FOCUS TRAVEL SYSTEM - Babylove

FOCUS TRAVEL SYSTEM 

Suitable for use with Babylove Snap ‘n Go model BL620 Infant Carrier and 

Babylove Bassinette (both sold separately). 

Thank you for purchasing this quality Babylove product from our exclusive range of baby products. 

We are confident that you will appreciate its many highlights including durability and reliability. Your 

new product has been manufactured to comply with the Australian Standard AS/NZS 2088:2000 

and comes with a 12 month warranty (receipt required). Please keep this instruction manual for future 

reference. 

Distributed by Nursery Elegance Pty Ltd 

ACN 122 443 387 

Unit 10, 339 Williamstown Road Port Melbourne VIC 3207, Australia 

PHONE 1300 131 477 

WEB: www.babylove.com.au 

EMAIL: info@Babylove.com.au 

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE 

20 

series ES9100 

4800058

NOTES 

IMPORTANT: RETAIN FOR FUTURE REFERENCE. 

READ THESE INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE. 

THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL. 

WARNINGS 

. 

Do not leave children unattended. 

. 

Follow the manufacturer’s instructions. 

. 

Ensure your child is secured with a correctly adjusted safety harness. 

. 

Do not carry additional children or bags on the stroller. 

. 

Do not allow children to stand on the seat, the stroller may tip over. 

. 

Do not hang bags or goods from the handle as this could cause the stroller to tip over. 

. 

Do not place more than 4kg in the basket, or 1kg in the canopy pocket (if supplied). 

. 

The weight of the child using this product should not exceed 17kg. 

. 

Do not use accessories other than those supplied and approved by Babylove. 

. 

When making adjustments to the stroller, ensure that your child’s body is clear of any 

moving parts on the stroller, otherwise they may be injured. 

. 

Always apply all of the brakes when parking the stroller. The stroller may roll away even if 

left unattended for a few moments. 

. 

Use the tether strap to prevent the stroller from rolling away. 

. 

Check that all safety locks are engaged before placing a child in the stroller. 

. 

Always raise the leg support to its highest position when transporting a baby. This will 

reduce the risk of the baby falling out through the front of the stroller. 

. 

Remove the child from the stroller before going up or down stairs and escalators. 

. 

To prevent the risk of the stroller catching fire, do not park it near an exposed heat source 

such as a radiator, an open fire or a barbecue, etc. 

. 

Do not run while using this product. 

. 

Do not lift the stroller by the bumper bar. It may disengage. 

. 

Always lock the front swivel wheel when on uneven surfaces to minimize wheel wobble. 

RECOMMENDATION 

Some strollers have backrests adjustable between an upright and reclined position. The upright 

positions are not suitable for use with children less than six months old. As a guide, the lowest 

recline position should be used to transport babies, the backrest can be adjusted to a more 

upright position as the child grows older and is able to support its head without assistance. 

SAFETY WARNING 

The sun is very strong. DO NOT LEAVE YOUR CHILD EXPOSED TO THE SUN. The canopy or 

hood on this product will not give your child total protection from the harmful rays of the sun. 

THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE. 

02 www.babylove.com.au 

www.babylove.com.au 

19

CLEANING 

. 

To clean vinyl and metal parts wipe with a clean wet cloth and a mild soap and water 

solution. 

. 

To clean woven fabric use upholstery cleaner such as normally used on furniture or a 

mild soap and water solution. Allow fabrics to air dry, out of direct sunlight. 

. 

Never clean with abrasive, ammonia based, bleach based or spirit type cleaners. 

CARE & MAINTENANCE 

. 

Check the main components and other parts operate freely and are secure. Check 

regularly for wear & tear, loose fasteners and damage. Tighten any loose fasteners. 

Replace any worn or damaged parts immediately using only Babylove approved parts. 

. 

Moving parts may require occasional lubrication with a dry lubricant or a silicon based 

spray lubricant. This will help avoid squeaks. 

