TL 8430-0060 - Bundesamt für Wehrtechnik und Beschaffung

Bundesamt
für Wehrtechnik
und Beschaffung
Technische Lieferbedingungen
Inner Boot, Mountain Ski
Date of issue:: 25 July 2006
TL 8430-0060
Issue 3
Page 1 of 9 Pages
In case of doubt the German original is binding.
Stock number:
Item name:
8430-12-369-1314 BOOT, MOUNTAIN/SKI, size 225
(for complete list see 2.2)
Project reference number:
Project reference name:
8430-01072 Inner Boot, Mountain/Ski
Procurement types
(X)
Code
(X) Not tied to any manufacturer.
C
( ) Tied to a group of manufacturers by an agreement on user rights. E
( ) Tied to approved manufacturers. F
( ) Tied to a single manufacturer. H
Topicality check of this Technical
Specification (TL) is required.
Change with
respect to the
previous issue
Change of shoe size range Previous issue 1 2
Previous dates of issue 03.05 01.06
May be obtained from BWB, Koblenz; www.bwb.org (Auftraggeber Bw)
© Bund; Originator: Bund, Copyright note i.a.w. DIN ISO 16016 to be observed

Page 2 TL 8430-0060
CONTENTS
NORMATIVE REFERENCES
1 GENERAL
1.1 Scope
1.2 General technical-organizational requirements
1.3 Environmental compatibility
2 TECHNICAL REQUIREMENTS
2.1 Technical data package
2.2 Scope of delivery
2.3 Materials
2.4 Technical data
2.5 Manufacture
2.6 Marking of supply items
3 QUALITY ASSURANCE
3.1 Quality inspections
3.2 Contractor quality control
3.3 Government quality assurance
4 PACKAGING
4.1 Unit package
4.2 Shipping package
4.3 Marking of packaging materials
Annex A: List of materials
Annex B: Marking of the unit and shipping package
Annex C: Figure
NORMATIVE REFERENCES
By dated and undated references, this TL includes requirements specified in other documents
(standards, TLs etc.). These documents are cited in the respective text passages (normative
reference). All documents cited in this TL are listed below. In case of dated references
later changes or revisions of the cited documents apply to the present TL only after their
incorporation. The respective issue of the cited documents valid at the time of the
conclusion of the contract applies in case of undated references.
DIN 1451–3
DIN 55510
DIN 55479
TL 8100-0072
TL 8100-0101
TL 8305-0011
Lettering; Linear-Antiqua without serifes;
lettering for printing
Packaging; Dimensional coordination in the field of packaging
Modular sub-multiples of the 600 mm x 400 mm area module
Packaging – types of sealings of cartons and boxes by means of
pressure-sensitive adhesive tape and gummed paper tape *)
Packaging - Marking of packaging materials for their material
recycling
Packaging, material protection by means of preservation and
packaging; packing level C (NATO-4)
Woven fabrics made of natural, manmade and blended fibres as
well as clothing, underwear and equipment items manufactured
from such fabrics (general terms)

