EDX Product Brochure - Evapco

OPTIONAL EQUIPMENT
Single Side Inlet Connection
The EDX is available with a Single Side Inlet option which eliminates
external pipework, valves and field balancing associated
with the standard (2) inlet design.
Internal PVC pipework is utilized to relocate the water inlet to the
side of each cell. The connection is standard with a hole and bolt
circle pattern, other options are available. Note: Multiple cell
installation will require adequate space between towers to allow
for piping, unless the bottom inlet option is selected.
If a tight, side by side layout is required, the EDX is available with
an optional Bottom Inlet Connection. The inlet is located on the
bottom of the cold water basin and allows the inlet pipework to
run underneath the unit. Note: Adequate space is required
underneath the unit for pipework. Please consult the factory for
certified drawings indicating connection size and location.
S
K
Model Static Single P Water Inlet* Water Outlet**
No. Lift Inlet Height (Per Cell) (Per Cell)
EDX 212-0122 17' 5” 8'-8-3/8” 11' 1” (1) 12” (1) 12”
EDX 212-0222 23' 9-3/4” 14' 7-1/4” 11' 1” (1) 12” (1) 12”
EDX 212-0322 19'- 4-1/2” 10' 8” 11' 1” (1) 12” (1) 12”
EDX 212-0422 17' 5” 8' 8-3/8” 11' 1” (1) 12” (1) 12”
EDX 212-0522 23' 9-3/4” 14' 7-1/4” 11' 1” (1) 12” (1) 12”
EDX 212-0622 19' 4-1/2” 10' 8” 11' 1” (1) 12” (1) 12”
EDX 212-0722 17' 5” 8' 8-3/8” 11' 1” (1) 12” (1) 12”
EDX 212-0822 23' 9-3/4” 14' 7-/4” 11' 1” (1) 12” (1) 12”
EDX 212-0922 19' 4-1/2” 10' 8” 11' 1” (1) 12” (1) 12”
EDX 212-1022 23' 9-3/4” 14' 7-1/4” 11' 1” (1) 12” (1) 12”
EDX 214-0124 17' 7-3/8” 8' 8-3/8” 12' 1” (1) 14” (1) 14”
EDX 214-0224 19' 6-7/8” 10' 8” 12' 1” (1) 14” (1) 14”
EDX 214-0324 17' 7-3/8” 8' 8-3/8” 12' 1” (1) 14” (1) 14”
EDX 214-0424 19' 6-7/8” 10' 8” 12' 1” (1) 14” (1) 14”
EDX 214-0524 17' 7-3/8” 8' 8-3/8” 12' 1” (1) 14” (1) 14”
EDX 214-0624 19' 6-7/8” 10' 8” 12' 1” (1) 14” (1) 14”
EDX 214-0724 17' 7-3/8” 8' 8-3/8” 12' 1” (1) 14” (1) 14”
EDX 214-0824 24' 1/8” 14' 7-1/4” 12' 1” (1) 14” (1) 14”
EDX 214-0924 19' 6-7/8” 10' 8” 12' 1” (1) 14” (1) 14”
EDX 214-1024 17' 7-3/8” 8' 8-3/8” 12' 1” (1) 14” (1) 14”
EDX 214-1124 19' 6-7/8” 10' 8” 12' 1” (1) 14” (1) 14”
EDX 214-1224 24' 1/8” 14' 7-1/4” 12' 1” (1) 14” (1) 14”
EDX 214-1324 24' 1/8” 14' 7-1/4” 12' 1” (1) 14” (1) 14”
EDX 214-1424 19' 6-7/8” 10' 8” 12' 1” (1) 14” (1) 14”
EDX 214-1524 24' 1/8” 14' 7-1/4” 12' 1” (1) 14” (1) 14”
Notes:
1. Use this chart for the pre-engineering phase of the project. Obtain factory certified drawings from your local EVAPCO representative or the factory.
2. Pipework shown is provided by EVAPCO. Consult the factory certified drawings for dimensions.
3. External pipework not shown must be provided by others and self-supported. Do not support pipework from the cooling tower.
4. Note: The single inlet connection is located above the basin access door, position inlet piping properly to avoid blocking the door. Consult page 5 for
dimensions of the unit.
5. Consult the factory for optional bottom inlet connection.
* Standard connection is hole and bolt circle design for 150# raised face flange.
** Standard connection is Beveled for Weld and grooved for a mechanical coupling.
Other Accessories/Optional Materials
• Pony Motors
• Bottom Sump Box
• Gear Drive
• Air Inlet Screens
• Electric Water Level Controls and Level Indicators
• Vibration Switch
• Fan and Motor Davit
• Flanged Connections
• Flume Plate
Models
KW*
EDX 212-0122 to 1022 (4) 12
EDX 214-0124 to 1524 (4) 15
Electric Pan Heaters
9