Tech Data Sheet - MyAutoProducts.com
Tech Data Sheet - MyAutoProducts.com
Tech Data Sheet - MyAutoProducts.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
■ Fast Drying Easy Mix (4:1)<br />
■ High Build<br />
■ Tintable<br />
■ Easy Sanding<br />
VERSAPRIME 2K<br />
COLOR GALLON QUART HALF-PINT<br />
Gray APR-12611 APR-12614<br />
Buff APR-12631 APR-12634<br />
Tintable APR-12621 APR-12624<br />
Catalyst BPR-12604 BPR-12606<br />
SUPERBUILD 2K<br />
COLOR GALLON QUART HALF-PINT<br />
Gray APR-12921 APR-12924<br />
Buff APR-12911 APR-12914<br />
Tintable APR-12901 APR-12904<br />
Catalyst APR-12904 APR-12906<br />
AXIS Performance Coatings is dedicated to<br />
offering quality products that meet or<br />
succeed the high standards of today’s<br />
professional painters.<br />
Orange City, Iowa 51041 Tel. 1.866.637.8418 Fax 712.737.4997<br />
www.vogelautomotive.<strong>com</strong>
VERSAPRIME 2K<br />
SUPERBUILD 2K<br />
Ultra High Build 2K Primer Systems<br />
PRODUCT SPECIFICATIONS<br />
DESCRIPTION<br />
VERSAPRIME 2K HB and SUPERBUILD 2K are premium, ultra<br />
high build 2K-primer systems with excellent color holdout and<br />
no shrinkage. They <strong>com</strong>e in three colors: Gray, Buff and<br />
Tintable. In addition, they have fast recoat and sand times,<br />
allowing fast productivity at the shop. These primers are also<br />
<strong>com</strong>patible with any refinishing system on the market.<br />
APPLICATION / MIX RATIO - 4:1<br />
MIX RATIO - GRAY & BUFF: Mix (4:1) - To four (4) parts<br />
of VERSAPRIME 2K HB or SUPERBUILD 2K, add one (1) part<br />
of VERSAPRIME 2K HB or SUPERBUILD 2K catalyst. You may<br />
add up to 10% Acrylic Urethane or Low VOC Urethane<br />
Reducer to improve flow. To avoid moisture contamination of<br />
the catalyst, use our CATALYST GUARD. Store below 120º F<br />
(49º C). Stir <strong>com</strong>ponents thoroughly before use.<br />
MIX RATIO - TINTABLE (ONLY): Mix (4:1:1) - To four (4)<br />
parts of VERSAPRIME 2K HB or SUPERBUILD 2K, add one<br />
(1) part of VERSAPRIME 2K HB or SUPERBUILD 2K catalyst,<br />
and one (1) part of TINT-A-PRIME tint.<br />
APPLICATION: Apply two to three medium wet coats<br />
allowing 10 minutes of flash time between coats, until desired<br />
build is achieved. Film build is approximately 2.0 to 2.5 mils<br />
per coat (dry to film build). If spot priming, for best results<br />
apply first coat of VERSAPRIME 2K HB or SUPERBUILD 2K<br />
starting with the outer edge, working yourself towards the<br />
center of the repair. Allow a minimum of one hour dry time<br />
before sanding and top coating. Low temperature and/or high<br />
humidity can affect dry time.<br />
DRY TIMES:<br />
TEMPERATURE 50ºF 70ºF 90ºF 140º for<br />
(10ºC) (20ºC) (32ºC) 30-45 min.<br />
TO SAND/TOP COAT 2 hrs. 60 min. 45 min. 15 min.<br />
ACCELERATED 1.5 hrs. 45 min. 30 min.<br />
with ACH-10008<br />
SPRAY GUN SETUP:<br />
GUN TYPE FLUID TIP PRESSURE<br />
Gravity HVLP 1.9 - 2.1 mm 7-10 PSI at the cap<br />
Siphon HVLP 1.9 - 2.1 mm 10 PSI at the cap<br />
Conventional 2.0 - 2.1 mm 45-55 PSI at the gun<br />
PRODUCT SAFETY INFORMATION:<br />
Consult Material Safety <strong>Data</strong> <strong>Sheet</strong><br />
INSTRUCTIONS<br />
Before sanding, wash all surfaces thoroughly with soap and<br />
water. Rinse well and dry with a clean cloth. Clean the area<br />
with AXIS PRE-CLEAN and wipe dry with a clean cloth. Sand<br />
area as needed with 150-220 grit paper to remove any<br />
corrosion. Aluminum and stainless steel must be sanded with<br />
180-220 grit paper. Wipe all sanded areas with AXIS PRE-<br />
CLEAN and wipe dry with a clean cloth. Apply AXIS EPOX-<br />
PRIME & SEAL, SELF-ETCHING PRIMER 1K or (1:1) WC<br />
PRE-TREATMENT where needed.<br />
SUBSTRATES<br />
After being properly sanded and treated:<br />
• OEM and aftermarket finishes, excluding acrylic lacquer<br />
• Fiberglass, steel, aluminum, galvanized<br />
• Body filler, some plastics<br />
TECHNICAL<br />
VERSAPRIME 2K<br />
Color<br />
Gray, Buff & Tintable<br />
Pot Life<br />
2 hours<br />
Mix Ratio<br />
4:1 or 4:1:1 (Tintable Only)<br />
Sprayable Viscosity (RTS) 30 to 35" #3 Zahn Cup<br />
Weight Solids (RTS) 63.5%<br />
VOC Content (RTS)