TL 8430-0060 Page 3
TL 8400-0007
Footwear, handwear, bags and other items made of leather or
leather substitutes (general terms)
*) Document not available in an English version
Sources of Supply:
TL: Bundesamt für Wehrtechnik und Beschaffung, Postfach 300165, 56057
Koblenz; www.bwb.org (Auftraggeber Bw)
DIN:
Beuth Verlag GmbH, 10772 Berlin
1 GENERAL
1.1 Scope
The inner boot, mountain/ski, is worn together with the outer boot, mountain/ski,
by soldiers of the mountain troops for military skiing in alpine terrain. It can
also be used as alpine hut shoe.
1.2 General technical-organizational requirements
In accordance with TL 8400-0007 and TL 8305-0011. Special attention should be
paid to the requirements with respect to health, safety and environmental
protection.
1.3 Environmental compatibility
In accordance with TL 8305-0011.
2 TECHNICAL REQUIREMENTS
2.1 Technical data package
Die inner boot is a lined laced shaft boot with loop lacing, padded upper collar
and bonded, slightly profilated concave rubber sole.
The inner boot, mountain/ski, shall be manufactured according to the sealed
models BSS-99 and on plastic last BSS-85.
Lasts and models may be obained from Brüder Winkle GmbH + Co. KG, Fabrikstraße 7
in 89281 Altenstadt/Iller or Fagus GreCon GmbH & Co. KG, Hannoversche Straße 58
in 31061 Alfeld/Leine.
Article 1872041 inner boot Multi of Messrs. Lowa, 85305 Jetzendorf, or
equivalent.
2.2 Scope of delivery
Size Stock number ASD (Article Bulk Data)Number
225 8430-12-369-1314 15080B280
232 8430-12-369-1315 15080B020
240 8430-12-347-1243 15080B040
247 8430-12-347-1244 15080B060
255 8430-12-347-1245 15080B080
262 8430-12-347-1246 15080B100
270 8430-12-347-1247 15080B120
277 8430-12-347-1248 15080B140
285 8430-12-347-1249 15080B160
292 8430-12-347-1250 15080B180
300 8430-12-347-1251 15080B200
307 8430-12-347-1252 15080B220
315 8430-12-347-1253 15080B240
322 8430-12-347-1254 15080B250
330 8430-12-347-1255 15080B260

Page 4 TL 8430-0060
Materials
The materials to be used are specified in the list of materials, Annex A.
2.4 Technical data
Weight (per pair), size 270: ≤ 790 g
2.5 Manufacture
The inner boots shall be manufactured as high-quality work.
Type of manufacture:
Outsole:
Strobel-stitched
bonded
2.6 Marking of supply items
Affixing brand or company logos is not permitted. Marking exclusively according
to the requirements specified in the respective valid TL.
The outsole (toe part) of the inner boot shall be marked with the size.
Additionally, a label indicating size, month and year of delivery, and the number
of the supplier (e.g.: 270 02 05 0000) shall be fixed to the inside of the tongue
2 cm away from the upper edge.
3 QUALITY ASSURANCE
3.1 Quality inspections
No specific requirements.
It is presupposed that the Contractor ensures the fulfilment of the technical
requirements by conducting item-related acceptance tests and documenting the
results (refer to 3.2).
3.2 Contractor quality control
No special requirements.
Die Contractor shall inspect the supplies and/or services for contractual
conformity and document the result.
3.3 Government quality assurance
4 PACKAGING
Not applicable, unless indicated otherwise in the contract.
For packing level C (NATO-4) in accordance with TL 8100-0101, the packaging shall
be conducted taking the following additional requirements or deviations into
account:
4.1 Unit package
Each pair of inner boots, mountain/ski, shall be packed into a commercial box,
provided with ventilation holes, so as to be resistant to vibration.
Marking of the unit package
According to Figure B.1

TL 8430-0060 Page 5
4.2 Shipping package
5 unit packages each, identical in size, shall be packed into a collapsible
cardboard box with butting outer bottom and top flaps so as to be resistant to
vibration.
Double-wall corrugated boxes shall be used of a quality that guarantees a
stacking height of 2.50 m without box deformation (especially in the lower box
layers).The shipping package shall be provided with ventilation holes.
Outer dimensions of the shipping package in accordance with DIN 55510 (maximum
dimensions)
600 mm x 400 mm x 375 mm
(plus tolerances are not admissible)
Closure
Double-T seal in accordance with DIN 55479, index number 3 by means of a
suitable, well sealing tape or gummed paper tape.
When closing the boxes, attention must be paid that the closure flaps at bottom
and top are butting.
Marking of the shipping package
According to Figure B.2.
4.3 Marking of packaging materials
Unless provided with the ”Green dot“, the packaging materials shall be marked in
accordance with TL 8100-0072 as required in the packaging regulation.

