Respironics BIPAP Auto SV - Impact Biomedical Corp.

More documents

Recommendations

Info

7-8 7.5 Alarm Summary Tables The following tables summarize the patient, system, and power alarm information. Patient Alarms Alarm LED Indicator Display Message Audible Indicator Device Action Possible Cause Patient Action Provider Action Apnea Red flash ALARM and APNEA flash • • • • • Operates Apnea event occurred during therapy. Press the RESET button to reset the alarm. Report the alarm to your health care professional. Continue using your device. Verify patient status. Patient Disconnect Red flash ALARM and PATIENT flash • • • • • Operates Patient circuit is Press the RESET disconnected or button to reset has a large leak. the alarm. Reconnect the patient circuit or correct the leak. If the alarm continues, contact your health care professional. Reconnect the patient circuit or fix the leak. If the alarm continues, contact an authorized service representative or Respironics to have the device serviced. Low Minute Ventilation Red flash ALARM and MinVent flash • • • • • Operates The calculated minute ventilation is less than or equal to the alarm setting. Press the RESET button to reset the alarm. Report the alarm to your health care professional. Continue using your device. Verify patient status. Provider Manual
7-9 System Alarms Alarm System Error LED Indicator Red flash Display Message ALARM flashes and system error code ("Exx") displays Card Error Yellow solid CARD flashes and card error code ("Cxx") displays Pressure Regulation High Pressure Regulation Low Red flash Red flash ALARM and cm H 2 O flash ALARM and cm H 2 O flash Audible Indicator • • • • • Device Action Possible Cause Patient Action Provider Action Shuts down and blower cannot be restarted. • • Operates • • • • • If the condition occurs for 0.5 seconds, the unit cycles to EPAP. After 3 seconds, if the condition continues, a high priority alarm is generated, but the unit still operates. If the condition is still detected after 10 seconds, the unit shuts down. • • • • • Operates Device failure. A problem exists with the Smart Card inserted in the SmartCard connectivity slot. The card may be inserted upside down or backwards. Malfunctioning device. Excessive leak or blockage. Press the RESET Have the device button to reset serviced by either the alarm. an authorized Remove power service from the device. representative or Restore power. If Respironics. the alarm continues to occur, contact your health care professional. Press the RESET button to reset the alarm. Confirm that the card is properly inserted. If the alarm continues to occur, remove the SmartCard from the device and contact your health care professional. Remove power from the device. Restore power. If the alarm continues to occur, call your health care professional. Press the RESET button to reset the alarm. Check for the following: dirty inlet filters, blocked air intake, excessive leak in patient circuit. If alarm continues, call your health care professional. Confirm that the card is properly inserted. If the alarm continues, replace the SmartCard. Have the device serviced by either an authorized service representative or Respironics. Check for the following: dirty inlet filters, blocked air intake, excessive leak in patient circuit. If the alarm continues, have the device serviced by either an authorized service representative or Respironics. Low Pressure Support Red flash ALARM and Operates Excessive leak • • • • • cm H 2 O flash or blockage. Press the RESET button to reset the alarm. Check for the following: dirty inlet filters, blocked air intake, excessive leak in patient circuit. If alarm continues, call your health care professional. Check for the following: dirty inlet filters, blocked air intake, excessive leak in patient circuit. If the alarm continues, have the device serviced by either an authorized service representative or Respironics. Prescription Complete Yellow solid ALARM, CARD and cm H 2 O flash • • Operates Prescription SmartCard has been inserted into the device. Press the RESET button to reset the alarm. Remove the SmartCard from the device. Remove the SmartCard to exit this screen and return to the previous screen. Provider Manual
Page 1 and 2: autoSV TM with Encore SmartCard ®
Page 3 and 4: Table of Contents Chapter 1: Packag
Page 5 and 6: 1-1 Chapter 1: Package Contents BiP
Page 7 and 8: 2-1 Chapter 2: Warnings and Caution
Page 9 and 10: 2-3 2.2 Cautions • The device may
Page 11 and 12: 3-1 Chapter 3: Introduction 3.1 Ove
Page 13 and 14: 3-3 IPAP max Pressure IPAP min EPAP
Page 15 and 16: 3-5 3.2.3 Ramp The device is equipp
Page 17 and 18: 3-7 Maximum IPAP Time (IPAP to EPAP
Page 19 and 20: 3-9 3.4 Definitions, Acronyms, and
Page 21 and 22: 4-1 Chapter 4: Controls and Display
Page 23 and 24: 4-3 4.1.2 Control Buttons The contr
Page 25 and 26: 4-5 4.2.1 LED Backlight for Buttons
Page 27 and 28: 5-1 Chapter 5: Setup 5.1 Preparing
Page 29 and 30: 5-3 Figure 5-3 Using the External P
Page 31 and 32: 5-5 The Standby screen appears when
Page 33 and 34: 6-1 Chapter 6: Changing Settings Th
Page 35 and 36: 6-3 3. IPAP Max Setting Screen The
Page 37 and 38: 6-5 8. Ramp Start Pressure Setting
Page 39 and 40: 6-7 13. LED Backlight Setting Scree
Page 41 and 42: 6-9 2. Respiratory Rate Screen This
Page 43 and 44: 7-1 Chapter 7: Alarms This chapter
Page 45 and 46: 7-3 7.2 System Alarms The device ha
Page 47 and 48: 7-5 7.3 Patient Alarms The device h
Page 49: 7.4 Power Alarms The device has the
Page 53 and 54: 8-1 Chapter 8: Cleaning and Mainten
Page 55 and 56: 9-1 Chapter 9: Adding Supplemental
Page 57 and 58: 10-1 Chapter 10: Circuits and Acces
Page 59 and 60: 11-1 Chapter 11: Operational Verifi
Page 61 and 62: 12-1 Chapter 12: Specifications Env
Page 63 and 64: 12-3 Triggers and Cycles Patient In
Page 65 and 66: A-1 Appendix A: Error Codes This ap
Page 67 and 68: A-3 E61 E62 E63 E64 E65 E66 E67 E68
Page 69 and 70: B-1 Appendix B: EMC Information Gui
Page 71 and 72: Limited Warranty Respironics, Inc.

Respironics BIPAP Auto SV - Impact Biomedical Corp.

Create successful ePaper yourself

Delete template?

Save as template?