (1) and (2) must engage in the 

corresponding holes in the race. 

2. Fit stop with marking pointing downwards, markings (3) 

and (4) align. 

3. Fit splined adapter, the faces coincide in only one 

position. 

4. Turn splined adapter so that the lug points to the right. 



27017 000 Page 7 

Non-return valve 


2. Push shower rail slider off shower rail. 

3. Screw off shower rail. 

4. Unscrew and remove screw. 

5. Lever out caps (A2) and (B2). 

6. Unscrew and remove screws (A1) and (B1) and pull off 

shut-off handle (A) and temperature selection handle (B). 

7. Lever off escutcheons and unscrew retaining rings using 

installation tool. 

8. Pull off wall plate. 

9. Unscrew and remove non-return valve using a 17mm 

socket spanner. 

Sideshower 

1. Unscrew and remove screw using a screwdriver. 

2. Detach complete spray face plate. 

3. Pull off housing. 

4. Pull off washer by pressing in the ball. 

5. Remove ball. 

6. Pull out non-return valve using pliers. 

When fitting the washer, the ball must be pressed slightly 

into the housing. 

Assemble in reverse order. 

Readjustment is necessary after each maintenance operation on the thermostatic cartridge. 



27017 000 Page 8 

Temperature adjustment 

1. Open the cold and hot water supply. 

2. Open shut-off handle to hand shower position and 

measure temperature of the water using a thermometer. 

3. Turn temperature selection handle until the water 

temperature reaches 38 °C. 


5. Hold temperature selection handle in this position and 

remove screw. 

6. Pull off temperature selection handle and refit so that the 

38°C marking on the wall plate aligns with the marking on 

the handle. 

7. Screw in screw and fit cap. 

The function of the SpeedClean nozzles is guaranteed for a period of five years. 

Simply rub SpeedClean nozzles in order to remove limescale deposits from roses of hand, overhead and side sprays. 

Prevention of frost damage 

When the domestic water system is drained, the thermostats must be drained separately since non-return valves are 

installed in the hot and cold water connections. For this purpose, the shower system must be removed from the wall.

Description Aquatower 2000 1/2" wall mounted profile ... - GROHE

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?