HEGNER LKH 950 Duplicator Manual

I,
T{EENER
Instruction for Assembly & 0perotion of
DUPLICATING ATTACHMENT LKH 950

':i.i i.l ,
''::; ,... :
-2
Aliqnment of Cutter
Cutter is factory aligned.
.u"i:g supptied If cutter
gruge (p""i
has moved, align.cutter
6)
oy trghtening as shown byr
hex screws.
in diagram. S""u""-"rtir"
Duplicatinq from a Turninq
Place the turning you rrvish
the rear
to duplicate
of between
the, iupii""io; the two centers
i;; may have
at
to accomodate the i"ngih-or'iiJ
to reposition pr""e one center
the blank. position you are dupricating). Mount
at "6rr", fp".t rz j-o,r-irp'ii"lt""
the s m a I l e s t---oilJ"tu","r so that it rests
wheel (part 9) counLe."fo"lriue,unti]
tn""[i""- t" be copied. cutter (part Turn
far enough from br.ank;;-il;t;lank B) is retracted
and lower cutter, can by. tu"n ile"ry. Turn on rathe
starts to cut inro btank.
lu"ninf-rnJur
d"il;,1o (p;;f gi"i""p,rse untit eutter
at a time, eaeh time movi"g-irpri"gtiil iurn;;;;"?;"rr ?) r/2
;;;;"'ltong. Lo2 rurns
of turning bv means of J.ari"-"[or."o;#"i-;;'ir,, entire rensrh
until vou reach tne oesir"i-oi5r"ter r";nt of the
in
iathe,
to turn more than
In"-r"llpiece.
one dupricate If you
of the ;; ;;., need
and set the dupli:,"tol d;il-;;uq" (p""i-iol"""-rhat
turn rathe off
part lr' Lock depth aa;ustmenE-i;to it rouehes
No' bosition ji
r5) ' The duori""t;;-;;"'io, tignt"ning nut (part
additional blanls "orr"ted
properiy
to identical to dupricate
drameters.
Duplicatinq from a Template
Remove centers for^holding turnings o! duplicator. and mount tempJ-ate
ho'Lders instead'- see oi"g""r'fo" rn*irum'and minimum dimensions
arlowed for temo-r"t"' --ri;il"'tempiaiu"in"i'Jrpr.te horders by
tightenins screws' I*grii"i:rot"i"-n"ii"""""!""pt remprates up ro
i" *;ff:"ffJ.:::. o,piii"i;;-;"
Sharpenino of Cutter
IHPORTANI: Angle of cutter
required, but only from the
the angle of the cutter.
must
be altered. Sharpen
INNERnot
surface,
cutter when
taking care not to alter

fnstruction for Assembly & Operotion of Duplicoting Attochment LKH 950
Mounting of Duplicoting Attochment LKH 950
5
..\
6
\
Mount duplicoting ottochment by positioning unit of reor of lothe ond
fosten to lothe bed with two bolts (tto. l ) supplied. Moke sure surfoces
(t{o. 2) rest ogoinst lothe bed ond surfoce (No. 3) rests ogoinst
heod stock (Uo. 4).
Remove nut (No. 7) from shoft
Slide spoked wheel onto shoft
(ruo. 6) ot left front of duplicotor.
(No. 5) ond secure by replocing nut (No.Z).

Duplicoting Attochment LKH 950
9 Wheel
l5 Nut
Gouging surfoce
Depth
?3unu
11
Finger
z'\
I
tt;
-- l- -. I
\J
-.- \/
'--.-
\!
'-J.-,'
I
I
12
RoIler
13 Arm
8 Cutter
6 Gouge
Templote
t/4" tnic*
I
!o
-t
(r)
;x i-
io
l=

$=:Q-e r\
OJ
a:g E
ratO
\r \P€
qqs
llY
EB E
r
E
$:
E-o
rN IN lOr
@Y
//r8
/a
/a /o gN
E4
,xs-6gr{fs
s6-J_ffi=t
T
I
(o
t
o