This application is included in the CP64S Data Sheet - Rane

DATA SHEET
CP64S
COMMERCIAL PROCESSOR
General Description
The CP64S is a versatile commercial preamplifier designed for
use in restaurants, bars, health clubs and offices. The CP64S is
capable of serving two independent Zones. Two gated Paging
inputs and four Program inputs are provided. Ports are provided
for expansion of Page, Program or Zone signals. Four levels of
priority are supported:
• Priority Page
• Non-Priority Page
• Priority Program
• Non-Priority Program
The versatility of the CP64S allows a wide variety of system
configurations while providing simple and intuitive controls.
Two gated Paging Inputs capable of receiving mic or line
level input are provided. Each features independent Mic/Line
Pad, Gain Trim, detector Threshold, Zone Assign and Zone
Level controls. Internally selectable phantom power is provided
for each input. Each Paging input may be summed Pre- or Post-
Zone Level control to allow setting Paging Level independent of
Zone Level. An internal Paging Priority switch allows a “master”
pager to override non-priority paging in its assigned zones, while
allowing true dual zone independent paging. If no Paging Priority
is selected, the Paging inputs mix together for applications
like karaoke.
Four stereo Program inputs are provided with independent
Input Level controls. Any one of the four Program inputs may
Optional SCP2S Equalizer-only Security Cover
be independently assigned in each Zone. One of the Program
inputs is a gated Priority Program input. When signal is detected
at its input, it overrides any non-priority Program selection in the
assigned Zones. The Priority detector features internal, adjustable
Threshold and Release-Time controls.
The CP64S has two Zone outputs: Zone 1 is stereo: Zone 2 is
mono. Each Zone features independent:
• Level
• Program Select
• Ducker On/Off
• Ducker Depth
• Servo-Locked-Limiter
• 7 Band EQ (±12 dB)
Versatile wired remote control interface ports are provided
for Paging assignment, Zone Level and Zone Program source
selection. Paging Zone and Source/Volume remote controls are
available as accessories.
Many options allow the installer to determine exactly which
controls are employee accessible. The SCP2S is an optional
security cover for the CP64S’s front panel EQ section. Any or all
other front panel knobs can be removed and replaced with hole
plugs — six are included with the SCP2S. Front panel Ducker
Depth controls are screw driver adjust. The remote controls allow
blank Decora plates to be remote control security covers. The
remote knobs can also be individually replaced with hole plugs.
Features
• Two fully independent gated Mic/Line Paging Inputs
• Paging Priority Assign
• Page Ducking
• Page / Program / Zone Expansion
• Three stereo Program Inputs
• One gated stereo Priority Program Input
• 7-Band graphic EQ for each Zone
• Servo-Locked-Limiter for each Zone
• Optional SCP2S Security Cover for EQ section only
• Optional PR2 Remote Page Assign Remote
• Optional ZR1 Remote Zone Level/Program Select Remote
• Universal Internal Power Supply (100-240 VAC)
Data Sheet-1

CP64S
COMMERCIAL PROCESSOR
Features and Specifications
Parameter Specification Limit Units Conditions/Comments
MIC/LINE PAGING INPUTS Two mono All controls duplicated for both inputs
..........Input Type Euroblock Balanced; Instrumentation amplifier
..........RFI Filter
Yes
..........Gain range +30 to +60 2 dB Continuously adjustable
..........Frequency Response 30 Hz to 40 kHz +0/-3 dB Maximum gain
..........Input Referred Noise -125 1 dBu Gain: 60 dB, Rs: 150 Ω, BW: 20 kHz
..........CMR 40 min dB 20 to 20 kHz
..........THD+N .05 .01 % Gain: 30 dB, +4 dBu out, 1 kHz, BW: 80 kHz
..........Phantom Power +15 4% VDC Internal switch
..........Mic Input impedance 500 1% Ω Each leg to ground
..........Line Pad 30 1 dB
..........Line Input impedance 14.5k 1% Ω Each leg to ground. Defeats phantom power
..........Signal Detector Range off to +4 typ dBu Continuously adjustable
..........Signal Detector Attack .5 typ msec Fixed
..........Signal Detector Release 3 typ sec Fixed
..........Overload Indicator +16 1 dBu 4 dB before clipping.
