177-467 rev. 5 - Diebold

More documents

Recommendations

Info

DIMENSIONS IN MILLIMETRES (DIMENSIONS IN INCHES) THIRD ANGLE PROJECTION PAGE 2 OF 4 SUBJECT TO CHANGE WITHOUT NOTICE" "ALL DIMENSIONS AND DESIGN CRITERIA FILE NO. 177-467 REV. 5 1 2 3 4 5 CONDUIT AND JUNCTION BOX REQUIREMENTS NOTE: SIGNAL CABLE RUN CONSTRAINTS THE FOLLOWING CHART ITEMIZES THE PHYSICAL SPACING REQUIREMENTS OF THE SIGNAL CABLE RUN WITH RESPECT TO OTHER POWER AND ELECTRICAL EQUIPMENT CABLE RUN. TYPE OF ELECTRICAL RUN FLUORESCENT, NEON OR INCANDESCENT LIGHTING FIXTURES UNSHIELDED POWER LINE OR ELECTRICAL EQUIPMENT CONDUIT 19 ") 4 3 ( 1613 1 (63 2") 1594 25mm (1") METAL CONDUIT FROM ALARM CONTROL CABINET 1 JUNCTION BOX TO 102mm (4") SQ. X 54mm (2 8") DEEP JUNCTI0N BOX (ALL BY OWNER’S E.C.). DIEBOLD TO PROVIDE FLAT COVER WITH TAMPER SWITCH. WHEN "SECUROMATIC" AFTER HOUR DEPOSITORY IS TO BE CONNECTED TO 3 THE ATM, OWNER’S E.C. TO RUN 19mm ( 4") METAL CONDUIT FROM 1 102mm (4") SQ. X 54mm (2 8") DP. JUNCTION BOX TO AFTER HOUR DEPOSITORY. 3 OWNER’S E.C. TO RUN 19mm ( 4") LIQUID TIGHT FLEX METAL 3 CONDUIT OR 19mm ( 4") RIGID CONDUIT FROM JUNCTION BOX TO CABLE CONNECTION PLATE. 3 19mm ( 4") METAL CONDUIT AND UNSWITCHED ELECTRICAL SUPPLY 1 TO 102mm (4") SQ. X 54mm (2 8") DEEP JUNCTION BOX WITH RECEPTACLE WITHIN 2210mm (87") OF SIDE CONNECTING PLATE. BOTTOM CONNECTION MUST BE COMPENSATED ACCORDINGLY (ALL BY OWNER’S E.C.) (SEE POWER REQUIREMENTS). OWNER’S E.C. TO SUPPLY COMPATIBLE RECEPTACLE FOR COUNTRY SPECIFIC PLUG-IN CONNECTOR SUPPLIED WITH UNIT. POWER CORD LENGTH 2184mm (86") FROM SIDE OF UNIT. JUNCTION BOXES MUST BE LOCATED WITHIN 2210mm (87") OF CONNECTING PLATE. (LENGTH OF ELECTRICAL POWER CABLE PROVIDED WITH UNIT). LOCATE IN AN EASILY ACCESSIBLE AREA. BOXES CAN BE FLUSH MOUNTED WITH CONCEALED CONDUIT FOR NEW CONSTRUCTION OR BOXES CAN BE SURFACE MOUNTED WITH EXPOSED CONDUIT FOR EXISTING CONSTRUCTION. UNSHIELDED POWER LINES OR ELECTRICAL EQUIPMENT WITH SIGNAL CABLES ENCLOSED IN GROUNDED CONDUIT POWER LINES IN GROUNDED CONDUIT WITH SIGNAL CABLES IN GROUNDED SIGNAL CABLE INSTALLATION CONSTRAINTS: RELATIVE CARE IS REQUIRED WHEN INSTALLING SIGNAL CABLES IN CONDUITS, UNLIKE POWER AND LIGHTING CABLE, SIGNAL CABLES HAVE CONDUCTORS AND LIGHT INSULATION AND WILL NOT WITHSTAND AS MUCH STRAIN IN INSTALLATION. 21 ") 16 13 ( 40 ") 4 3 (62 ") 16 9 (1 63 1 (2 2") 1533 ") 8 3 (60 13 1 ( 2") BELOW 2 KVA 2-5 KVA ABOVE 5 KVA 679 3 (26 4") 768 1 (30 4") 794 1 (31 4") 13 1 ( 2") BACK ELEVATION SEPARATION FROM OTHER CABLES 127mm (5") 127mm (5") 127mm (5") 127mm (5") 305mm (1’-0") 610mm (2’-0") 1 64mm (2 2") 152mm (6") 305mm (1’-0") 3 30mm (1 16") 76mm (3") 152mm (6") 51 (2") AIR VENTS 4 1 2 4 1 5 3 POWER REQUIREMENTS: THE ATM REQUIRES A SINGLE-PHASE, THREE-WIRE UNSWITCHED POWER RECEPTACLE. WIRING TO THE RECEPTACLE MUST INCLUDE A THIRD-WIRE EARTH GROUND (CONDUIT GROUND IS NOT ACCEPTABLE). THE ATM WILL PROVIDE A POWER CORD WITH A COUNTRY SPECIFIC POWER PLUG. THE POWER SUPPLIED MUST BE AS SPECIFIED BELOW. 