28.01.2015 Views

4646-X413 - Vacuumschmelze

4646-X413 - Vacuumschmelze

4646-X413 - Vacuumschmelze

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

Additional Information Item No.: T60404-N<strong>4646</strong>-<strong>X413</strong><br />

VACUUMSCHMELZE<br />

K-No.: 24831<br />

100 A Current Sensor<br />

For electronic current measurement:<br />

DC, AC, pulsed, mixed ..., with a galvanic<br />

isolation between primary circuit<br />

(high power) and secondary circuit<br />

Date: 28.01.2008<br />

Customer: Customers Part No.: Page 3 of 3<br />

ME<br />

A=km<br />

1=St<br />

2=kg<br />

3=g<br />

4=l<br />

5=m<br />

6=m²<br />

7=m³<br />

8=mm<br />

9:Paar<br />

I 0H:<br />

I 0t:<br />

t r:<br />

∆t (I Pmax):<br />

X ges(I PN):<br />

Zero variation of I o after overloading with a DC of tenfold the rated value (R M = R MN)<br />

Long term drift of I o after 100 temperature cycles in the range -40 bis 85 °C.<br />

Response time (describe the dynamic performance for the specified measurement range), measured as delay time<br />

at I P = 0,9 . I Pmax between a rectangular current and the output current.<br />

Delay time (describe the dynamic performance for the rapid current pulse rate e.g short circuit current)<br />

measured between I Pmax and the output current i a with a primary current rise of di 1/dt = 100 A/µs.<br />

The sum of all possible errors over the temperature range by measuring a current I PN:<br />

IS<br />

( IPN<br />

)<br />

X<br />

ges = 100 ⋅ − 1 %<br />

K ⋅ I<br />

N<br />

PN<br />

X: Permissible measurement error in the final inspection at RT, defined by<br />

X<br />

I<br />

= 100 ⋅<br />

SB − 1 %<br />

I<br />

SN<br />

where I SB is the output DC value of an input DC current of the same magnitude as the (positive) rated current (I o = 0 )<br />

X Ti:<br />

ε L:<br />

Temperature drift of the rated value orientated output term. I SN (cf. Notes on F i) in a specified temperature range,<br />

obtained by:<br />

I<br />

( T ) − I ( T )<br />

SB A2 SB A1<br />

X<br />

Ti<br />

= 100 ⋅<br />

%<br />

I<br />

SN<br />

Linearity fault defined by<br />

I<br />

P Sx<br />

ε L=<br />

100 ⋅ − %<br />

IPN<br />

ISN<br />

Where I P is any input DC and I Sx the corresponding output term. I SN: see notes of F i (I o = 0).<br />

I<br />

This “Additional information“ is no declaration of warranty according BGB $443.<br />

Hrsg.: KB-E<br />

Bearb: SA<br />

editor<br />

designer check<br />

Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts<br />

nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu<br />

Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten<br />

KB-E BE: Len<br />

KB-PM IA: KRe.<br />

freig.: Heu.<br />

released<br />

check<br />

Copying of this document, disclosing it to third parties or using the contents there for any<br />

purposes without express written authorization by use illegally forbidden.<br />

Any offenders are liable to pay all relevant damages.

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!