SUBSECTION B

More documents

Recommendations

Info

Type number Joint description Limitations Joint Categories Degree of Radiographic Examination. Full Spot None 2 •Single-welded butt joint with backing strip other than those included under (1) (a) None except as in (b) below (b) Circumferential butt joints with one plate offset; see UW-13(b) (4) and Fig. UW-13.1, sketch (i) A, B, C & D A, B & C 0.90 0.90 0.80 0.80 0.65 0.65 Fion Zhang/ Charlie Chong UW-12
Type number Joint description Limitations Joint Categories Degree of Radiographic Examination. Full Spot None 3 Single-welded butt joint with out used of backing strip. Circumferential butt joints only, not over 5⁄8 in. (16 mm) thick and not over 24 in. (600 mm outside diameter) A, B, C NA NA 0.6 Fion Zhang/ Charlie Chong UW-12
Page 1 and 2:
SUBSECTION B REQUIREMENTS PERTAININ
Page 3 and 4:
PART UW Overview Fion Zhang/ Charli
Page 5 and 6:
Type number Joint description Limit
Page 7 and 8:
UW-2 SERVICE RESTRICTIONS. Fion Zha
Page 9 and 10:
UW-2 SERVICE RESTRICTIONS Class a b
Page 11 and 12:
UW-2 Class a Description. Vessels a
Page 13 and 14:
WELDED JOINT CATEGORY ASME VIII pre
Page 15 and 16:
• Cat “A” includes all longit
Page 17 and 18:
Non-hemispherical head Critical Cir
Page 19 and 20:
• Cat B includes most circumferen
Page 21 and 22:
• Cat D includes welded joints co
Page 23 and 24:
The main content relates to two are
Page 25 and 26:
(d) Except when the longitudinal jo
Page 27 and 28: staggered or separated by a distanc
Page 29 and 30: Based on the ASME Code requirement
Page 31 and 32: Fion Zhang/ Charlie Chong UW-11
Page 33 and 34: Item 3: All butt welds in an unfire
Page 35 and 36: RT Item Note Joint Efficiency (Type
Page 37 and 38: UCS-57 RADIOGRAPHIC EXAMINATION In
Page 39 and 40: UW-11(a2) all butt welds in vessels
Page 41 and 42: UW-11 RADIOGRAPHIC AND ULTRASONIC E
Page 43 and 44: UW-11(a) Full Radiography (1) all b
Page 45 and 46: Except as required by UHT-57(a), Ca
Page 47 and 48: Any vessel with welded joint exceed
Page 49 and 50: in which case: (a)Category A and B
Page 51 and 52: (7) ultrasonic examination in accor
Page 53 and 54: Full Radiography means UW-11 (a-5):
Page 55 and 56: Radiographic examination is not req
Page 57 and 58: UW-11(d,e,f) Special welding proces
Page 59 and 60: http://www.mechanicalengine eringbl
Page 63 and 64: UW-12 JOINT EFFICIENCIES Fion Zhang
Page 65 and 66: Summary of weld types: Type 1: Full
Page 67 and 68: Type number Joint description Limit
Page 71 and 72: Summary Maximum Weld Joint Efficien
Page 73 and 74: Butt joints as attained by double-w
Page 75 and 76: TABLE UW-12 MAXIMUM ALLOWABLE JOINT
Page 77: Weld type number 1: Single “V”
Page 85 and 86: GENERAL NOTES: (a) The single facto
Page 87 and 88: UW12(d) Seamless vessel sections or
Page 89 and 90: UW12(d) • all Category A welds ar
Page 91 and 92: Q. Given a seamless head or shell s
Page 93 and 94: Hemispherical head • 100% RT UW-5
Page 103 and 104: FIG. UW-16.1 SOME ACCEPTABLE TYPES
Page 105 and 106: t c = not less than the smaller of
Page 107 and 108: Exercise: Problem: A nozzle is bein
Page 109 and 110: FIG. UW-16.1 SOME ACCEPTABLE TYPES
Page 115 and 116: • t = nominal thickness of vessel
Page 117 and 118: where it meets a set-on nozzle, by
Page 119 and 120: Q3. ASME VIII section UW-16 (c) fig
Page 121 and 122: Q5. ASME VIII section UW-16 (d)(1)
Page 123 and 124: UW-40(f ) The term nominal thicknes
Page 125 and 126: UW-40(a), the soak band shall conta
Page 127 and 128: fillet welds, the nominal thickness
Page 129 and 130:
The nominal thickness 6. When a wel
Page 131 and 132:
Mr. “t” the nominal thickness (
Page 133 and 134:
Mr. “t” the nominal thickness e
Page 135 and 136:
UW-50 NONDESTRUCTIVE EXAMINATION OF
Page 137 and 138:
UW-51 RADIOGRAPHIC EXAMINATION OF W
Page 139 and 140:
10-13 RECORDS RETENTION a) The Manu
Page 141 and 142:
(c) For manufacturers of UM stamped
Page 143 and 144:
When do you need full RT Fion Zhang
Page 145 and 146:
UW-11, a(2). All materials; welded
Page 147 and 148:
UW-11 (a3) all butt welds in the sh
Page 149 and 150:
UW-11 (a6) all butt welds joined by
Page 151 and 152:
UW-51 (a2) A written radiographic e
Page 153 and 154:
Demonstration of (1) density and (2
Page 155 and 156:
Demonstration of (1) density and (2
Page 157 and 158:
• Repaired welding, at the option
Page 159 and 160:
Unacceptable imperfections UW-51 (b
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
UW-51 (b3) any group of aligned ind
Page 167 and 168:
Page 169 and 170:
UW-51 (b2) http://www.ndted.org/Edu
Page 171 and 172:
In-progress RT for quality improvem
Page 173 and 174:
This rule also addresses smaller, o
Page 175 and 176:
UW-52 (b2) For each increment of we
Page 177 and 178:
Welder-C Welder-B Welder-A Under co
Page 179 and 180:
UW-52 (b3) Each spot examination sh
Page 181 and 182:
UW-52 (b4) Radiographs required at
Page 183 and 184:
UW-52 (b4) Radiographs required at
Page 185 and 186:
UW-52 (c) Standards for Spot Radiog
Page 187 and 188:
Spot radiographs may be retained or
Page 189 and 190:
UW-51 (b2) t = the thickness of the
Page 191 and 192:
UW-52(d) Evaluation and Retests UW-
Page 193 and 194:
UW-52(d) Evaluation and Retests (1)
Page 195 and 196:
Fion Zhang/ Charlie Chong
show all

SUBSECTION B

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?