..........Front Panel Zone Assign Remote, Z1, Z2, Both Z1 = Zone 1; Z2 = Zone 2
..........Remote Zone Assign Off, Z1, Z2, Both Internal pull-up; Active low;
Switch closure to ground or 5 volt TTL logic.
..........Pre/Post Paging assign Summed with program Pre VCA or Post VCA via Internal switch
..........Page Priority Assign P1 (Page 1)
NO (none)
P2 (Page 2)
1 dBu Priority pager overrides non-priority pager only
in assigned zones; Selecting NONE allows the
two pagers to mix.
..........Paging Zone Level Adjust off to 0 dB Independent for each Zone
..........Page Remote Selector 11 = Off
10 = Z1 (Zone 1)
1 dBu Internal pull-up. Active low;
Switch closure to Ground or 5 volt TTL logic.
01 = Z2 (Zone 2)
00 = Both
PROGRAM INPUTS Four stereo All controls duplicated for all four inputs
..........Input Type RCA Unbalanced
..........Input Level adjust off to 0 dB
..........Frequency Response 10 Hz to 50 kHz +0/-3 dB
..........Input impedance 10 k 20% Ω
.....Priority Program Input
...............Input Detector Range off to -35 typ dBu Internal trim, factory set to -50 dBu
...............Release Time Range 5 to 20 typ sec Internal trim, factory set to 12 seconds
...............Attack Time 50 typ msec For a 20 dB step; Fixed.
...............Assign
OFF, Z1, Z2 or Both
EXPAND OUTPUTS
All controls duplicated for both zones
..........Number of Expand Outputs Two Z1 & Z2, both mono
..........Expand Selector
Zone
Program only
Page only
Note: If a Page signal is summed Post-VCA, it
is not present on the Expand Zone output. It is
available for the Expand Page output.
..........Output Type Balanced Cross-coupled; Euroblock connector
..........Gain: Zone 12 1 dB
....................Page/Program 6 1 dB
..........Frequency Response 10 Hz to 50 kHz +0/-3 dB
Data Sheet-2
continued...

CP64S
COMMERCIAL PROCESSOR
Parameter Specification Limit Units Conditions/Comments
..........S/N -84 1 dBr re +4 dBu. BW: 20 Hz-20 kHz
..........THD+N .05 .01 % +4 dBu, 1 kHz, BW: 80 kHz
..........Crosstalk -75 max dB 1 kHz, Rs: 25 Ω, ch/ch
..........Output impedance 100 1% Ω Each leg
..........Maximum Output +24 dBu typ Ri: 2 kΩ
ZONE OUTPUTS
..........Number of Outputs Two Zone 1 Stereo, Zone 2 mono
..........Output Type Euroblock Balanced; Cross-coupled
..........Gain: From Program Inputs 12 1 dB
....................From Page Inputs 6 1 dB
..........Frequency Response 10 Hz to 50 kHz +0/-3 dB
..........S/N -84 1 dBr re +4 dBu. BW: 20 Hz-20 kHz
..........THD+N .05 .01 % +4 dBu, 1 kHz, BW: 80 kHz
..........Crosstalk -75 max dB 1 kHz, Rs: 25 Ω, (L/R or ch/ch)
..........Output impedance 100 1% Ω Each leg
..........Maximum Output +20 typ dBu Ri = 600 Ω
..........Signal Present Indicator -20 typ dBu Maximum
..........Overload Indicator +16 typ dBu 4 dB before clipping
..........Ducker: Enable ON/OFF Independently defeatable for each Zone
...............Depth Range -50 to -6 typ dB Continuously adjustable
..........Limiter: Threshold Range -20 to +20 typ dB Continuously adjustable
...............Attack Time 20 typ msec For a 10 dB step; Fixed.
...............Release Time 250 typ msec For a 10 dB step; Fixed.
...............Ratio 15:1 typ Soft knee.
PROGRAM SELECTION
..........Local (Front Panel) L1, L2, L3 or P (priority) Independent for each Zone
..........Zone RMT Selector
11 = L1
10 = L2
00 = L3
01 = P
Attenuation = 64 mV/dB
Range 0 V to +5 V (0 dB to -78 dB)
..........Zone RMT Volume
(RMT engaged)
..........Off Isolation -80 typ dB 1 kHz, Rs: 25 Ω
EQ CIRCUITS
..........Boost/Cut Range +12 to -12 .5 dB
Internal pull-up. Active low.
Switch closure to ground or 5 volt TTL.
