25.09.2014 Views

7130 Oil Burner Controls LMO14... LMO24... LMO44...

7130 Oil Burner Controls LMO14... LMO24... LMO44...

7130 Oil Burner Controls LMO14... LMO24... LMO44...

SHOW MORE
SHOW LESS

You also want an ePaper? Increase the reach of your titles

YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.

Operation, display, diagnostics (cont´d)<br />

Diagnostics of the<br />

cause of fault<br />

After lockout, the red fault signal lamp remains steady on. In that condition, the visual<br />

diagnostics of the cause of fault according to the error code table can be activated by<br />

pressing the lockout reset button for more than 3 seconds. Pressing the reset button<br />

again for at least 3 seconds, the interface diagnostics will be activated. Interface diagnostics<br />

works only if the AGK20… lockout reset button extension is not fitted.<br />

For more detailed information, refer to Data Sheet N7614.<br />

The following sequence activates the diagnostics of the cause of fault:<br />

OCI400<br />

Lockout position Lockout position Lockout position<br />

Visual diagnostics<br />

Interface diagnostics<br />

On<br />

Flashing<br />

PC / analyzer<br />

EK<br />

> 3 s<br />

Error code table<br />

xxxxxxxx<br />

xxxxxxxx<br />

xxxxxxxx<br />

xxxxxxxx<br />

xxxxxxxx<br />

xxxxxxxx<br />

EK<br />

> 3 s<br />

<strong>7130</strong>z04e/0602<br />

EK<br />

< 3 s<br />

Reset<br />

Red blink code of signal<br />

lamp (LED)<br />

2 blinks<br />

hh<br />

3 blinks<br />

hhh<br />

4 blinks<br />

hhhh<br />

5 blinks<br />

hhhhh<br />

6 blinks<br />

hhhhhh<br />

7 blinks<br />

hhhhhhh<br />

8 blinks<br />

hhhhhhhh<br />

9 blinks<br />

hhhhhhhhh<br />

10 blinks<br />

hhhhhhhhhh<br />

10 blinks<br />

hhhhhhhhhh<br />

Error code table<br />

«AL» at Possible cause<br />

term. 10<br />

On No establishment of flame at the end of «TSA»<br />

- Faulty or soiled fuel valves<br />

- Faulty or soiled flame detector<br />

- Poor adjustment of burner, no fuel<br />

- Faulty ignition equipment<br />

On Free<br />

On<br />

On<br />

On<br />

On<br />

On<br />

On<br />

Extraneous light on burner startup<br />

Free<br />

Free<br />

Too many losses of flame during operation (limitation<br />

of the number of repetitions)<br />

- Faulty or soiled fuel valves<br />

- Faulty or soiled flame detector<br />

- Poor adjustment of burner<br />

Time supervision oil preheater<br />

- <strong>Oil</strong> preheater failed 5 times during prepurging<br />

Free<br />

Off Wiring fault or internal fault, output contacts, o-<br />

ther faults<br />

On 3 times temporary fault of the output contacts<br />

During the time the cause of fault is diagnosed, the control outputs are deactivated burner<br />

remains shut down.<br />

The diagnostics of the cause of fault is quit and the burner switched on again by resetting<br />

the burner control. Press the lockout reset button for about 1 second (< 3 seconds).<br />

10/13<br />

Siemens Building Technologies<br />

CC1N<strong>7130</strong>en<br />

HVAC Products 12.12.2005

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!