ColorCascade Underwater Color Changing Light ... - Pentair

More documents

Recommendations

Info

2 Using an External Transformer for Multiple ColorCascade ® Lights When using multiple ColorCascade 12 VAC lights on a 100 Watt transformer, it is recommended that no more than four (4) ColorCascade lights be used. It is also recommended not to exceed 100 feet of total cable run between the transformer and lights. Note: For long cable lengths, set transformer to 14 VAC, and use only ColorCascade lights with the 150” cord option, see diagram below. 100 Watt Transformer 12 Gauge (Minimum) 100 ft. J Box Note: If a longer cable run is necessary, it is recommended that separate 100 Watt 12 VAC transformers be used for each light with no more than 100 feet of total cable run between the transformer and lights. Maximum wattage when using multiple ColorCascade and IntelliBrite ® Color LED lights (using a 300 Watt Transformer) IMPORTANT! When using multiple 12 VAC ColorCascade Light, IntelliBrite Light and IntelliBrite Landscape Lights, the total allowable light wattage is 300 Watts maximum. The ColorCascade and IntelliBrite light wattages are as follows: • One ColorCascade light is 16 Watts maximum • One GloBrite ® Light is 23 Watts maximum • One IntelliBrite Pool Light is 30 Watts maximum • One IntelliBrite Spa Light is 18 Watts maximum • One IntelliBrite Landscape light is 15 Watts maximum • One MagicStream ® Laminar is 16 Watts maximum COLORCASCADE ® Color Pool and Spa Light Installation and User’s Guide
3 ColorCascade Lights can be controlled using a standard wall-mount light switch or by the IntelliBrite ® Controller (see page 3). Multiple ColorCascade lights can be connected via a junction box and 12 VAC transformer to a single switch so that all lights can be switched on and off together. ColorCascade lights are controlled by cycling AC power to the 12 VAC transformer from a standard wall switch. By turning the switch Off and On a specific number of times, the light activates one of the seven light show modes, fixed colors, or enables the “Hold” and “Recall” feature, see page 6. Powering on the ColorCascade Light When the ColorCascade light is powered on, the previously selected color is displayed, unless the HOLD or RECALL feature was previously enabled. Note: If power to the light is off for more than five (5) seconds, the last color show mode or fixed color that was saved will be displayed. Selecting a ColorCascade light show mode or fixed color using a Wall Switch ColorCascade lights are compatible with IntelliBrite light colors and shows and can be synchronized with IntelliBrite ® lights. First switch power on to the light; the previously selected color is displayed, unless the HOLD or RECALL feature was previously enabled.. To select a color show mode (1-7) or fixed color (8-12), turn the wall switch Off/On a specific number of times. Each number (1-17) shown below corresponds to the number of times to power-cycle the switch to activate a color light show or fixed color. For details about saving color effects while in Show modes, see “Hold” and “Recall” feature on page 6. Number of times to cycle power (1-17) Operating ColorCascade ® Color Lights Using a Wall Switch 1 SAm Mode: Cycles through white, magenta, blue and green colors (emulates the Pentair SAm® Color Light). 2 Party Mode: Rapid color changing building energy and excitement. 3 Romance Mode: Slow color transitions creating a mesmerizing and calming effect. 4 Caribbean Mode: Transitions between a variety of blues and greens. 5 American Mode: Patriotic red, white and blue transition. 6 California Sunset Mode: Dramatic transitions of orange, red and magenta tones. 7 Royal Mode: Richer, deeper color tones. 8 Blue: Fixed color. 9 Green: Fixed color. 10 Red: Fixed color. 11 White: Fixed color. 12 Magenta: Fixed color. 13 Hold: Save the current color effect during a color light show. 14 Recall: Activate the last saved color effect. 15 White 16 Standard Mode 17 IntelliBrite Mode COLORCASCADE ® Color Pool and Spa Light Installation and User’s Guide
Page 1 and 2: COLORCASCADE ® UNDERWATER COLOR CH
Page 3 and 4: IMPORTANT WARNING AND SAFETY INSTRU
Page 5: ColorCascade ® Color LED Pool and
Page 9 and 10: 5 Operating ColorCascade ® Lights
Page 11 and 12: INSTALLING COLORCASCADE ® LIGHT FI
Page 13 and 14: 3. Set the niche in gunite as per c
Page 15 and 16: REPLACING THE COLORCASCADE ® LIGHT
Page 17 and 18: 13 AUXILIARY RELAYS AUX 1 ® EASYTO
Page 19 and 20: IntelliTouch ® Control System The
Page 21 and 22: PRINTED ON: 7/29/2009, 600054_ctlg
Page 23 and 24: PROBLEM CAUSE/ACTION 19 Troubleshoo
Page 25 and 26: Eyeball Replacement To replace the
Page 27 and 28: 23 ColorCascade ® Light Water Dept

ColorCascade Underwater Color Changing Light ... - Pentair

Create successful ePaper yourself

Delete template?

Save as template?