Instruction Manual - Cole-Parmer

More documents

Recommendations

Info

1.2 Inserting Batteries NOTE: Please ensure that the gasket is in place otherwise the instrument will not be waterproof. Power up your meter using either: 1. Four ‘AA’ size 1.5 V alkaline batteries (supplied) or, 2. 9V DC power adapter (Optional in some models). 1.2.1 Inserting batteries for the first time 1. Use a Phillips screw driver to remove the four screws holding the battery cover. 2. Insert the batteries in the right direction. 3. Replace the battery cover and screws. Note the ▲UP symbol marked on the cover. 4. Press the ON (F4) key. Hold the key down until the display appears. 5. Set the system date & time before you start operating the meter for the first time. 1.2.2 Changing batteries subsequently 1. Connect the adapter before changing the batteries. 2. If DC adapter is not available, switch off the meter and change the batteries within 30 seconds to avoid resetting the clock. This prevents the system time from resetting automatically. 4
1.3 Attaching the Belt To attach the safety belt: 1. Use a Phillips screw driver to remove the four screws holding the battery cover. 2. Insert the safety belt through the two slots as indicated below. 3. Screw the battery cover back on. Note the ▲UP symbol marked on the cover. 4. Insert your palm between the belt and the body of the meter and adjust the hook & loop fastener. Note the correct side of the belt Battery Cover Hook & Loop fastener 5
Page 1: Integrated Instruction Manual WP 60
Page 5 and 6: Table of Contents GENERAL GUIDE....
Page 7 and 8: 2.9 Calibration Report ............
Page 9: GENERAL GUIDE This section is appli
Page 14 and 15: 1.4 Connecting Peripherals 1.4.1 Pr
Page 16 and 17: 2. System Setup Mode For All Meters
Page 18 and 19: System setup sub-group allows you t
Page 20 and 21: ON Time Back Light (permanently ON)
Page 22 and 23: Protection Set Pass Word calibratio
Page 24 and 25: Note: You can enter ‘00000’ (re
Page 26 and 27: It is recommended that you perform
Page 29 and 30: 4. Measurement Mode For All Meters
Page 31 and 32: 4.2.3 Stable reading indicator You
Page 33 and 34: 5.2.1 Logging data automatically in
Page 35 and 36: Transfer Stored data to CyberComm 5
Page 37 and 38: 6. Technical Specifications Tempera
Page 39 and 40: Resistivity Range Measuring ranges
Page 41 and 42: 7. Accessories Eutech Instruments P
Page 43 and 44: damage during shipment, and insured
Page 46 and 47: 1. Temperature Setup Temperature se
Page 48: 2.3 Temperature Calibration for MTC
Page 52 and 53: 1. pH Setup pH setup sub-group allo
Page 54 and 55: Buffer First Point of Calibration O
Page 56 and 57: 2.4 pH Calibration with a User-defi
Page 58 and 59: NEXT (F3) ESC (F4) ENTER Goes to pH
Page 60: mV PARAMETER GUIDE 1. mV Setup Mode
Page 63 and 64:
7. Press ESC (F4) to go to measurem
Page 66:
ION PARAMETER GUIDE 1. Ion Setup Mo
Page 69 and 70:
Use standard solutions of 0.001, 0.
Page 71 and 72:
3. Ion Measurement Mode In Ion meas
Page 74 and 75:
1. Conductivity Setup Conductivity
Page 76 and 77:
2. Conductivity Calibration Mode 2.
Page 78 and 79:
2.7 Manual Calibration Note: If you
Page 80 and 81:
2.9 Calibration Report Calibration
Page 82 and 83:
- END OF CONDUCTIVITY SECTION - 74
Page 85 and 86:
1. TDS Setup The TDS setup screen p
Page 87 and 88:
2. TDS Calibration Mode You can com
Page 89 and 90:
3. TDS Measurement Mode In TDS meas
Page 91:
SALINITY PARAMETER GUIDE 1.Salinity
Page 94 and 95:
Salinity Settings Page 2 - Hi-Lo Se
Page 96 and 97:
2.1 Salinity Calibration Report Cal
Page 99:
RESISTIVITY PARAMETER GUIDE 1.Resis
Page 102 and 103:
Resistivity Settings Page 2 - Hi-Lo
Page 104 and 105:
Note: The function of the keys avai
Page 107 and 108:
DISSOLVED OXYGEN PARAMETER GUIDE PA
Page 109 and 110:
PART A - % Saturation Mode 1. O2 %
Page 111 and 112:
disabled) 2. DO Calibration in % Sa
Page 113 and 114:
Function Keys available in saturati
Page 115 and 116:
2.4 % Saturation Offset Adjustment
Page 117 and 118:
Figure 56 : DO (mg/L) - Page 1 This
Page 119 and 120:
2. DO Calibration in mg/L mode or p
Page 121 and 122:
Figure 60 : DO Calibration Report i
Page 123 and 124:
Since the DO in the sample is consu
Page 125 and 126:
10. Using the installation tool, sc
Page 127:
For more information on Eutech Inst
show all

Instruction Manual - Cole-Parmer

Create successful ePaper yourself

Delete template?

Save as template?