Gray Code logic.
Control element: 2 kΩ pot, reverse-log taper;
Or any ground referenced 0-5 VDC control.
..........ISO Center Frequencies 40, 100, 250, 630, 1.6k,
4k, 10k
3% Hz Zone 1: Stereo 7-band.
Zone 2: Mono 7-band.
..........Filter Bandwidth 2 3% oct
UNIT: Agency Listing
UL/cUL/CE
..........Universal Line Voltage 100-240 VAC, 50/60 Hz 12 watts
..........Construction
All Steel
..........Size 1.75"H x 19"W x 8.5"D 1U (4.4 cm x 48.3 cm x 21.6 cm)
..........Weight 5 lb (2.3 kg)
Shipping: Size 4.5" x 20.3" x 13.75" (11.5 cm x 52 cm x 35 cm)
..........Weight 9 lb (4.1 kg)
Note: 0 dBu = 0.775 Vrms
Data Sheet-3

CP64S
COMMERCIAL PROCESSOR
Block Diagram
P
R
O
G
R
A
M
I
N
P
U
T
S
LINE 1
LINE 2
LINE 3
PRIORITY
LEFT
RIGHT
LEFT
RIGHT
LEFT
RIGHT
LEFT
RIGHT
0 dB
0 dB
0 dB
0 dB
+
ZONE 2
INPUT
SELECTOR
ZONE 1
INPUT
SELECTOR
+
6 dB
+
6 dB
6 dB
DEPTH
-50dB
-6dB
PAGE
DUCKER
ON/OFF
DEPTH
-50dB
-6dB
PAGE
DUCKER
DEPTH
PAGE
DUCKER
+
+
MONO
*
+
SIG
OL
Z2 PRE PAGE
SIG
OL
+
PROGRAM
ZONE
PAGE
Z2 PAGE
PROGRAM
ZONE
PAGE
Z1 PAGE
6 dB
+
ZONE 2
EXPAND
-
7-BAND EQ
7-BAND EQ
+
6 dB
ZONE 1
EXPAND
-
Z2 LIMIT
THRESHOLD
-20dB
+20dB
Z2 VC
Z1 VC
Z1 LIMIT
THRESHOLD
-20dB
+20dB
+
+
+
6 dB
Z2 POST PAGE
6 dB
Z1 POST PAGE
6 dB
+
ZONE 2
-
+
ZONE 1 LEFT
-
+
ZONE 1 RIGHT
PRGM
PRIORITY
RELEASE
TIME *
12 24 SEC.
ON/OFF
Z1 PRE PAGE
7-BAND EQ
Z1 VC
+ -
11 OFF
10 Z1
01 Z2
00 BOTH
(ACTIVE LOW)
REMOTE ZONE ASSIGN
PAGE
ASSIGN
PAGE 1 + -
+
PAGE 2
-
P1
P2
P1
LOCAL ZONE ASSIGN
(FRONT PANEL)
11 RMT
P2
10 Z1
01 Z2
00 BOTH
P
A
G
E
I
N
PUTS
A
B
COM
A
B
COM
A
B
COM
A
B
COM
15V
PHTM PWR
*
MIC/
LINE
30dB
PAD
15V
PHTM PWR
*
MIC/
LINE
30dB
PAD
TRIM
TRIM
-60dBu -35dBu
PRGM PRIORITY
THRESHOLD *
P1 ACTIVE
P2 ACTIVE
30 TO 60dB
30 TO 60dB
PAGE DUCKER
P1
PAGER NONE
ASSIGN
LOGIC
P2
PAGE
PRIORITY *
PAGE 1 DETECT SENS.
-
+4dB
DET
P1
PAGE 2 DETECT SENS.
