Max stroke 750 mm - Market

SL60
Linear stem actuator – Thrust force 600N – Max stroke 750 mm

67
63.8
42
27.7
347.5
12
375.2
14.5
ø5
515.7
12
488
15.7
52.5
37.5
38
32
47
32
57
141.4
39
104
22
130.5
ø5
50
38
47.5
55.9
6.5
Technical Characteristics
SL60H
SL60L
Power supply voltage 230V-50Hz 24V DC
Max recommended load in thrust/traction position
600N
Available strokes
180- 230-350-550-750 mm
Rated absorbed current 0,330A 1,500A
Idle translation speed 18mm/sec 10 mm/sec
Duration of the idle stroke
(stroke: loadless translation speed)
Double electric insulation
YES
Service type
S2 of 3 min
Operating temperature
-5+50°C
Protection degree of electric devices
IP55
Connection of two or more actuators in parallel
YES
Stroke end system
Micro-switch

Description for technical specifications
Linear electric actuator TOPP model SL60 with self-aligning tilting movement, complete
with support and fitting accessory for top hung window. Operation at 230V~ 50Hz, or at
24V d.c. Max. traction and thrust force of 600N. Pre-set for the connection in parallel
of two or more actuators, with end of stroke microswitches.
Available strokes: 180 – 230 – 350 - 550 – 750 mm. CE marked device complying with
the following directives: EEC 89/336, EEC 73/23 and following amendments.
SL60

USA2_USA3
Connection and synchronization unit for 2 or 3 ACK4, C30 or C40

Description for technical specifications
The USA is a device that synchronizes, controls and monitors the simultaneous running of ACK4 actuators fitted on the same frame. It
becomes essential when two or three ACK4 chain actuators are set up on large size windows, providing a regular and even movement of
the vents, to guarantee the security of the frame and connected motors.
The microprocessor of this unit checks in real time the actuators feeding power, consumption and speed. When any one of the checked
parameters does not meet the standard, the USA automatically disconnects the feeding and signals, by a pilot light, which actuator is causing
the failure.Only two or three actuators, preset with a five-wire cable connection, can be linked to the USA2 and USA3. The unit is fitted in
a grey shock-resistant plastic case. Both the unit and the actuators can work either at 230V – 50Hz or 24V DC. It is preset for connection
to all wind, rain, air-conditioning, smoke and heat evacuation systems.
CE marked device complying with the following regulations: EEC 89/336, EEC 73/23 and following amendments.
Technical characteristics
USA2 USA3 USA2 USA3
Power supply voltage 230 V ~ 50 Hz 24 V DC
Autput voltage 230 V ~ 50 Hz 24 V DC
Total max. absorption applied (ACK4) 0,64 A 0,96 A 4,2 A 6,3 A
Total max. absorption applied (C30) 0,64 A 0,96 A 2,6 A 3,9 A
Total max. absorption applied (C40) 0,48 A 0,72 A 2,2 A 3,3 A
Operating temperature - 5 + 50 ºC
Minimum distance between the actuators of the same frame
1,5 m
Length of the cables for power supply
Overall dimensions
2,2 m
200x155x80 mm
Total thrust force (ACK4) 600N 800N 600N 800N
Total thrust force (C30) 600N 800N 600N 800N
Total thrust force (C40) 700N 900N 700N 900N
Total traction force (ACK4) 400N 600N 600N 800N
Total traction force (C30) 400N 600N 600N 800N
Total traction force (C40) 700N 900N 700N 900N

AL24/2_24/5_24/10
Power unit for actuators at 24V

Description for technical specifications
The AL24 feeder supplies low voltage 24V actuators or, if connected to the EVP, it realizes a feeding group for the low voltage 24V actuators.
A relay grants high reliability and safety of the motors. The actuator’s movement is manually controlled through a double push-button or by
a switch. The AL24/2 (4A) and the AL24/5 (10A) may be simultaneously activated by a single control.
The AL24/10 (20A) allows to divide the control in two separate zones according to the installation requirements. The feeding unit is
contained in shockproof plastic. CE marked device complying with the following regulations: EEC 89/336, EEC 73/23 and following
amendments.
Technical characteristics
AL24/2 AL24/5 AL24/10
Power supply voltage
230V 50Hz
Output voltage
24V DC
Max exit current 4 A 10 A 20 A
Service type
S1-continuous
Operating temperature - 5 + 50°C
Weight 2,500 Kg 4,550 Kg 6,750 Kg
Dimensions (mm) 200x250x95 200x250x130 200x250x130
ACK4 that can be connected 2 pcs 5 pcs 10 pcs
C30 that can be connected 3 pcs 7 pcs 14 pcs
C40 that can be connected 3 pcs 9 pcs 18 pcs
SL60 that can be connected 3 pcs 6 pcs 12 pcs
ALTF Feeder with batteries buffer-charged
The system is composed by a stabilized feeder and a couple of batteries, 12 V, connected in series and buffer charged. The unit ensures,
in case of power failure, the power supply of the motors connected to the units for control and ventilation TF21/TF24. CE marked equipment,
complying with the following directives: EEC 89/336, EEC 73/23 and following amendments.
Technical characteristics
ALTF
Power supply voltage
230 V 50Hz.
Output voltage
24/12 V d.c.
Max output current 24V
16 A
Max output current 12V 0.2A
Operating temperature - 5 + 50 ºC
Connectable control units
Series TF
Overall dimensions
L.230Xh.310X130 mm.

