Manual Racer Precision-Speed Saw

More documents

Recommendations

Info

TM forward feed speed. Overload indicator (2) continually lit: The electric power tool is overloaded or jammed - the electric power tool cuts out. In this event, switch the electric power tool off and allow it to cool down before using it again. 7.5 Use Warning! Always begin by making a test cut in a left-over piece. • Firmly clamp small wooden pieces before commencing work. Never hold them in your hand. • Fully observe the safety regulations! Wear safety glasses! • Adjust the cutting depth and rotation speed. • Pick up the electric power tool and make sure that none of the ventilation openings are covered. • Switch on the electric power tool and wait for several seconds until the tool insert has attained its full rotation speed. • The waste piece should be on the right or left side of the electric power tool, so that the wide part of the supporting table rests on its entire surface. • The base plate must always rest flat on the workpiece. • Press the release button (7) and slowly push the tool insert into the workpiece or, if necessary, plunge it. • Push the electric power tool forwards through the workpiece. Never move it backwards! • Apply only a gentle force to the electric power tool when working. • If sawing along a marked line, lead the electric power tool along the appropriate groove. • If the overload indicator (2) flashes, reduce your speed. • If the electric power tool stops and the overload indicator (2) is lit continuously, then the overload protection of the electric power tool has responded. Reason: You were moving forward too quickly or have encountered an obstacle in the workpiece. In this case, switch off the electric power tool and inspect the workpiece. Move forward at a slower speed. 7.6 Line cuts (Figure 7) You can follow a drawn line with the help of the indicator marks (a), at the front and rear of the safety guard. For precise work, the relationship between the saw cut and a marked indicator line must be established using a test piece. The ideal positioning of the saw cuts must then be achieved by adjusting the indicator line to the target line. 7.7 Working with large workpieces When working with large workpieces or cutting straight edges: • Use fastening clamps to tighten a board or border onto the workpiece as an auxiliary stop. • Guide the left-hand side of the base plate along the auxiliary stop. 7.8 Plunge cuts (Figure 4) Note: Some very hard materials are not suitable for plunge cuts. Put the base plate on the workpiece. Make sure that the rear lateral depth marking is at the height of the beginning of the cut. Switch on the electric power tool and allow a couple of seconds to pass until the tool insert reaches its full speed. Then plunge the tool insert, slowly but with some pressure. Push the electric power tool forwards through the workpiece. When you reach the end of the cut, switch off the electric power tool and pull it out of the workpiece. 7.9 Cutting tiles Adhesive tape or insulation tape on the workpiece makes the work easier and helps to prevent it from getting scratched. 8. Cleaning and MAINTENANCE Warning! Pull out the power plug before any cleaning work. Cleaning • Keep safety devices, ventilation openings and the motor housing as free as possible from dirt and dust. Rub the electric power tool with a clean cloth or blow over it with low pressure compressed air. • We recommend that you clean your electric power tool immediately after each use. 28
EN • Clean the electric power tool regularly with a damp cloth and somewhat soft soap. Do not use any cleaning or solvent materials; these can attack the device's plastic components. Make sure that no water can get inside the electric power tool. Carbon brushes In the event of excessive sparking, allow a qualified person to examine the carbon brushes. Attention! The carbon brushes may only be exchanged by a qualified person. Maintenance There are no further parts requiring maintenance inside the electric power tool. 9. Repair and ordering of spare parts Exchanging the power cable If the power cable of this electric power tool is damaged, it must be replaced by the manufacturer, its customer services department or a similarly qualified person to avoid danger. Spare parts/Accessories Spare parts and accessories can be ordered through our web shop: www.batavia.eu EC-Declaration of conformity We, the Batavia GmbH, Blankenstein 180, NL-7943PE Meppel, declare by our own responsibility that the product <strong>Precision</strong> Circular <strong>Saw</strong>, Item-No 7060453, Model Nr. BT-CS006 is according to the basic requirements, which are defined in the European Directives Electromagnetic Compatibility (EMC), 2006/42/EC (Machinery), 2006/95/EC Low Voltage Directive (LVD) and their amendments. For the evaluation of conformity, the following harmonized standards were consulted: EN 60745-1: 2009+A11, EN 60745-2-5: 2010, EN 55014-1: 2006+A1 EN55014-2: 1997+A1+A2, EN 61000-3-2: 2006+A1+A2, EN 61000-3-3: 2008 Meppel, 01 June 2011 Meino Seinen, QA Representative Batavia GmbH, Blankenstein 180, 7943 PE Meppel, Netherlands 10. Disposal and recycling Do not dispose of electric power tools with domestic refuse. The electric power tool is shipped in packaging to reduce transport damage. This packaging is a raw material and as such can either be reused or can be fed back into the raw material cycle. The electric power tool and its accessories are made from various materials such as metals and plastics. Take defective components to a special refuse collection point. Ask about these at your specialist shop or local council. The product and the user manual may be subject to changes. Technical data may be changed without prior notice. 29
Page 1 and 2: TM Bedienungsanleitung (Original) O
Page 3 and 4: DE 8 7 1 9 14 10 12 11a 11b 2 5  
Page 5 and 6: DE Das Eindringen von Wasser in ein
Page 7 and 8: DE Ein Rückschlag ist die Folge ei
Page 9 and 10: DE Einsatzwerkzeug kann in Kontakt
Page 11 and 12: DE 8. Arbeiten Sie nur im rechten W
Page 13 and 14: DE • Überlasten Sie das Elektrow
Page 15 and 16: DE • Kleine Holzteile vor der Bea
Page 17 and 18: EN 8 7 1 9 14 10 12 11a 11b 2 5  
Page 19 and 20: EN e) When operating a power tool o
Page 21 and 22: EN f) Before sawing, firmly tighten
Page 23 and 24: EN c) Avoid the area in front of an
Page 25 and 26: EN 3. COMPONENT description and sco
Page 27: EN • A wood underlay can be used
Page 31 and 32: NL 1. VERKLARING VAN DE SYMBOLEN WA
Page 33 and 34: NL f) Zorg dat snij- en zaagwerktui
Page 35 and 36: NL maximale toerental. Accessoires
Page 37 and 38: NL Behandeling en opslag Schijven d
Page 39 and 40: NL 5. Technische gegevens Stroomaan
Page 41 and 42: NL Let op! Gebruik de machine altij
Page 43 and 44: NL Het product en de gebruiksaanwij
Page 45 and 46: FR 1. Explication des symboles AVER
Page 47 and 48: FR électrique. Les appareils élec
Page 49 and 50: FR c) Lors de coupes « plongeantes
Page 51 and 52: FR e) N’utilisez pas de lames de
Page 53 and 54: FR Avertissement! Cet appareil éle
Page 55 and 56: FR Remarque: Laissez tout d’abord
Page 57 and 58: FR Posez la plaque de base sur la p
Page 59 and 60: 2 YEAR WARRANTY Modelnr. BT-CS006 A

Manual Racer Precision-Speed Saw

Create successful ePaper yourself

Delete template?

Save as template?