EASYBuS - Iberica de Automatismos

More documents

Recommendations

Info

EASYBus-display and monitoring device for 20 channels Front 48 x 96 EB 3000 Specification E.A.S.Y.Bus - Modul Display range: -1999 to +9999 digit Resolution: automatic detection of resolution and decimal point of connected sensor modules. Accuracy: depending on sensor module used. The EB3000 transfers this value digitally without any additional fault. Sensor modules: (not included in scope of supply) all intelligent EASYBus sensor modules as well as EASYLOG can be connected. 2-wire connection in ring-, tree- or star type. No polarity. Sensor supply: via EB 3000 max. bus load: 30 EASYBus standard loads max. meas. channels: 20 perm. cable length: 500 m (depending on type of cable and wiring) Switching outputs: 4 relay outputs (make contact), switching to common terminal. Outputs can be assigned to any channel Switching power: 230VAC, 5A, ohm resistive load Switching function: 2-point controller, 2-point controller inverting Switching points and delay for each output freely selectable Alarm output: 1 relay output (change-over contacts) Switching power: 230VAC, 5A, ohm resistive load Alarm function: Common alarm for all sensors. Alarm-settings of the sensors changeable. Configuration: All standard-functions can be entered and controlled via keypad. A confi guration software is available for extended confi guration (supported converter is needed). Min./Max. value memory: from all connected sensor modules the max. and min. value are callable via front-side keypad. Calculation-functions: there are 2 “virtual” channels additionally to the sensor-channels. A calculated value can be displayed here. Possible calculation functions: sensor-deviation, averaging above x sensors, etc. Self diagnosis: permanent self-diagnosis to ensure trouble-free function. A corresponding fault massages will shown at an error (e.g. sensor damage, ..) Display: 4-digit, red, 13mm high LED-display (meas. value), 2-digit, red, 7mm high LED-display (channel display). 11 additional LEDs to display the unit, switching state or alarm Interface: EASYBus-interface with supported converter (e.g. EBW1) GRS232 compatible, for communication with a PC. Housing: rack-type housing 48 x 96 x 100mm (H x W x D). Front: Transparent membrane keyboard IP65. Sealing for housing for installation according to IP65 will have to be ordered separately. Panel cutout: 43 x 90,5 mm (H x W). Connection terminals: screw-type/plug-in terminals Ambient temperature: -25 to 50°C (permissible ambient temperature) Voltage supply: 230V AC 50/60Hz Power consumption: approx. 9 VA • Up to 20 sensor-modules or loggers can be connected • Sensor module supply and data transfer are carried out via one single 2-wire line. No additional voltage supply for sensor modules required. • 5 relay outputs (4 x controlling, 1 x alarm) • Controller functions can be assigned to any channel, e.g.: - 4 x two-point-controllers (of 4 arbitrary sensors) - 2 x three-point-controllers (of 2 arbitrary sensors) - 4-way switch (of 1 arbitrary sensor), .... • 2 calculated channels for displaying: - average value over more sensors - difference of 2 sensors - special functions • Min-/Max- value memory from all sensors callable • Alarm monitoring for all connected sensors • easy confi guration via front-side keypad or via interface • Via serial interface the connected devices can be read or additionally be monitored with a PC. • With EASYBus interface to the PC: - Up to 1000m cable-length from PC to EB3000 possible (with interface converter EBW64 or EBW240) - Additional connection of EASYBus-modules that are not monitored or connection of a second EB3000 on the same converter possible. The EB 3000 device - cost savings in all areas ! • Short installation time - only one 2-pin