TF21/24_TF41/44
Control and power units for actuators at 24V and 230V

Description for technical specifications
The new TF21/24 (24V output voltage) and TF41/44 (230V output voltage) control units are designed to feed and control, the connected
motors. The actuators may be individually or simultaneously operated when connected to a manual or radio control. With the suitable model
we can supply the F33 radio control at 433 Mhz or the F27 infrared remote control. If necessary, the receiver of the infrared remote control
can be installed outside the unit (for example,near the manual controls) up to a max. distance of 5 meters.
The radio and remote controls work with sequential step system (opening – stop – closing – stop….).
Every push button controls the respective motor. The simultaneous pushing of two buttons opens or closes all the connected motors.
The RPR rain sensor (12V), the RW wind sensor and the RL light sensor may be connected to these units. The TF21/24 and TF41/44
units are fitted in shock-resistant plastic. CE marked device complying with the following regulations: EEC 89/336, EEC 73/23 and following
amendments.
Technical characteristics
TF21 TF24 TF41 TF44
TF21R/T TF24R/T TF41R/T TF44R/T
Power supply voltage
230V~50Hz
Output voltage 24V DC 230V
Max power consumption 15W 45W 300W 1200W
Max absorbed current 0,36A 1,5A 1,3A 5,2A
Service type S1 – Continuous
Preset for
Wind/rain/light sensors, manual control
Operating temperature - 5 + 50°C
Dimensions (mm)
160x120x75
C20 that can be connected 1pc 4 pcs 2 pcs 8 pcs
ACK4 that can be connected - - 4 pcs 16 pcs
C30 that can be connected - 1pc 4 pcs 16 pcs
C40 that can be connected - 1 pc 5 pcs 20 pcs
SL60 that can be connected - 1pc 4 pcs 16 pcs

EVP
Wind/Rain Control Unit

Description for technical specifications
The EVP wind/rain control unit automatically and independently controls and closes the frames in case of
emergency through wind and rain sensors, that is when the preset values have been exceeded. The rain sensor connected to the EVP is
the low voltage RPR heated version (12V). The unit allows the connection of 230V actuators. If a higher number of actuators are
necessary than the standard, the system can be implemented with more motors, by presetting the equipment with
a proper powerful relay or by using one or more M5 modules. Every module is controlled by the same wind and rain sensor.
An AL24 feeder, preset to receive the motor’s opening and closing pulse from the EVP, is required for the power going to the low voltage
24V actuators. CE marked device complying with the following regulations: EEC 89/336, EEC 73/23 and following amendments.
Technical characteristics
EVP
Power supply voltage
230V-50Hz
Max output power
500 W
Max absorbed current
2,2 A
Service type
S1-continuous
Preset for
Wind/rain sensors, manual control and/or thermostat*
Operating temperature - 5 + 50°C
Dimensions (mm)
113x107x45
C20 that can be connected
2 pcs
ACK4 that can be connected
6 pcs
C30 that can be connected
6 pcs
C40 that can be connected
9 pcs
SL60 that can be connected
6 pcs
(* not compatible with the C20 actuator)

M5
Module to Control/Feed 230V Motors

Description for technical specifications
The M5 wind/rain unit automatically and independently controls the emergencies through wind and rain sensors, closing and opening the
windows according to the processed impulses.
The module is set for:
• Five outputs for the actuators
• Single control of every exit
• The simultaneous control of all exits
The rain sensor connected to the M5 is the low voltage RPR heated version (12V).
The M5 is contained in
shockproof plastic. CE marked device complying with the following regulations: EEC 89/336, EEC 73/23 and following amendments.
Technical characteristics
M5
Power supply voltage
230V-50Hz
Max output power per exit
370 W
Max output current per exit
1,6 A
Feeding exits 5
Service type
S1-continuous
Preset for
Wind/rain sensors, manual control or thermostat*
Operating temperature -5 + 50°C
Dimensions
160x120x75 (mm)
C20 that can be connected
2 pcs
C30 that can be connected
5 pcs
C40 that can be connected
6 pcs
ACK4 that can be connected
5 pcs
SL60 that can be connected
5 pcs
(* not compatible with the C20 actuator)