. 

Exposure to direct sunlight will fade most fabrics over time. To limit the effect of UV 

fading, avoid leaving stroller in direct sunlight where practicable. 

PARTS LIST 

A 1 - Frame 

B 1 - Seat 

C 1 - Canopy 

2 - Rear Wheels 

1 - Rear Brake Assemblyear Brake Assembly 

1 - Armbar 

A 

D 1 - Bootcover 

E 2 - Infant Carrier Adaptors 

C 

B 

D 

MODEL VARIATIONS 

. 

Not all models will have features such as rain covers, canopy windows, etc. 

. 

Note that the fabric patterns and colours pictured on the stroller in this instruction 

manual may vary from that of the product that you have purchased. 

E 



03

1. TO OPEN THE FRAME 

20. TO INSTALL THE ‘SNAP N GO’ INFANT CARRIER (sold separately) Cont’d 

A 

B 

Stand the frame upright and release the 

frame lock. 

Hold the frame handle with the left 

hand, then with the right hand, pull the 

main handle upwards until the frame is 

fully extended. 

C Check the frame is fully extended by 

lightly pressing down on the main 

handle, the frame should not collapse. 

A 

K 

The adaptors can remain engaged to 

the frame while using the Infant Carrier. 

They must be removed to use the 

Bassinette or Stroller Seat. 

TO REMOVE THE ADAPTORS 

L 

With one hand, press in and hold the 

RED button. At the same time with the 

other hand, slide the adaptor up. Store 

adaptors away for future use. 

K 

L 

CB 

L 

C 



17

20. TO INSTALL THE ‘SNAP N GO’ INFANT CARRIER (sold separately) Cont’d 

2. TO FIT AND REMOVE THE REAR WHEEL ASSEMBLY 

B 

Pull up on each Infant Carrier adaptor to make 

sure they are engaged. 

A 

Slide the rear wheel assembly onto the rear leg tubes 

with the RED brakes levers facing out. 

C 

D 

To engage the Infant Carrier into the adaptors, 

position the Infant Carrier locking mechanisms 

located under the handle on either side, over 

the adaptors and push down. 

Make sure the Infant Carrier is locked into the 

adaptors by pulling up on the handle 

C 

B 

Press the leg tube buttons in and slide the mouldings 

over until engaged. Pull on the rear wheel assembly to 

make sure it is locked on. 

C Remove the rear wheel assembly by pressing in and 

holding the moulding tabs, then slide off the leg tubes. 

A 

E 

F 

By pressing all the way in and holding the grey 

buttons on either side of the handle, rotate 

the handle backwards if desired. Reverse this 

procedure to rotate the handle back into the 

carry position. 

The Infant Carrier should now be locked onto 

the frame and ready for use. 

G Secure your baby into the Infant Carrier by the 

harness provided. See harness, 11. 

TO RELEASE THE INFANT CARRIER FROM THE 

ADAPTORS 

C 

E/H 

3. TO FIT AND REMOVE THE REAR WHEELS 

A 

B 

To fit, push in the black button, slide the wheels onto 

axle and release the button. Pull the wheels to make 

sure they are locked on. 

To remove, press in and hold the black button and 

slide wheel off the axle 

B/C 

A 

H Rotate the handle into the upright position 

by holding in the grey buttons and rotating 

forward. 

I 

J 

With one hand, hold the handle and with the 

other hand locate the release trigger under the 

‘head end’ of the Infant Carrier. 

Hold the handle, squeeze the release trigger 

and lift the Infant Carrier out of the frame. 

F 

I 

4. TO USE THE BRAKES 

WARNING: Always apply the brakes when parking the 

stroller. The stroller may roll away even if left unattended 

for a few moments. 

A 

B 

Push down with your foot on the bar or side levers to 

engage the brake mechanism. Make sure the brake is 

locked on. 

Lift the bar up to disengage the brake. 



