SAMBA75 & WINDOWS VISTA Driver installation - Falcom

This document is available at HTTP://WWW.FALCOM.DE/
SAMBA75
&
Version: 1.0.0; Created: 22/06/2007
WINDOWS VISTA
Driver installation

SAMBA75 & WINDOWS VISTA DRIVER INSTALLATION VERSION 1.0.0
Table of contentS
1 INTRODUCTION ........................................................................ 3
1.1 INSTALLING SAMBA75 DRIVER ON THE WINDOWS VISTA ................................................... 3
Version history:
Version number Author Changes Release Date
1.0.0 Fadil Beqiri - Initial version 22/06/2007
This confidential document is a property of FALCOM and may not be copied or circulated without previous permission.
Page 2

SAMBA75 & WINDOWS VISTA DRIVER INSTALLATION VERSION 1.0.0
1 INTRODUCTION
This document describes how to install the SAMBA75 driver on Microsoft Windows®
Vista (32-bit only). Configurations and settings for other operating systems
(Windows 2000 and XP) are available in the manual “Getting started”.
Note: All screen shots presented in this guide were taken in the German language.
1.1 Installing SAMBA75 driver on the Windows® Vista
To get and install SAMBA75 driver, please follow the steps below:
1. Download the required driver package from the FALCOM homepage.
2. Please make sure you use a SIM-card with deactivated PIN before starting
with the next steps.
3. After plugging in the SAMBA75, Vista will ask you what to do with the new
hardware. Please, choose „Ask me again later“
Figure 1: A bubble from the taskbar indicates that the device driver software is being
installed.
Figure 2: Start the installation by clicking „Ask me again later“
This confidential document is a property of FALCOM and may not be copied or circulated without previous permission.
Page 3

SAMBA75 & WINDOWS VISTA DRIVER INSTALLATION VERSION 1.0.0
4. Open the system tray and right-click the MC75 device. Choose „Update
driver“.
Figure 3: Update the MC75 driver form the Device manager.
5. A window displays with two options, select “Browse the computer for the
drivers”.
Figure 4: Select “Browse the computer for the driver”
This confidential document is a property of FALCOM and may not be copied or circulated without previous permission.
Page 4

SAMBA75 & WINDOWS VISTA DRIVER INSTALLATION VERSION 1.0.0
6. Click Browse button and select the driver, then click Next. The driver will
now be installed from its location.
Figure 5: Browse to the MC75 driver folder.
7. A window displays the message “The software for this device has been
successfully installed”. Click Close.
Figure 6: The MC75 driver has been successfully installed .
This confidential document is a property of FALCOM and may not be copied or circulated without previous permission.
Page 5

SAMBA75 & WINDOWS VISTA DRIVER INSTALLATION VERSION 1.0.0
8. To setup GPRS please right-click the SIEMENS AG WM USB Modem and go
to advanced settings. Add AT+CGDCONT=1,“IP“,”APN” (where APN is
supplied to you by your mobile operator).
Figure 7: GPRS extra initialization command.
9. Click Set up a connection or network.
Figure 8: Set up a connection.
This confidential document is a property of FALCOM and may not be copied or circulated without previous permission.
Page 6

SAMBA75 & WINDOWS VISTA DRIVER INSTALLATION VERSION 1.0.0
10. Then click Set up a dial-up connection using the Siemens AG WM USB
Modem.
Figure 9: Set up a dial-up connection.
11. Enter the dial-up phone number *99***1#. The login name and password
are supplied to you by your mobile provider.
Figure 10: Enter the information from your Internet Service Provider (ISP).
This confidential document is a property of FALCOM and may not be copied or circulated without previous permission.
Page 7

SAMBA75 & WINDOWS VISTA DRIVER INSTALLATION VERSION 1.0.0
Figure 11: Online state.
This window indicates that you have successfully connected to the Internet. Click
on Close.
This confidential document is a property of FALCOM and may not be copied or circulated without previous permission.
Page 8