AC8
MEM/AL
PCU32
AC8_PCU32_MEM/AL
Modular surveying units of control and detection

Description for technical specifications
The AC8 and the PCU32 represent a modular control and surveying system for the evacuation of smoke and heat and to control climatic
variations such as rain and wind. The module system has been designed to allow the customer great flexibility to implement and to program
the system according to specific requirements.
The AC8 control unit can be connected up to a max of 31 units by means of a RS485 serial line. The AC8 can be employed in three
different application systems:
• SINGLE: only one AC8 unit to control one single area (connection of 24V voltage motors for max. 16A)
• MULTIPLE: more than one units, to control various areas simultaneously (max 31)
• COMBINED MULTIPLE: to control more areas from one single point (many AC8 units and 1 PCU32 display).
The PCU32 module, equipped witn a LCD display, displays and monitors the status of all the AC8 control units connected to it and control
them in single or multiple way. It has the buttons for the general command and the matrix to display the status of the peripheral modules
of each zone.
This innovative system allows to place the AC8 module close to the motors to control. Each system’s configuration can be further implemented
with the MEM/AL optional module that allows the connection of 24V motors for max. 16A. It just feeds the motors while the AC8 operates
them. A wide choice of accessories, such as electric sirens, flashing lights and automatic dials can be connected to the AC8 and the PCU32
units. The alarm caused by smoke, gas and temperature sensors is prior to every other function. Each MEM/AL module is supported by
a feeder and batteries; the connection between control unit and MEM/AL module does not need particular wires
but a standard cable with minimum diameter. The AC8 control unit can work also with 230V motors: if controlled by the M5 module they
can be used for ventilation. All detectors (wind/rain/smoke/gas, etc. sensors) can be connected to the M5, that independently processes
the emergency and operates the window. A battery pack at 24V and buffer charged ensures the power supply to the connected safety
sensors for 72 hours avoiding any power loss and useless long wiring costs. The feeding unit is contained in shockproof grey plastic, with
IP55 protection rating. CE marked device complying with the following regulations: EEC 89/336, EEC 73/23 and following amendmens.
Technical characteristics
AC8
MEM/AL
Power supply voltage
230V-50Hz
Output voltage
24V DC
Max absorbed current 0,22A 0,3A
Service type
S1-Continuous
Preset for
Wind/rain/smoke sensors, manual switch
Operating temperature 5 + 50°C
Dimensions (mm) 320x360x140 225x315x190
C20 that can be connected 32 pcs 32 pcs
C30 that can be connected 12 pcs 12 pcs
C40 that can be connected 14 pcs 14pcs
ACK4 that can be connected 8 pcs 8 pcs
SL60 that can be connected 10 pcs 10 pcs

RW - RPR/RPR2
RF811
RF813
PM1_PM2_PM3
EA
RF811_RF813_PM_EA
RW_RPR/RPR2

RW Wind Sensor_RPR/RPR2 Rain Sensor
The wind sensor, connected to TF21, TF24, EVP, M5 and AC8, is a device that controls the automatic closure of windows when the wind
speed exceeds the preset defined value. The RW is contained in weatherproof plastic, with rotating blade system to catch the wind speed.
As the wind sensor, the rain sensor must be located outside, exposed to rain.
The RPR low tension version (12V) may be connected to the TF21, TF24, EVP and M5 control units; the RPR2 version (230V) may be
connected to the AC8 and TF40. They automatically close windows when the comb sensor is wet; as they are heated, they dry off quickly
and are insensitive to fog, ice, dew and damp.
RF811 Smoke Detector
The RF811 is an optic smoke sensor for indoor smoke detection. It can be connected to the AC8 unit in systems for smoke evacuation.
UNI EN54 regulated, it secures high reliability and is protected against false alarms.
RF813 Temperature Detector
The RF813 analogical temperature detector reacts immediately to rapid increases in temperature.
It can be connected to the AC8 control unit in systems for smoke evacuation and is UNI EN54 regulated.
PM1_PM2_PM3 Keyboards
PM keyboards control one or more actuators. Designed to be fitted against the wall, they have 1 or 2 buttons according to the required
model. The box is in shockproof plastic and is equipped with a 10A double switch button with 6 clamps, and a Ø5x20
fuse block.
EA Emergency Control
The EA is a manual control device that creates an alarm state when the glass is broken and activates the window
opening. The push button consists of 2 contacts: one is N.A: (normally OPEN) and the other one is N.C. (normally CLOSED).
The red external colour of the box responds to the standard safety rules and is IP55 rated.