-
+4dB
DET
P2
Z1
A
Z2
B
COM
PRIORITY
ASSIGN
OFF
Z1
Z2
BOTH
PAGE BRIDGE
+
+
Z1 PAGE LEVEL
Z2 PAGE LEVEL
Z1 PAGE
Z1 PRE PAGE
*
PRE/POST VCA
Z1 POST PAGE
Z2 PRE PAGE
PRE/POST VCA
*
Z2 POST PAGE
Z2 PAGE
Z1
REMOTE
GRAY CODE
Z2
11 CH 1
10 CH 2 PROGRAM
01 CH 3
00 CH 4
SELECT
Z1
(ACTIVE LOW)
LOCAL
(FRONT PANEL)
Z2
PAGE
OL
OR
A
B
COM
A
B
COM
A
B
COM
A
B
COM
ZONE 1
LEVEL
CHANNEL
SELECT
LOGIC
RMT
LOCAL
(FRONT PANEL)
ZONE 2
LEVEL
RMT
LOCAL
(FRONT PANEL)
+5
+5
AUTO FADE
RMT SEL
ZONE 1
RMT/LOCAL
ZONE 2
RMT/LOCAL
RMT
RMT
+ Z1 VC +
Z2 VC
* INTERNAL CONTROLS
Data Sheet-4

L2
L1
PROGRAM SELECT
2
4 6
0
L3
LEVEL
10
P
8
3
6
12
24
1
Limit
Comp
Exp
Fault
Load
Ready
3
6
12
24
2
Limit
Comp
Exp
dB Headroom dB Headroom dB Headroom dB Headroom
Fault
Load
Ready
3
6
12
24
3
Limit
Comp
Exp
Fault
Load
Ready
3
6
12
24
4 ON
Limit
Comp
Exp
Fault
Load
Ready
MA 4
DIGITAL
AMPLIFIER
L2
L1
PROGRAM SELECT
2
4 6
0
L3
LEVEL
10
P
8
CP64S
COMMERCIAL PROCESSOR
L2 L3
L1 P
PROGRAM SELECT
4 6
2 8
0 10
LEVEL
Z1 Z2
OFF BOTH
PAGE 1 ASSIGN
Z1 Z2
OFF BOTH
PAGE 2 ASSIGN
ZR1
PR2
Remote Controls
Two optional wired remote control units are available. The PR2
allows remote control of Page 1 and Page 2 Zone Assign selection.
The ZR1 allows remote control of Zone Level and Zone
Program selection. One PR2 and two ZR1 remotes may be
used with each CP64S. The PR2 and ZR1 may be installed in
standard electrical boxes (minimum depth 2.25"). The remotes
connect to the CP64S through Euroblock connectors.
The PR2 is a 5-wire remote with 2 bits to select Page 1 Assign,
one wire for shield/gnd and 2 bits for Page 2 Assign. Selector
logic is active low BCD with pull-up provided in the CP64S.
Control may be a simple switch closure to ground or 5 volt TTL.
Page 1 and Page 2 bits may be paralleled so that one switch controls
both Page Assigns. Remote control is initiated by setting the
front panel Paging Zone Assign selector to RMT.
The ZR1 is a 5-wire remote with 2 bits for Zone Program
selection (active low Gray Code), a common shield/ground and
two wires for ratiometric DC control of Zone Level. Zone 1 and
Zone 2 ZR1 remote ports may be paralleled so that a single remote
controls both Zones. Selector logic is active low Gray Code
with pull-up provided in the CP64S. Control may be a simple
switch closure to ground or 5 volt TTL. Remote control for each
zone is initiated by engaging the RMT switch (located on the
front panel) for that Zone.
For installations that require a volume remote but don't need
the program selection of the ZR1, Rane makes the model VR1
Volume Remote.
Example System: Retail Store
CP64S
100-240 V
50/60 Hz 12 WATTS
RANE CORP. MADE IN U.S.A.
