MPC Microtopping - Interior-Exterior Pigmented Nominal ... - Miracote

Installation Guideline
MPC Microtopping System Pigmented
Interior /Exterior
Nominal 3/32 Inch
Step # Installation Steps Installation Methods Products & Mix Ratios Theoretical Coverage Rates
Mechanically Prepare and a. Sandblasting or Miracote MPC Micro-Topping Systems must be applied to a
Presaturate the Concrete Substrate b. Shotblasting or clean, sound, and mechanically prepared concrete substrate, N/A
1 c. Diamond grinding or as per ICRI's Technical Guide No.03732, "Selecting and
Note: Minimum (CSP) concrete surface profile d. Other similar and approved Specifying Concrete Surface Preparation". Concrete substrate
of CSP-3 or higher is required depending on mechanical methods. should be (SSD) Saturated Surface Dry with no standing
substrate conditions & coating requirements. e. Saturate with potable water water at the time of application.
Apply 1st MPC Coat a. Hand Trowel or Blend: Colorpax-LIP + MPC Liquid Catalyst +
b. Magic trowel or MPC White Regular Powder 500 SF/Unit
2 Note: ColorPax-LIP (Liquid Integral Pigment) c. Squeegee Mix Ratio = (1) ColorPax-LIP Container to
packs must be dispensed and mixed into the (1) 5 Gal. Pail MPC Liquid Catalyst to Note: Coverage can vary depending
5 Gal. pail of MPC Liquid Catalyst. (2) 55 LB Bags MPC White Regular Powder on surface profile & condition.
Apply 2nd MPC Coat a. Hand Trowel or Blend: Colorpax-LIP + MPC Liquid Catalyst +
b. Magic trowel or MPC White Regular or Smooth Powder 500 SF/Unit for Regular
3 c. Squeegee Mix Ratio = (1) ColorPax-LIP Container to 800 SF/Unit for Smooth
Note: For the 2nd coat only, mixing a 50/50
blend of Regular and Smooth MPC Powder, in
(1) 5 Gal. Pail MPC Liquid Catalyst to
(2) 55 LB Bags MPC White Regular Powder
White or Gray, is an acceptable option to or Note: Coverage can vary depending
modify desired trowelling characteristics. (1.5) 55 LB Bags MPC White Smooth Powder on surface profile & condition.
Apply 3rd MPC Coat a. Hand Trowel or Blend: Colorpax-LIP + MPC Liquid Catalyst +
b. Magic trowel or MPC White Smooth Powder
4 c. Squeegee Mix Ratio = (1) ColorPax-LIP Container to 800+ SF/Unit
(1) 5 Gal. Pail MPC Liquid Catalyst to
(1.5) 55 LB Bags MPC White Smooth Powder
For antiquing options with acid or water based stains/dyes, please review the IG's for
Mirastain I or Mirastain II.
Choose any of the Miracote sealers or topcoats for best results depending on location,
service, use and exposure. Refer to the Product Technical Data Sheets and Installation
Guideline for Miracote HDWB, HD II*, Mirapoxy WB, Mirathane WB, CQ Clear Epoxy,
Mirathane APU 100, or Glazetop.
Miracote is a registered trade name of Crossfield Products Corp.
MPC is a registered trade mark of Crossfield Products Corp. Page 1 of 2 MIR.250a IG 1208

Note:
Installation Guideline
MPC Microtopping System Pigmented
Interior /Exterior
Nominal 3/32 Inch
Prior to starting the application of any Miracote Product or System be sure to read the Installation Guideline Manual. Appendices, Product Data Sheets, MSDS and other pertinent documents
published by Crossfield Product Corp. for information, including but not limited to, Precautions, Limitations, Disclaimers and Warranties.
Pay special attention to substrate moisture content, physical condition of the substrate, method(s) of surface preparation, surface restoration, detailing of cracks, joints, transitions and terminations,
and any applicable specifications. Review carefully for unknown site conditions or defects.
The theoretical coverage rates stated in the Installation Guides are for estimating purposes only. Factors, such as, allowance for material waste, unusual or abnormal substrate conditions and other
unforeseen job site conditions that may affect actual product yields are the responsibility of the installer.
* Not available where prohibited by law, such as the Southern California AQMD. Extended lead time required.
Miracote is a registered trade name of Crossfield Products Corp.
MPC is a registered trade mark of Crossfield Products Corp. Page 2 of 2 MIR.250a IG 1208