05

5. FRONT SWIVEL WHEELS 

A 

B 

6. TO FIT, ADJUST AND REMOVE THE SEAT 

A 

B 

C 

To lock the swivel wheels, pull the tabs 

up. 

To unlock the wheels from the fixed 

position, push the tabs down. 

Line up the seat mouldings with the frame 

mouldings. Push down to engage the seat to the 

frame. Pull up on the seat frame to make sure it is 

locked into the frame. 

To adjust the seat positions, use your thumbs to 

press in and hold the grey buttons. At the same time 

rotate the seat and adjust to one of the three desired 

seat positions. 

To remove the seat, press in and hold the grey 

buttons. Then lift the seat out of the frame. 

NOTE: Do not adjust the seat position while your child is 

in the stroller. 

A 

B 

20. TO INSTALL THE ‘SNAP N GO’ INFANT CARRIER (sold separately) 

WARNINGS 

. 

. 

. 

. 

. 

Do not leave the child in the carrier for extended periods. 

The carrier is designed to provide mobility outside of the car but it should not be used 

instead of an appropriate cot. 

The carrier must be correctly fitted and locked into the stroller. 

The carrier must only be used with a Babylove stroller with compatible attachments. 

To be used only in a rearward facing position for a child weighing up to 9kgs and with 

a length of up to 700mm 

In the event of doubt about the method of installation, contact Babylove. 

NOTE: The Infant Carrier must be removed from the frame before folding. 

NOTE: Do not use this Infant Carrier with any other stroller. 

NOTE: Ensure the baby is secured in the Infant Carrier with the harness at all times. The 

Infant Carrier has been fitted with a hood when using with the stroller. The hood may also 

be used in the car. 

NOTE: Remove the Bassinette or Stroller Seat from the frame. Only the stroller frame and 

Infant Carrier adaptors are required. 

A 

Take one Infant Carrier adaptor at a time, with the 

RED button facing out, position them over the Seat 

connecting mechanism. Slide them down onto the 

seat connecting mechanism until they click on. 

B 

A 

C 

A 



15

19. TO REMOVE THE BASSINETTE FROM THE STROLLER FRAME 

7. TO FIT THE ARMBAR 

A 

B 

Release the Bassinette support bar from the 

basket tubing and secure to underside of 

the Bassinette. 

Standing beside the bassinette, with one 

hand holding the canopy handle and slightly 

lifting, push down one Bassinette release 

tab, while still slightly lifting, push down the 

other release tab and lift Bassinette up and 

away from the stroller frame. 

B 

A 

B 

Insert armbar into mouldings until engaged. 

Pull on the armbar to confirm it is locked in. 

To remove the armbar, press up on the two 

underside buttons and slide the armbar out. 

Warning: Do not lift the stroller by the armbar. It 

may disengage. 

A 

To fold the frame - see 14. 

B 

B 

8. CANOPY ATTACHMENT 

A 

Insert the canopy moulding into the frame moulding on 

both sides of the frame until locked in. 

B 

B 

To remove, press in the tabs on either side and pull out 

of frame moulding. 

C To adjust the canopy, rotate forwards or backwards to 

desired position. 

A 

B 



07

9. CANOPY WINDOWS 

A 

B 

Roll up canopy flap and secure with elastic 

and toggle. 

Roll up side flaps and secure with elastic 

and toggle. 

A 

18. TO FIT THE BASSINETTE TO THE FRAME 

WARNINGS 

. 

. 

. 

. 

Do not leave the child in the bassinette for extended periods. 

The bassinette must be correctly fitted and locked into the stroller. 

The bassinette must only be used with a Babylove stroller with compatible 

attachments. 

To be used only in a rearward facing position for a child weighing up to 9kgs and with 

a length of up to 700mm 

In the event of doubt about the method of installation, contact Babylove. 

B 

NOTE: The Bassinette must always be facing towards the handle. 