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
ACN 001 345 482
ZONE 2
Z2 PGM Z2 LEVEL REMOTES
OUTPUTS Z2 EXPAND Z2 MONO PROGRAM INPUTS
REMOTE PAGE REMOTE 1 INPUT 1 PAGING INPUTS
PRIORITY
ZONE ASSIGN WIRING
WIRING
LIMITER
ALL AUDIO AND
ZONE 1 ZONE 2
ASSIGN
PAGE 2 PAGE 1
MIN MAX
REMOTES ARE
ZONE L
L
Vr Vc
+8 +8
Z1 Z2
TRIM TRIM
CLASS 2 WIRING
off 1
ZONE 2 ZONE 1
2
EXPAND OUT EXPAND OUT
+30 +60 +30 +60
–20 +20 –20 +20
R
R
OL
1&2
PAGE 2 PAGE 1
Z1 PGM Z1 LEVEL
D1 D0 Vr Vc
ZONE PAGE
2
PGM
ZONE 1
ZONE PAGE
1
PGM
Z1 EXPAND Z1 RIGHT Z1 LEFT
+ – + – + –
PRIORITY 3 2 1
DETECT THRESHOLD
REMOTE 2 INPUT 2
Z2 Z1 + –
Z2 Z1R Z1L EX1 EX2
PRIORITY 2
IN1 IN2 PRIORITY 1
MIC
LINE
MIC
LINE
MA 4
MULTICHANNEL
AMPLIFIER
CD
PLAYER
PRE-RECORDED
ADVERTISEMENT
OR BREAK BELL
MUSIC
SERVICE
DVR
62 1:58
TELEPHONE HOLD MUSIC
TELEPHONE
PAGE OUT
DISTRIBUTED OUTPUTS REQUIRE
MT 4 TRANSFORMER ACCESSORY
ZR 1
DISTRIBUTED
ZR 1
STEREO
DISTRIBUTED
PROGRAM
SELECT
LEVEL
ZONE 2
PROGRAM
SELECT
LEVEL
ZONE 1 EXPAND 1
RETAIL / SHOP FLOOR
MEETING / DEMO ROOM
OFFICE PAGE
Data Sheet-5

TRANSFORMER
0 0
3
6
12
3
6
12
3
6
12
0 0
dB
CHANNEL OUTPUT HEADROOM
3
6
12
dB
CHANNEL OUTPUT HEADROOM
0
3
6
12
0
3
6
12
POWER
POWER
POWER
POWER
AMPLIFIER
AMPLIFIER
CP64S
COMMERCIAL PROCESSOR
Example System: Auto Dealer and Service
CP64S
100-240 V
50/60 Hz 12 WATTS
RANE CORP. MADE IN U.S.A.
MA 3
MULTICHANNEL
AMPLIFIER
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
REMOTES
OUTPUTS
PROGRAM INPUTS
PAGING INPUTS
Z2 LEVEL
REMOTE PAGE
Z2 PGM Z2 EXPAND Z2 MONO REMOTE 1 INPUT 1
ZONE ASSIGN WIRING
WIRING
LIMITER
PRIORITY
ALL AUDIO AND
ASSIGN
L
L
PAGE 2
ZONE 1 ZONE 2 PAGE 1
MIN MAX
REMOTES ARE
ZONE
Z1 Z2
TRIM TRIM
Vr Vc
CLASS 2 WIRING
+8 +8
off 1
ZONE 2 ZONE 1
2
EXPAND OUT EXPAND OUT
R
R
+30 +60 +30 +60
OL
–20 +20 –20 +20
1&2
PAGE 2 PAGE 1
ZONE PAGE ZONE PAGE
PRIORITY 3 2 1
DETECT THRESHOLD
MIC LINE MIC LINE
Z1 PGM Z1 LEVEL 2
Z1 EXPAND Z1 RIGHT Z1 LEFT
REMOTE 2 INPUT 2
1
PGM PGM
+ –
+ – + –
Z2 Z1 + –
D1 D0 Vr Vc
ZONE 2 ZONE 1
Z2 Z1R Z1L EX1 EX2
PRIORITY 2 IN2 IN1 TO SET PAGE
PRIORITY 3 PRIORITY 4
MUSIC
SUM PAGE 2
POST VCA
PRIORITY 2 PRIORITY 1 PRIORITY
SUM PAGE 1
& PAGE 2
POST VCA
SERVICE
ACN 001 345 482
1 2
3
MA 3
MULTICHANNEL
EXPAND 2
MUSIC ON HOLD
CD
10 8:58
PR 2
TELEPHONE
KEY SERVICE UNIT
Z1 Z2
OFF BOTH
PAGE 1 ASSIGN
ZR 1 ZR 1
Z1 Z2
OFF BOTH
PAGE 2 ASSIGN
L2 L3
L1 P
PROGRAM SELECT
4 6
2 8
0 10
LEVEL
DISTRIBUTED
(USE MT 4
TRANSFORMER
BELOW)
L2 L3
L1 P
PROGRAM SELECT
4 6
2 8
0 10
LEVEL
RIGHT
ZONE 2 ZONE 1
LEFT
12:00
MASTER
PAGE
RECEPTION
SALES & CREDIT
OFFICES
CP64S
100-240 V
50/60 Hz 12 WATTS
RANE CORP. MADE IN U.S.A.
