catalog

Recommendations

Info

#91620 Saddle Rail for Remington (12-GA, 5 in) #91680 Saddle Rail for Remington with Magazine Clamp (12-GA, 20 inch) Remington saddle rails Mesa Tactical Saddle Rails are 6061-T6 aluminum brackets that wrap around the top of the shotgun receiver. The factory trigger pins are replaced by an internally threaded steel pin (in the rear) and paired Chicago screws (up front), to which both sides of the saddle rail are securely bolted. The saddle rail is Type III anodized for a rugged surface finish. Our Saddle Rail is specially contoured to allow operation of a semi-automatic bolt on the right side of the receiver, so it can be installed on Remington 1100 and Remington 11-87 semi-auto shotguns as well as Remington 870 pump shotguns. The rail is notched at the rear to accommodate Scattergun/Wilson style ghost ring sights, and extends to the front of the shotgun receiver (5 inch rail), 2¾ inches past the front of the receiver (8½ inch rail), or just beyond the barrel’s magazine lug (20 inch rail). The 20 inch rails are available with or without the required Magazine Clamp or Barrel Clamp. No gunsmithing is required to install. Minor fitting of fasteners may be necessary. See page 20 for SureShell Saddle Rails that feature a four-, six- or eight-shot SureShell aluminum shotshell carrier yoke on the left side of the receiver. #92150 Side Mount Picatinny Rail for Remington 870 (Right Side) (weapon light not included) Remington side-mount rail Recently Mesa Tactical was asked by several law enforcement agencies to produce a Picatinny rail that can be mounted on the right side of the Remington 870 and allow a weapon light to be secured behind the ejection port. This is for door breachers who need more light in tight quarters where lights near the muzzle would be unsuitable. We also offer a rail for the left side of the receiver. These rails are compatible with SureShell carriers mounted on the opposite side of the receiver. As with all our rails, these are machined to the MIL-STD 1913 specification from 6061-T6 aluminum, and features a mounting system similar to that of our SureShell aluminum shotshell carriers. 26 MESA TACTICAL CATALOG #20
Rails for drilled and tapped receivers Mesa Tactical makes Picatinny rails for several popular shotgun models that feature pre-drilled and tapped holes in the tops of their receivers. Top rails for the Remington 870 use the tactical hole pattern introduced on some tactical 870 models in the summer of 2007. Mossberg rails attach directly to the receivers of late- model (1997 and later) Mossberg pump shotguns with pre-tapped holes. The 20 inch rails are anchored at the front by a magazine clamp that features either a short length of Picatinny accessory rail at the bottom, or a sling swivel stud. The front clamp interferes with the barrel lug on 18 inch Mossberg 590s, and so are incompatible with these platforms. Twenty inch Mossberg 590s fit just fine, however. The hardware included with the Remington and Mossberg rails are for pump action shotguns. They can be used with semi-auto versions (Remington 1100 and Remington 11-87, or Mossberg 930) by grinding the fasteners down to the appropriate lengths. Rails for the Benelli M2 Tactical and Benelli SuperNova Tactical mount just forward of the ghost ring sights, extending to the front of the receiver. Benelli M2 Tactical rails can also be installed on round-top Benelli M1 receivers after drilling and tapping the top of the shotgun receiver with #8-40 threads. Consult a gunsmith. The Picatinny optics rail for the Kel-Tec KSG features small aluminum flanges on either side of the main rail that can accept additional lengths of Picatinny rail to support weapon lights or targeting lasers (accessory rail not included, see immediately below). A pair of unique steel recoil blocks featuring angled set screws ensure the rail assembly is securely mounted to the shotgun. #92390 Aluminum Picatinny Rail for Benelli M2 Tactical #94500 Picatinny Rail for Kel-Tec KSG (12-GA, 13 in, 18 in barrel) The Picatinny optics rail for the Kel-Tec KSG features small aluminum flanges on either side of the main rail that can accept additional lengths of Picatinny rail to support weapon lights or targeting lasers (accessory rail not included, see immediately below). A pair of unique steel recoil blocks featuring angled set screws ensure the rail assembly is securely mounted to the shotgun. #93540 Picatinny Rail for Mossberg 500 with Pic Rail Clamp (12-GA, 20 inch) www.MESATACTICAL.com 27
Page 2 and 3: Mesa Tactical is a manufacturer of
Page 4 and 5: Urbino Tactical Stock System • De
Page 6 and 7: #91780 Pocket Ambi Hook Loop for Ur
Page 8 and 9: MOHAWK Mohawk FOREND forend for se
Page 10 and 11: HIGH-TUBE TELESCOPING STOCK KIT •
Page 12 and 13: TELESCOPING STOCK KITS AND ADAPTERS
Page 14 and 15: #93890 LUCY 20 GA to 12 GA Stock A
Page 16 and 17: SIDE MOUNT SURESHELL ® ALUMINUM SH
Page 18 and 19: #90110 SureShell Carrier for FN SLP
Page 20 and 21: #91630 SureShell Carrier and Rail f
Page 22 and 23: SURESHELL SHOTSHELL CARRIERS WITH R
Page 24 and 25: BARREL AND MAGAZINE CLAMPS • Prov
Page 28 and 29: #91130 Adapter Mount Standard Profi
Page 30 and 31: HOOK LOOPS #90730 Ambi Hook Loop fo
Page 32: 1135 Baker Street Costa Mesa, CA 92

catalog

Create successful ePaper yourself

Delete template?

Save as template?