line. • polarity must not be observed by installation • Minimum material requirement - only one display and monitoring device for up to 20 sensor modules • Minimum time requirement for planning and commissioning - automatic sensor module detection, expandable for up to 20 sensor modules of any type. Accessories GGD 4896 add. sealing for panel mounting acc. to IP65 Sensor, logger modules p.r.t. page 44, 47 - 50, 60 - 63, 68 -71 for temperature, humidity, norm. signal, frequency, ... EBW 1 interface converter: EASYBUS to RS232 EBSK 01 connection cable 1m, for EASYLOG, EBN, ... VSL 2P twisted special cable per m for EASYBus-system, cross section 2 x 0,75 mm² AKL 1P special-branch terminal or connection to VSL2P, 2 pieces EASYBus-Configurator free of charge software for comfortable editing of all EB3000-parameters. (downloadable from our homepage: Service --> Download) Alarm / Protection Temperature probe Transmitter Logger / EASYBus Display / Controller Handheld instrument 73
Handheld instrument Display / Controller Logger / EASYBus EASYBus - interface converter EBW 1 EBW 2 EBW 3 N E W EBW 64 interface converter for connection of max. 9 EASYBus-modules to the RS232-interface (9-pin Dsub) of your PC. Scope of supply: interface converter, 9-pin Dsub extension cable main supply independent interface converter for connection of one EASYBus-module (e.g. EASYLOG ) to the RS232- interface (9-pin Dsub) of your PC. (Power supply via integrated 9V-battery) Scope of supply: interface converter incl. 9V-battery, 9-pin Dsub extension cable interface converter for connection of one EASYBus-module (e.g. EASYLOG ) to the USBinterface of your PC. (Power supply: via USB) Scope of supply: interface converter interface converter for connection of max. 64 EASYBus-modules to the RS232-interface of your PC. Scope of supply: interface converter, 9-pin Dsub extension cable EBW 240 incl. software EASYControl interface converter for connection of max. 240 EASYBus-modules to the RS232-interface of your PC. Scope of supply: interface converter, plug-in power adapter, 9-pin Dsub extension cable, software EASYControl. Transmitter Temperature probe Alarm / Protection Specification: EBW 1 EBW 2 EBW 3 EBW 64 EBW 240 Voltage supply: 230 V AC / 50Hz 9 V - battery not necessary 230 V AC / 50Hz 230 V AC / 50Hz (over power adapter) Power consumption: approx. 5 W max. 1 W max. 0.5 W approx. 15 W approx. 30 W Max. permissible sensor modules *: 9 1 1 64 240 Permissible cable length **: 200 m 10 m 10 m 1000 m 1000 m Baud rate: 4800 Baud Serial connection: RS232 RS232 USB RS232 RS232 Electrical isolated: yes no yes yes yes Overload display: no no no yes yes Short-circuit proof: yes yes yes yes yes Operating temperature: 0 ... 50 °C 0 ... 50 °C -25 ... 50 °C 0 ... 50 °C 0 ... 55 °C Humidity: 20 ... 80 %RH, non-condensing Storage temperature: -20 ...+70 °C -20 ...+70 °C -25 ...+70 °C -20 ...+70 °C -20 ...+60 °C Dimensions (H x W x D): 112 x 80 x 45 mm 107 x 62 x 26 mm 56 x 31 x 24 mm 100 x 75 x 110 mm 200 x 240 x 55 mm (without power adapter) * depending on type of the used sensor modules ** depending on type of cable and wiring Interface accessories USB-Adapter for connection of an interface converter to the USB-interface of yout PC GRS 02/9 interface cable fotEBW 2 for connection to a MODEM ... GSA 9S-25B connection-adapter: 9-pin Dsub-plug 25-pin Dsub-socket Note: the EASYBus-monitoring device EB2000 should be can used as a converter for max. 9 sensor modules. 74
Page 1 and 2: Handheld instrument Display / Contr
Page 3 and 4: Alarm / Protection Temperature prob
Page 5 and 6: Handheld instrument EASYBus - senso
Page 7: Temperature probe Transmitter Logge
Page 11 and 12: Handheld instrument EASYBus - compo

EASYBuS - Iberica de Automatismos

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?