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
ACN 001 345 482
ZONE 2
Z1 PGM Z1 LEVEL
D1 D0 Vr Vc
ZONE 1
ZONE PAGE
1
PGM
SALES FLOOR
Z1 EXPAND Z1 RIGHT Z1 LEFT
+ – + – + –
Z2
Z1L
EX2
PRIORITY 3
PROMO DVD
PRIORITY 3 2 1
EXPAND 1 EMERGENCY PAGE
DETECT THRESHOLD
IN2
PRIORITY 1
Z2 PGM Z2 LEVEL REMOTES
OUTPUTS Z2 EXPAND Z2 MONO PROGRAM INPUTS
REMOTE PAGE REMOTE 1 INPUT 1 PAGING INPUTS
PRIORITY
ZONE ASSIGN WIRING
WIRING
LIMITER
ALL AUDIO AND
ZONE 1 ZONE 2
ASSIGN
PAGE 2 PAGE 1
MIN MAX
REMOTES ARE
ZONE L
L
Vr Vc
+8 +8
Z1 Z2
TRIM TRIM
CLASS 2 WIRING
off 1
ZONE 2 ZONE 1
2
EXPAND OUT EXPAND OUT
+30 +60 +30 +60
–20 +20 –20 +20
R
R
OL
1&2
PAGE 2 PAGE 1
ZONE PAGE
2
PGM
MIC LINE
REMOTE 2 INPUT 2
Z2 Z1 + –
IN1 PRIORITY 2
SET PAGE
PRIORITY
TO P2
MIC
LINE
MA 3
MULTICHANNEL
AMPLIFIER
OPTIONAL SOURCES
PRIORITY 4
PR 2
OFF Z1 Z2 BOTH
MIC OR
TELEPHONE
PAGE TO
SERVICE
1 2
3
MA 3
MULTICHANNEL
CD
10 8:58
PAGE 1 ASSIGN
HOLE PLUG
MT 4 MULTICHANNEL TRANSFORMER
MT 4
MULTICHANNEL
SERVICE RECEPTION
ZR 1 ZR 1
L2 L3
L1 P
DISTRIBUTED
L2 L3
DISTRIBUTED DISTRIBUTED
L1
P
PROGRAM SELECT
4 6
2 8
0 10
LEVEL
PROGRAM SELECT
ZONE 2 ZONE 1
4 6
2 8
0 10
LEVEL
SERVICE WRITER
AND PARTS ROOM
SERVICE BAYS
EXPAND 2
RESTROOMS
Data Sheet-6

1
2
3
4 ON
3 Limit Fault 3 Limit Fault 3 Limit Fault 3 Limit Fault
6 Comp Load 6 Comp Load 6 Comp Load 6 Comp Load
12 Exp Ready 12 Exp Ready 12 Exp Ready 12 Exp Ready
24
24
24
24
dB Headroom dB Headroom dB Headroom dB Headroom
L2 L3
L1 P
PROGRAM SELECT
4 6
2 8
0 10
LEVEL
1
2
3
4 ON
3 Limit Fault 3 Limit Fault 3 Limit Fault 3 Limit Fault
6 Comp Load 6 Comp Load 6 Comp Load 6 Comp Load
12 Exp Ready 12 Exp Ready 12 Exp Ready 12 Exp Ready
24
24
24
24
dB Headroom dB Headroom dB Headroom dB Headroom
MA 4
DIGITAL
AMPLIFIER
L2 L3
L1 P
PROGRAM SELECT
4 6
2 8
0 10
LEVEL
MA 4
DIGITAL
AMPLIFIER
TRANSFORMER
Z1 Z2
OFF BOTH
PAGE 1 ASSIGN
Z2
BOTH
PAGE 2 ASSIGN
Z1 Z2
OFF BOTH
PAGE 1 ASSIGN
Z2
BOTH
PAGE 2 ASSIGN
CP64S
COMMERCIAL PROCESSOR
Example System: Karaoke Diner
CP64S
COMMERCIAL AUDIO
100-240 V
EQUIPMENT 24TJ
50/60 Hz 12 WATTS
RANE CORP. MADE IN U.S.A.
