使用说明 - Rosenberger
使用说明 - Rosenberger
使用说明 - Rosenberger
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Instruction<br />
MA_60W110-C03<br />
Manual of 1/2"R Ring Corrugated Cable Stripping Tool Revision d 25.08.2009<br />
Stripping tool and it’s functional parts(Please<br />
refer to picture right side)<br />
<br />
<br />
Adjustment tools: 2.5#, 1.5# inner hexagon<br />
spanner.<br />
2.5 1.5 <br />
Handle <br />
Wimble <br />
Blade2 <br />
Screw <br />
Stripping assistant tools: Hacksaw, knife,<br />
rasper , pliers.<br />
<br />
Adjust position of blade according to stripping<br />
requirement:<br />
Because there’s dimension distinction between different<br />
manufacturers’ cables, if necessary please adjust the position of<br />
blades.<br />
Blade1: adjusted by washer<br />
Blade2: adjusted by screw<br />
Blade2 <br />
Blade1 <br />
Tool body <br />
Screw <br />
(need 1.5# spanner)<br />
<br />
<br />
<br />
<br />
<br />
Washer <br />
(need 2.5# spanner)<br />
Blade1 <br />
Using electric drill<br />
Remove the handle then insert the end into the drill (Please<br />
refer to picture right side), and please use low spin speed.<br />
<br />
<br />
<br />
Step<br />
<br />
Operation Instruction<br />
<br />
Chart<br />
<br />
Notice<br />
<br />
1<br />
Cut off the cable and straighten the<br />
end for 200mm.<br />
200mm<br />
Please cut the cable by<br />
hacksaw.<br />
<br />
2<br />
1) Insert cable into stripping tool.<br />
2) Rotate the handle while pressing the<br />
tool to cable’s direction until the cable<br />
spins loosely in the stripping tool.<br />
1) <br />
2) <br />
<br />
Be careful since the sharp<br />
outer conductor and blade<br />
may cause several bodily<br />
injury! Always wear<br />
protective gloves and don’t<br />
insert the finger into the<br />
tool.
Instruction<br />
3<br />
If cable’s outer conductor is not cut off<br />
at it’s corrugation ridge, cut the inner<br />
conductor by pliers for a length ”a”<br />
Distance between the end surface to<br />
corrugation ridge. Then go back to<br />
step 2.<br />
<br />
<br />
a<br />
2 <br />
a<br />
a<br />
If there’s dielectric on the<br />
inner conductor, remove it<br />
by knife.<br />
Be careful NOT to hurt the<br />
inner conductor.<br />
<br />
<br />
<br />
<br />
4<br />
Compare with the gauge on the tool<br />
and check whether the stripping<br />
dimension have been got properly.<br />
<br />
<br />
<br />
-like this<br />
5<br />
Proper dimension and shape.<br />
<br />
14.5 +0.5<br />
70.3<br />
C0.4<br />
Use rasper to flattening the<br />
end of center contact to assure<br />
proper length and chamfering.<br />
<br />
<br />
<br />
<br />
Corrugation ridge <br />
6<br />
Insert cable’s inner conductor into<br />
stripping tool’s lateral hole, then rotate<br />
the tool to flare outer conductor.<br />
<br />
<br />
Connector’s<br />
back nut<br />
<br />
Notice: This step should be<br />
done after the operation that<br />
slide the connector ‘s back nut<br />
and clamp ring onto cable.<br />
More related information refer<br />
to assembly instruction of the<br />
connector.<br />
<br />
<br />
<br />
<br />
Declaration:<br />
1. ROSENBERGER disclaims any responsibility for the result of improper usage.<br />
2. Information in this instruction is subject to change without notice.<br />
<br />
<br />
<br />
Draft Checker Approved Date Rev. Engineering change number Name Date<br />
Jeff Roger Kevin 28/09/09 d 09-0426 Chen XW 25.08.2009<br />
<strong>Rosenberger</strong> Hochfrequenztechnik GmbH & Co. KG, Germany<br />
<strong>Rosenberger</strong> Asia Pacific Electronic Co., Ltd., China<br />
Tel.: +49 8684 18-0 Fax: +49 8684 18-499 Tel.: +86 10 80481995 Fax: +86 10 80497052<br />
www.rosenberger.de email: info@rosenberger.de www.rosenbergerap.com email: info@rosenbergerap.com