Regency IG35 owners & instal manual.pdf
Regency IG35 owners & instal manual.pdf
Regency IG35 owners & instal manual.pdf
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
INSTALLATION<br />
FLUEING<br />
THE APPLIANCE MUST NOT BE CONNECTED<br />
TO A CHIMNEY FLUE SERVING A SEPARATE<br />
SOLID FUEL BURNING APPLIANCE.<br />
This appliance is designed to attach to a 100<br />
mm diameter twin skin or listed gas fuel type<br />
fl ue liner running the full length of the chimney. A<br />
minimum fl ue height of 1.5 m. is recommended.<br />
The <strong>Regency</strong> Inbuilt Fireplace incorporates<br />
its own internal draft diverter, so no additional<br />
external draft diverter is required.<br />
Periodically check that the fl ue is unrestricted<br />
and an adequate draft is present when the unit<br />
is in operation.<br />
GAS PIPE PRESSURE<br />
TESTING<br />
The appliance must be isolated from the gas<br />
supply piping system by closing its individual<br />
<strong>manual</strong> shut-off valve during any pressure<br />
testing of the gas supply piping system at<br />
test pressures equal to or less than 1/2 psig.<br />
(3.45 kPa). Disconnect piping from valve at<br />
pressures over 3.45 kPa (14" w.c.).<br />
The manifold pressure is controlled by a<br />
regulator built into the gas control, and should<br />
be checked at the pressure test point.<br />
Note:<br />
To properly check gas pressure,<br />
both inlet and manifold pressures<br />
should be checked using the valve<br />
pressure ports on the valve.<br />
S.I.T. Valve Description<br />
1) On-Off Solenoid Valve EV1<br />
2) On-Off Solenoid Valve EV2<br />
3) Inlet Pressure Test Point<br />
4) Outlet Pressure Test Point<br />
5) Connection for Pressure Regulator/<br />
Combustion Chamber Compensation<br />
6) Pressure Regulator for Minimum and<br />
Maximum Outlet Pressure<br />
7) Gas Outlet Pressure Electric Modulator<br />
8) Pilot Outlet<br />
9) Main Gas Outlet<br />
10) Side Outlet<br />
Before <strong>instal</strong>ling fl ue system ensure that the<br />
damper plate is open and secure to prevent the<br />
damper plate from falling down and crushing<br />
the liner.<br />
Install to AS5601-2004,(Australia) NZS 5261<br />
(New Zealand).<br />
Combustion and Ventilation Air<br />
WARNING: This appliance needs<br />
fresh air for safe operation and must<br />
be <strong>instal</strong>led with provisions for adequate<br />
combustion and ventilation<br />
air available to the room in which it<br />
is to be operating.<br />
Air for combustion is drawn in through the front<br />
of the unit, therefore, the front of the unit must<br />
be kept clear of any obstructions.<br />
1) Make sure the valve is in the "OFF"<br />
position.<br />
2) Loosen the "IN" (# 3) and/or "OUT" (# 4)<br />
pressure tap(s), turning counterclockwise<br />
with a 1/8" wide fl at screwdriver.<br />
3) Attach manometer to "IN" and/or "OUT"<br />
pressure tap(s) using a 5/16" (8mm) ID<br />
hose.<br />
4) Seal and or check the pilot outlet (# 8)<br />
5) The pressure check should be carried out<br />
with the unit burning and the setting should<br />
be within the limits specifi ed on the safety<br />
label.<br />
6) When fi nished reading manometer, turn<br />
off the gas valve, disconnect the hose and<br />
tighten the screw (clockwise) with a 1/8"<br />
fl at screwdriver. Screw should be snug,<br />
but do not over tighten.<br />
<strong>Regency</strong> <strong>IG35</strong> Gas Inbuilt Fireplace<br />
7