Transmode TP10G_F_A4.cdr - CB Networks

CB Networks - Tel: 33 (0)1 72 74 16 25 - E-Mail: sales@cbnetworks.fr
Data Sheet
10Gb/s Networking
TM-Series
TM-3000/-301/-101/-102
XFP
Client
TP10GCLX
DWDM
i/f
The TP10BCLX
can be mounted
stand-alone in
the TM-101/-102
chassis or in the
larger TM-301
or TM-3000 chassis
where it can be
combined with
other CWDM
or DWDM Traffic
Units.
See separate
Data Sheets for
more information
about these
products
10G Transponder
The TP10G Transponder (TP10GCLX/zzzzz) is a powerful unit for 10GbE-WAN/STM-64/OC-192 and 10GbE LAN traffic
formats with the following functions and features:
- Client signal is mapped into a G.709 digital wrapper.
TM-101/-102
TM-301
- Embedded management channel enables easy access to remote NE’s without need for local DCN access or
separate OSC channel.
- Boosted transmission distance via line coding (FEC) that detects and corrects bit errors (Forward Error
Correction).
- XFP Transceiver on client interface to enable different interfacing alternatives towards client equipment.
TM-3000
- Discrete line interface to provide highest transmission characteristics for long-haul applications
- PM extraction on both client and line interface every 15min/24h that is presented according to G.826 in the
node and network manager.
- Near-end client and far-end line loop-back for fault-finding and to ease installation and commissioning.
Double Dual GbE
Transponder
- Supports equipment protection where two TP10G units are combined via a passive optical coupler/splitter (OCU).
The 10G Transponder can be mounted in the TM-101/-102, TM-301 or TM-3000 chassis’ for either fiber-pair or singlefiber
configurations.
Quad MultiRate
Transponder
Long-haul applications
1
TP10GCLX
Optical DWDM
Mux/DeMuxes
1
8
8ch DWDM MDU-E
Pre-Amplifier
Fiber pair
Pre-Amplifier
ptp-link on a fiber-pair configuration
Optical DWDM
Mux/DeMuxes
1
The TP10G Transponder is primarily intended for amplified point-to-point and bus networks where the FEC coding gives
the needed boost in transmission performance. Up to 80 DWDM channels are currently supported for distances up to
600km using intermediate line amplifiers, dispersion compensation etc.
8ch DWDM MDU-E
8
TP10GCLX
1
8-port SDH/SONET
MuxPonder
4xSTM-16/STM-64
MuxPonder

CB Networks - Tel: 33 (0)1 72 74 16 25 - E-Mail: sales@cbnetworks.fr
Protection
OCU
TP10GCLX
TP10GCLX
Two TP10G units can be connected to provide equipment protection.
A passive optical coupler/combiner is placed between the Transponders and the
client equipment as shown in the figure.
One Transponder is set to “active” and the other in “stand-by” mode. Only the
active Transponder has its client laser turned on. Upon a failure on the active
path, the active Transponder will turn off its client laser and a HW-connected
signal will activate the stand-by Transponder. This switch is done within 20ms.
The TM-series
Platform entails
both CWDM and
Mentis DWDM Platform solutions
in single-fibre
or fibre-pair
configurations.
All in the same
card cage, one the
same fibre and
under the same
node and network
management
system.
Equipm protection
Technical Data
Parameter Value Comment
Power consumption
Timing
Performance monitoring
Embedded management channels
Misc
25W
Through-timing in both directions
Fully equipped
Full 3R
- PM on client and line interfaces collected every 15min/24h and presented according to G.826.
- Optical parameters: Laser output power, Laser bias, Received optical power
Yes
G.709 wrapper on line interface with Forward Error Correction (FEC)
Near-end loop-back on client interface. Far-end loopback on line interface
6-port Ethernet
Demarcation Unit
9xGbE/10G
Muxponder
Optical Interfaces
Module type
Client XFP
80km discrete DWDM
10G Tunable Transponder
Signal types
10Gbe LAN (10.3125Gb/s)
10GbE WAN (9.95328Gb/s)
STM-64/OC-192 (9.95328Gb/s)
G.709 wrapper with FEC
STM-64/OC-192 and 10GbE WAN = 10.709Gb/s
10GbE LAN = 11.0957Gb/S
Connector type
LC
MU
Input fiber type
Interface type
SM
STM-64 I-64.1 (~2km)
OC-192 SR-1 (~2km)
10GBASE-LR/LW (~10km)
SM
Long reach ~80km
Double 10GbE
DWDM Transponder
Output
wavelength (nm)
Output power
1260 - 1360
-6dBm min
-1dBm max
Single-fiber config: 192.10, 192.30, 192.50 ..... 195.90 THz
(20 wavelengths in C-band @ 200GHz spacing)
Fiber-apir config: 192.10, 192.20, 192.30 ....... 195.10 THz
(32 wavelengths in C-band @ 100GHz spacing
-2dBm min
+3dBm max
ROADM
Receiver sensitivity @ 10 -12
-14dBm
-26dBm
Overload
Link budget
excl. Network Margin and
excl. Dispersion Penalty
Network Margin (recomm)
0dBm
8dB
2dB
-5dBm
8 - 22dB
2dB
Embedded
Node Manager (ENM)
Dispersion Penalty
-
1dB at 800 -1200 ps/nm
2dB at 1200 - 1400ps/nm
The specifications and information within this document are subject to change without further notice. All statements, information and recommendations are
believed to be accurate but are presented without warranty of any kind. NOTE! The above transceivers are a subset of all available transceiver types. Contact Transmode for more details.
Transmode
Network Manager (TNM)
DS-TP10G
Rev F Mar 2008
12 avenue des prés
78059 St Quentin en Yvelines
Transmode Systems AB
web: www.transmode.com
BOX 42114 Tel: 33 (0)1 72 74 email: 16 25 info@transmode.com
SE-126 14 Stockholm Fax: 33 (0)1 30 telephone: 44 11 95 +46 (0)8 527 675 50
http://www.cbnetworks.fr Sweden E-mail: sales@cbnetworks.fr