R
ACN 001 345 482
ZONE 2
Z2 PGM Z2 LEVEL REMOTES
OUTPUTS Z2 EXPAND Z2 MONO PROGRAM INPUTS
REMOTE PAGE REMOTE 1 INPUT 1 PAGING INPUTS
PRIORITY
ZONE ASSIGN WIRING
WIRING
LIMITER
ALL AUDIO AND
ZONE 1 ZONE 2
ASSIGN
PAGE 2 PAGE 1
MIN MAX
REMOTES ARE
ZONE L
L
Vr Vc
Z1 Z2
TRIM TRIM
CLASS 2 WIRING
+8 +8
off 1
ZONE 2 ZONE 1
2
EXPAND OUT EXPAND OUT
+30 +60 +30 +60
–20 +20 –20 +20
R
R
OL
1&2
PAGE 2 PAGE 1
ZONE PAGE ZONE PAGE
DETECT THRESHOLD
MIC LINE MIC LINE
Z1 PGM Z1 LEVEL 2 1
Z1 EXPAND Z1 RIGHT Z1 LEFT
PRIORITY 3 2 1
REMOTE 2 INPUT 2
D1 D0 Vr Vc PGM PGM
+ – + – + –
Z2 Z1 + –
ZONE 1 Z2 EX2 Z1R Z1L
PRIORITY 1
IN2 IN1
ZR 1
PR 2
MA 4
MULTICHANNEL AMPLIFIER
L2 L3
L1 P
PROGRAM SELECT
4 6
2 8
0 10
LEVEL
PROGRAM
SELECT
LEVEL
TRANS-
FORMER
SATELLITE
AUDIO
MUSIC
SERVICE
Z1 Z2
OFF BOTH
PAGE 1 ASSIGN
Z1 Z2
OFF BOTH
PAGE 2 ASSIGN
PAGE IN
LOUNGE OR
DINING AREA
SINGER 1
1-1-05
ZR 1
KARAOKE DVD
L2 L3
L1 P
PROGRAM SELECT
4 6
2 8
0 10
PROGRAM
SELECT
LEVEL
ZONE 2
ZONE 1
CH 68
DVR
SINGER 2
or ANNOUNCER
or DINING PAGE
LEVEL
62 1:58
DINING AREA
KARAOKE LOUNGE
OTHER PROGRAM SOURCE
Example System: Restaurant
CP64S
100-240 V
50/60 Hz 12 WATTS
RANE CORP. MADE IN U.S.A.
Z2 PGM Z2 LEVEL REMOTES
OUTPUTS Z2 EXPAND Z2 MONO PROGRAM INPUTS
REMOTE PAGE REMOTE 1 INPUT 1 PAGING INPUTS
PRIORITY
ZONE ASSIGN WIRING
WIRING
LIMITER
ALL AUDIO AND
ZONE 1 ZONE 2
ASSIGN
PAGE 2 PAGE 1
MIN MAX
REMOTES ARE
ZONE L
L
Vr Vc
Z1 Z2
TRIM TRIM
CLASS 2 WIRING
+8 +8
off
R
1
ZONE 2 ZONE 1
2
EXPAND OUT EXPAND OUT
+30 +60 +30 +60
–20 +20 –20 +20
R
R
OL
1&2
PAGE 2 PAGE 1
ZONE PAGE ZONE PAGE
DETECT THRESHOLD
MIC LINE MIC LINE
Z1 PGM Z1 LEVEL 2 1
Z1 EXPAND Z1 RIGHT Z1 LEFT
PRIORITY 3 2 1
REMOTE 2 INPUT 2
D1 D0 Vr Vc PGM PGM
+ – + – + –
Z2 Z1 + –
ZONE 1 ZONE 2
Z2 Z1R Z1L EX1 EX2
IN1 IN2
PRIORITY 3 PRIORITY 4
PRIORITY 2 PRIORITY 1
COMMERCIAL AUDIO
EQUIPMENT 24TJ
ACN 001 345 482
MA 4
MULTICHANNEL AMPLIFIER
1 2 3 4
TO TELEPHONE
MUSIC-ON-HOLD
MUSIC
SERVICE
PR 2
PAGE 1
CH 68
PAGE
ASSIGN
MT 4 70V
TRANSFORMER
DVR
10 8:58
Z1
OFF
HOLE
PLUG
MT 4
MULTICHANNEL
CD
RECEPTION
STATION
ZONE 2
ZONE 2
EXPAND
ZONE 1
ZONE 1
EXPAND
PR 2
HOLE
PLUG
PAGE 2
ZR 1
DISTRIBUTED
PROGRAM
SELECT
LEVEL
DISTRIBUTED
PATIO
DINING
ZR 1
DISTRIBUTED
PROGRAM
SELECT
LEVEL
10 8 19:58
DISTRIBUTED
RESTROOMS
JUKEBOX
Z1
OFF
OFFICE
PAGE
TELEPHONE
KEY SERVICE
MIC OR
TELEPHONE
PAGE
DINING ROOM
LOUNGE
OFFICES
Data Sheet-7

CP64S
COMMERCIAL PROCESSOR
Rear Panel
CP64S
100-240 V
50/60 Hz 12 WATTS
RANE CORP. MADE IN U.S.A.