Page 6 TL 8430-0060
Annex A
List of Materials
Lower side and tongue
part:
Montafon +2xN7, black, Messrs. Nemes or equivalent
Lower edging part
(inner collar), upper
tongue part, loop
base:
Montecchio 7/85-SM, Messrs. Spac
or equivalent
Edging, flexion
insert, tongue tip:
Woven fabric, nylon, black
Edging and upper
tongue lining:
Quarter and lower
tongue lining:
Astra / MTP 3.5 black, Messrs. Pantatex
or equivalent
Duraterm KL, Messrs. Gore
or equivalent
Edging – ankle -
tongue padding:
Reticulated foam
Thickness: 10 mm, weight per unit volume 100 g/dm 3
Side padding:
Thinsulate CS 150, Messrs. Wilhelm,
or equivalent
Ankle fixation:
Reticulated foam
Thickness: 7 mm, weight per unit volume 120 g/dm 3
Reinforcing material: K 80 H/555-P 11, Messrs. Pfirrmann
or equivalent.
Insole:
Nonwoven 133/25 with Thinsulate CS 150, thickness: 4 mm,
Messrs. Wilhelm, or equivalent
Counter: Ski, Lefa (sizes: 232 – 240, 247 – 270, 277 – 300,
307 – 330), Messrs. LOWA or equivalent
Loop tape:
Nylon tape, black, 10 mm wide
Topline tape:
Eyelets:
9602, twilled tape, 14 mm wide, black, Messrs. Jäger or
equivalent
Rolled eyelet with mating eyelet, 1872 R antique copper,
with dark coating, Messrs. Mark or equivalent

TL 8430-0060 Page 7
Lacing hook:
Rivet:
Hook patch and loop
patch (hook-and loop
fastener)
405 CuFe hook, antique copper, riveted, Messrs. Mark or
equivalent
S 4/7/7 mm CuFe rivet, antique copper, Messrs. Mark or
equivalent
20 mm wide, black
Sewing thread:
Polyamide
Outsole:
Laces:
4544, concave thermoplastic rubber (TR) sole, slightly
profilated, Messrs. LOWA or equivalent
9139, water-repellent, black, Messrs. Sauter or equivalent
Size
Length in cm
232 – 247 120
255 – 285 130
292 – 330 140
Inlay soles:
Kilima, Messrs. LOWA or equivalent

Page 8 TL 8430-0060
Annex B
Marking of unit package Figure B.1
- Stock number
- ITEM NAME
- QUANTITY AND UNIT
(EA) each / SE = set / PR = pair
- Date of delivery
- Order number
- Contractor
. . . . - . . - . . . - . . .
...........................................................
...........................................................
........... .... Größe/Weite..........................
. . / . .
. / . . . . / . . . . . / . . . . .
.............................................................
....................................................
Glossary:
Größe/Weite = Size/Width
Type: Imprint, stick-on label or slip label
Format: Adapted to the space available
Lettering: In accordance with DIN 1451-3 or comparable block letters,
stock number, item name and packaging data to be set off by means of boldface
and size
Colour: Black, permanent and abrasion-resistant
Marking of the shipping package
- Stock number
- ASD (Article bulk data) number
– ITEM NAME
- QUANTITY AND UNIT
(EA) each / SE = set / PR = pair
– Packaging data
(packaging level / date of delivery (e.g.
(C – 02/06)
– Gross weight and volume
– Lot number:
- Order number
- Contractor
- Consignee
- Stacking height
Glossary:
Größe/Weite = Size/Width
Stapelhöhe = Stacking height
Figure B.2
. . . . - . . - . . . - . . .
...........................................................
...........................................................
........... .... Größe/Weite .........................
. - . . / . .
. . . . kg . . . m 3
. . . . . .
. / . . . . / . . . . . / . . . . .
..........................................................
...........................................................
Stapelhöhe: 2,50 m
C
Type: Imprint or white stick-on label
Format: In analogy to DIN A5 or adapted to that format in case of smaller box height
Lettering: In accordance with DIN 1451-3 or comparable block letters,
stock number, item name and packaging data to be set off by means of boldface
and size (12 mm minimum)
Colour: Black, permanent and abrasion-resistant
Additional indication of packing level (e.g. packing level C):49 mm in size.
Annex C

Inner boot, mountain/ski
TL 8430-0060 Page 9