Taubmans UltraProof Acrylic Enamel Satin - Wattyl

Data Sheet TA048
Taubmans UltraProof Acrylic Enamel Satin
Page 1 of 3
PRODUCT DESCRIPTION
Taubmans UltraProof Acrylic Enamel Satin is an advanced formulation acrylic with enamel like
characteristics for interior and exterior use. It combines the smooth finishing properties and
serviceability of enamels with low odour, quick dry and convenience of water based finishes.
INTENDED USES – INTERIOR/EXTERIOR
• Doors
• Windows, trim
• Timber joinery of all types
• Broadwalls in wet areas e.g. bathroom, kitchens and laundries
TECHNICAL DATA
• Vehicle Type
• Pigmentation
• Solvent
• Pot Life
Acrylic Enamel
Titanium Dioxide
Water
Not Applicable
• Finish Satin (gloss at 60° 8 - 12%)
• Colour
• Touch Dry Time
• Recoat Time
• Preparatory Coat
• Theoretical Coverage
A comprehensive colour range is available
30 minutes at 20°C and 65% RH
4 hours at 20°C and 65% RH. Allow up to twice as long for cooler and
more humid conditions.
Required
14 - 16 m²/L
• Dry Film Thickness 25µ
• Usual Number of Coats 2
• Toxicity of dry film
• Durability
• Thinning and Clean Up
• V.O.C.
• Pack Sizes
Non Toxic
Excellent
Do not thin. Cleanup: water, away from drains
46g/L as per EC-07-07
1L, 2L, 4L
Reason for Issue: Format update Version: 2.0 Issue Date: 09/01/08
WATTYL (NZ) LTD
INFORMATION HELP LINE: 0800 735551 (New Zealand)

Taubmans UltraProof Acrylic Enamel Satin
Data Sheet TA048
Page 2 of 3
PERFORMANCE PARAMETERS
Features
• Non yellowing.
• Ideal for broadwalls in wet areas.
• Resists sticking on contact areas.
• Rapid dry.
• Good exterior gloss retention.
Constraints
• Do not apply when the temperature is below 5°C, the humidity is greater than 85%, or if dew or
rainfall is likely within 4 hours of application (for exteriors).
• Exposure to condensation or steam should be avoided for the first 48 hours.
• Not recommended for exterior weatherboards.
SURFACE PREPARATION
Remove grease, dust and dirt by washing down with liquid sugar soap as per label directions. If
mould is present treat with proprietary mould killer as per label directions.
If wallpaper has been stripped all wallpaper paste should be removed.
All loose, peeling and flaking material must be removed. Old glossy surfaces must be sanded to a
dull finish before repainting. Fill holes and cracks with a suitable filler. Sand the surface smooth
with 150 or 180 grit sandpaper. Apply the appropriate sealer system and allow to dry before
sanding lightly and over coating with two coats of Taubmans UltraProof Acrylic Enamel.
Interior
Bare Timber & MDF: Taubmans UnderProof Acrylic Primer Undercoat
Bare GIB ® : Taubmans UnderProof Undercoat and Wallboard Sealer.
Sun burnt or skim coated GIB ® : Taubmans UnderProof Pigmented Sealer.
Previously Painted Surfaces: Taubmans UnderProof Undercoat and Wallboard Sealer or
Taubmans UnderProof Primer Sealer Undercoat.
Exterior
New Timber: Taubmans UnderProof Wood Primer
Cement, Fibre Cement: Taubmans UnderProof Acrylic Primer Undercoat
Previously Painted Surfaces: Taubmans UnderProof Acrylic Primer Undercoat as required
APPLICATION
Stir paint thoroughly with a flat stirrer until contents are uniform and thoroughly mixed.
Do not thin as product is ready for use. Use a dry brush and roller where possible.
Apply with a good quality brush, 6 - 8mm nap roller or airless spray.
Provide adequate ventilation during use.
NOTES
To avoid blocking, contact surfaces should be left for a minimum of 8 hours before closing.
1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that:
(a) The user should check the date of printing, and if more than 24 months have elapsed, should verify with our nearest sales office that the information is still current. (b) you review the Technical Data Sheets (TDS) and
Material Safety Data Sheets (MSDS) before you use or handle the product; (c) the product be used only in accordance with the information provided by Wattyl; (d) the product be transported, stored and handled in
accordance with the information on the MSDS and relevant TDS; and (e) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product.
2. The information in this technical data sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its
contents, Wattyl cannot guarantee that the information provided is wholly comprehensive.
3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling
the product. If you require further information please contact your nearest Wattyl Office.
4. Because we cannot control the way these products may be used, or the conditions they may be exposed to, we can give no express guarantees in respect of these products or their performance. However certain
guarantees may be implied by law.
Wattyl (N.Z.) Limited, P. O. Box 1545, Auckland, 1. Phone 09 820 6700 Fax 09 820 6572
WATTYL (NZ) LTD
INFORMATION HELP LINE: 0800 735551 (New Zealand)

Taubmans UltraProof Acrylic Enamel Satin
Data Sheet TA048
Page 3 of 3
MATERIAL SAFETY DATA SHEETS
Wattyl (N.Z) Ltd Material Safety Data Sheets contain pertinent information that you may need to
protect your employees and customers against any known health or safety hazards associated
with our products, and are available on request.
1. This information is provided with respect to the listed Wattyl products. Wattyl recommends that:
(a) The user should check the date of printing, and if more than 24 months have elapsed, should verify with our nearest sales office that the information is still current. (b) you review the Technical Data Sheets (TDS) and
Material Safety Data Sheets (MSDS) before you use or handle the product; (c) the product be used only in accordance with the information provided by Wattyl; (d) the product be transported, stored and handled in
accordance with the information on the MSDS and relevant TDS; and (e) you thoroughly test the product, using the recommended application method on a sample of intended substrate, before using the product.
2. The information in this technical data sheet was prepared using information gathered during product development. While Wattyl endeavours to update this information and maintain the accuracy and currency of its
contents, Wattyl cannot guarantee that the information provided is wholly comprehensive.
3. Wattyl recommends that you conduct such additional investigations as may be necessary to satisfy yourself of the accuracy, currency and comprehensiveness of the information on which you rely in using and handling
the product. If you require further information please contact your nearest Wattyl Office.
4. Because we cannot control the way these products may be used, or the conditions they may be exposed to, we can give no express guarantees in respect of these products or their performance. However certain
guarantees may be implied by law.
Wattyl (N.Z.) Limited, P. O. Box 1545, Auckland, 1. Phone 09 820 6700 Fax 09 820 6572
WATTYL (NZ) LTD
INFORMATION HELP LINE: 0800 735551 (New Zealand)