Christie Entero Projector and Cube Installation Manual

More documents

Recommendations

Info

A.4 CC72 Specifications WUXGA Product cube CC72-3301 make-up 1 projection engine RPMWU-LED01 screen options SC72-XP01 Imaging imaging P technologies native resolution illumination Pixel density pitch Screen gap types W Inputs standard scan rates expansion optional modules compatibility CCipcfQX Illumination technology LED life rating 2 Color temperature range gamut adjustment and control Optical lens type ff brightness uniformity contrast ratio 3 Control/ networking ports/controls Upgradability software Optional inputs accessories other Wi Physical dimensions characteristics weight (approx.) Sc shipping weight Sc (approx.) stackability service type Environment Sc operating temperature 4 non-operating temperature humidity altitude Power rating voltage (projection current engine) consumption dissipation (maximum) Reliability and MTBF serviceability MTTR Regulatory (projection engine) Calibration Limited warranty Additional features and benefits W ’ 1 2 3 p 4 , A-8 Entero Projector and Cube Installation Manual 020-100839-01 Rev. 2 (04-2013)
A.4.1 CC72 Brightness and Performance Characteristics Engine option Screen option Screen type Viewability Screen 1/2 gain Brightness 1 Horiz. Verti. Horiz. Verti. (cd/m 2 ) WUXGA RPMWU-LED01 SC72-XP01 r 1 rr Entero Projector and Cube Installation Manual A-9 020-100839-01 Rev. 2(04-2013)
Page 1:
Projection Engines Entero RPMSP-LED
Page 5 and 6:
NOTICES COPYRIGHT AND TRADEMARKS ©
Page 7 and 8:
Table of Contents 1: Introduction 1
Page 9:
Table of Contents 5.10 Portions of
Page 12 and 13:
NOTICES: Failure to comply with th
Page 14 and 15:
2.3 Components and Hardware All maj
Page 16 and 17:
2.4 Unpack Cube Enclosures and Pede
Page 18 and 19:
3 2 2 2 3 2 4 1 1 1 1 5 1 Use to fa
Page 20 and 21:
2.7 Install Display Cube Enclosures
Page 22 and 23:
3. Loosen each of the adjustment sc
Page 24 and 25:
2.8.2 Lag Bolt Application Each col
Page 26 and 27:
. For vertical adjustment: Insert 2
Page 28 and 29: 3.3 Projector Components 3 4 2 1 1
Page 30 and 31: Remove Tape and Loosen Securing Bol
Page 32 and 33: 5. Turn the adjuster 180°. 6. Alig
Page 34 and 35: 3.6.2 Connect the PHM to the EM and
Page 36 and 37: Mixed Network In the illustrated mi
Page 38 and 39: Mixed Serial Network (RS232 and RS4
Page 40 and 41: 3.7.2 ArrayLOC Over PHM Network In
Page 42 and 43: Calculate Hardware Requirements In
Page 44 and 45: 3.7.4 Enable ArrayLOC If using proj
Page 46 and 47: 3.8.4 Analog BNC Input Card This ca
Page 48 and 49: 3.9 System Integration - GPIO Conne
Page 50 and 51: 4.3 Focus .64:1 Fixed Lens The focu
Page 52 and 53: NOTES: 1) If it is necessary to mak
Page 54 and 55: 4.5.1 Mirror Adjustment Screws Turn
Page 56 and 57: Image Problem Screws to Adjust A1 D
Page 58 and 59: For information about managing chan
Page 61 and 62: 5 Troubleshooting NOTICE: To avoid
Page 63 and 64: SP 06 LM Air inlet overtemp or sens
Page 65 and 66: 5.9 The Upper Portion of the Displa
Page 67 and 68: 6 Maintenance The following procedu
Page 69: 6.4 Clean the Projection Lens NOTIC
Page 72 and 73: A.1 CC50 Specifications SXGA+ Produ
Page 74 and 75: A.2 CC67 Specifications SXGA+ Produ
Page 76 and 77: A.3 CC70 Specifications WUXGA Produ
Page 81 and 82: *000-103704-01* ASSY TECH DOCS Ente
show all

Christie Entero Projector and Cube Installation Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?