NOTE: The Bassinette must always be removed from the stroller frame before folding. 

10. ADJUSTING FOOTREST 

A 

Press in and hold the grey buttons and by lifting the 

footrest, adjust to the desired position. 

A 

A 

B 

Align the Bassinette mouldings over the frame 

mouldings and lower into the frame. Push down 

on the Bassinette and lock it into the frame. 

Release the Bassinette support bar from under 

the Bassinette and secure to the basket tubing. 

This eliminates any unneccessary movement and 

is more comfortable for the baby. 

A 

B 

B 



13

17. TO ASSEMBLE THE BASSINETTE (Bassinette sold separately) 

11. TO SECURE YOUR CHILD IN THE HARNESS 

A 

Using the webbing loop, pull each wire 

frame bar and lock into hooks on base. 

WARNING: Use this harness at all times. 

B 

Fit liner to Bassinette and secure the hook 

and loop tabs together. Pull the ‘D’ rings 

through the button holes and then fit the 

mattress. 

NOTE: D-rings are installed in the base of 

the bassinette for optional baby harness 

installation. Baby harness not supplied 

but can be purchased separately at an 

independent baby shop. 

A 

B 

A five-point harness is provided to restrain your child. 

To secure the child in the harness, push buckle (A) and 

(B) into the buckle housing (C) until the buckle prongs 

snap into position. Carefully adjust the harness by pulling 

the slider (D) until the desired fit is achieved in the lap, 

shoulder and crotch straps. Always adjust the harness 

when changing the seating position of the child. To 

release the buckle, squeeze the top and bottom prongs. 

C Adjust the canopy by pressing in the 

buttons and adjusting the desired position. 

D 

E 

Fit the bootcover to the front of the 

Bassinette. Secure to both sides of the 

canopy with the press studs. 

The Stroller Raincover can also be used for 

the Bassinette. 

B 

C 

12. TO FIT THE BOOTCOVER 

A 

B 

With armbar fitted, place the bootcover over the 

adjusting footrest and armbar. 

Secure the bootcover to the seat frame with the 

webbing straps provided. 

D 

C Secure the bootcover to the adjusting footrest 

with the hook and pile provided. Adjusting footrest 

should be in the higher position for best fitting of the 

bootcover. 

A 

C 

E 



09

13. TO FIT THE RAINCOVER 

14. TO FOLD AND CLOSE THE FRAME Cont’d 

A. Place over the canopy and seat and join hook 

and pile together on both sides. 

E 

Engage the frame lock. 

A 

D 

14. TO FOLD AND CLOSE THE FRAME 

NOTE: The seat must be removed before attempting 

to fold the frame. 

A 

Engage the brake. 

E 

B Remove the seat from the frame, see 6C. 

A 

15. TO REVERSE THE SEAT DIRECTION 

C With your right thumb, press in and hold button 

1 and at the same time squeeze in and hold 

button 2, press down on the handle and frame 

will begin to partially fold. 

D 

Hold the frame handle and release the grey 

second lock tab 3. Complete the frame folding 

by pulling up the frame handle and at the same 

time pushing forward on the main handle. 

C 

2 

1 

A 

Press in and hold the grey buttons. Then lift the seat out 

of the frame. Repeat steps 6A & 6B. 

NOTE: The seat must be removed before attempting to fold 

the frame. 

TO USE THE TETHER STRAP 

WARNING: Use the tether strap to prevent the stroller from 

rolling away. 

A 

C 

D 

3 

NOTE: A tether strap is fitted to this stroller, place the loop 

over the desired wrist when using this stroller. 

A 

Should you need to change wrist, remove the stroller 

strap and apply to the other handle. To ensure a tight fit, 

loop the tether strap around rather than over the handle. 

Open the end of the tether strap and insert the opposite 

end through opening created. Pull until tether strap 

tightens around handle. 

A 



11

FOCUS TRAVEL SYSTEM - Babylove

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?