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
ACN 001 345 482
Z2 PGM Z2 LEVEL REMOTES
OUTPUTS Z2 EXPAND Z2 MONO PROGRAM INPUTS
REMOTE PAGE REMOTE 1 INPUT 1 PAGING INPUTS
PRIORITY
ZONE ASSIGN WIRING
WIRING
LIMITER
ALL AUDIO AND
ZONE 1 ZONE 2
ASSIGN
PAGE 2 PAGE 1
MIN MAX
REMOTES ARE
ZONE L
L
Vr Vc
Z1 Z2
TRIM TRIM
CLASS 2 WIRING
+8 +8
off 1
ZONE 2 ZONE 1
2
EXPAND OUT EXPAND OUT
+30 +60 +30 +60
–20 +20 –20 +20
R
R
OL
1&2
PAGE 2 PAGE 1
ZONE PAGE ZONE PAGE
DETECT THRESHOLD
MIC LINE MIC LINE
Z1 PGM Z1 LEVEL 2 1
Z1 EXPAND Z1 RIGHT Z1 LEFT
PRIORITY 3 2 1
REMOTE 2 INPUT 2
D1 D0 Vr Vc PGM PGM
+ – + – + –
Z2 Z1 + –
Architectural Specifications
The processor shall provide two fully independent gated paging
inputs, three line-level non-priority program inputs and one
gated line-level priority program input. Two zone outputs shall
be served. Zone 1 shall be a stereo zone with balanced, crosscoupled
outputs. Zone 2 shall be a mono zone with a balanced
cross-coupled output. Mono expansion ports for page, program
or zone signals shall be provided for each zone. Wired remote
control ports shall be provided for paging zone assign, zone
program select and zone level.
Page inputs shall use a 5-pin Euroblock connector. Paging
controls shall include:
• 30 dB mic/line input pad.
• Input gain trim range of 30 dB to 60 dB.
• Mic gate threshold (range -∞ to +4 dBu).
• 15 volt phantom power (internal switch).
• Paging priority (page 1, none, page 2; internal switch).
• Pre- or post-zone level summing (internal switch).
• Front panel paging zone assign (Remote, Z1, Z2, Both).
• Remote paging zone assign (Off, Z1, Z2, Both).
• Paging zone level.
Each Program input shall have stereo RCA input jacks and
independent input level control. The priority program assign
switch shall provide priority program override to zone 1, zone 2,
both, or neither (off). The gated priority program input shall
have internally adjustable threshold and release time controls.
Zone outputs shall use 3-pin Euroblock connectors. Zone
controls shall include:
• Ducker on/off
• Ducker depth (-6 to -50 dB)
• Program select (L1, L2, L3, P)
• Zone level
• 7-band graphic equalizer (±12 dB)
• Servo-Locked-Limiter threshold (-20 to +20 dBu)
• Mono switch for Zone 1 (internal)
• Remote engage switch
Wired remote ports shall use 3-pin Euroblock connectors.
Remote logic shall be active low with internal pull-up. Remote
level control shall be ratiometric DC control with 5 volt
reference.
The unit shall be capable of operation by means of its own
built-in universal power supply operating at 100-240 VAC and
meet CE requirements. The unit shall be UL and cUL listed. The
unit shall be entirely constructed from cold-rolled steel.
Reliability and efficiency are to be primary design considerations.
The unit shall be a Rane Corporation CP64S Commercial
Processor.
Available Accessories
• SCP2S Security Cover (for EQ section)
• SC 1.7 Security Cover (for entire front panel)
• PR2 Page Assign Remote Control
• ZR1 Zone Source/Volume Remote Control
• VR1 Volume Remote Control
• Hole Plugs (6 Provided with SCP2S)
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5000 USA TEL 425-355-6000 FAX 425-347-7757 WEB rane.com
Data Sheet-8
All features & specifications subject to change without notice. DOC 102906