100-127 VAC (+6%, -10%) AT 50 (–1%) Hz, SINGLE-PHASE 100-127 VAC (+6%, -10%) AT 60 (–1%) Hz, SINGLE-PHASE 200-240 VAC (–10%) AT 50 (–1%) Hz, SINGLE-PHASE 200-240 VAC (–10%) AT 50 (–1%) Hz, SINGLE-PHASE POWER TO THE ATM IS TO BE A DEDICATED SERVICE AND MUST BE PROTECTED BY A SAFETY QUICK-DISCONNECT DEVICE TO BREAK LINE VOLTAGE (SUCH AS A CIRCUIT BREAKER AT THE ELECTRICAL SERVICE PANEL. THE QUICK-DISCONNECT DEVICE (OR CIRCUIT BREAKER) MUST TURN OFF THE LINE VOLTAGE AT THE FOLLOWING AMPERAGE. 100-127 VAC (+6%, -10%) SERVICE, DISCONNECT AT 20 AMPERES 200-240 VAC (–10%) SERVICE, DISCONNECT AT 10 AMPERES THE MODULE BULK POWER SUPPLY AND PROCESSOR POWER SUPPLY WILL PROVIDE POWER CONDITIONING TO PREVENT THE TERMINAL FROM MALFUNCTIONING DUE TO SHORT-TERM AC POWER FLUCTUATIONS AS OUTLINED IN EN61000-4-11. POWER USAGE: MACHINE STATUS IDLE (NO TRANSACTION) TRANSACTION (DISPENSE OR BULK NOTE) IN PROGRESS RAPID PROCESSING TRANSACTION IN PROGRESS CONFIGURATION: 1 2 RAPID PROCESSING - SYSTEMS CONFIGURED FOR SIMULTANEOUS IDM (INTELLIGENT DEPOSITORY MODULE) AND ENA (ENHANCED NOTE ACCEPTOR) OR IDM AND BNA (BULK NOTE ACCEPTOR) OPERATIONS. 1 2 971 BTU/HR DISPENSING 648 BTU/HR IDLE 1,875 BTU/HR RAPID PROCESSING 781 BTU/HR IDLE 2,094 BTU/HR RAPID PROCESSING OPERATING ENVIRONMENT: SAFE LOCATION 104 79 ") 8 1 (4 ") 8 1 (3 AIR VENTS POWER CORD 1 2 190 WATTS 285 WATTS 550 WATTS 614 WATTS 10” C TO 38” C (50” F TO 100” F) RELATIVE HUMIDITY (NON-CONDENSING) 20 TO 80% AT 32” C (90” F), 20 TO 55% AT 38” C (100” F) 238 3 (9 8") 378 7 (14 8") 38 1 (1 2") 229 WATTS 349 WATTS PROCESSOR, COLOR LCD CONSUMER DISPLAY, MOTORIZED CARD READER, JOURNAL PRINTER, 80mm THERMAL RECEIPT PRINTER, STANDARD DEPOSITORY AND 5 HIGH AFD. PROCESSOR, SVD LCD CONSUMER DISPLAY, MOTORIZED CARD READER, JOURNAL PRINTER, 80mm THERMAL RECEIPT PRINTER, IDM, 5 HIGH AFD, AND BULK NOTE ACCEPTOR. THE POWER USE DEPENDS ON THE NUMBER AND TYPE OF DEVICES PRESENT IN THE ATM, AND THE TYPE OF TRANSACTION THE ATM IS PERFORMING. HEAT OUTPUT CONFIGURATION: 1,190 BTU/HR BULK NOTE ACCEPTING WEIGHT OF UNIT: 1,000 kg (2,200 LBS.) CAUTION LABEL 340 3 (13 8") 795 5 (31 16") 379 217 1 (8 2") 15 (14 16") SIDE ELEVATION
THIRD ANGLE DIMENSIONS IN MILLIMETRES "ALL DIMENSIONS AND DESIGN CRITERIA PAGE 3 OF 4 PROJECTION (DIMENSIONS IN INCHES) SUBJECT TO CHANGE WITHOUT NOTICE" FILE NO. 177-467 REV. 5 CALL 1-800-999-3600 NOTE: R SHOWN IS THE MINIMUM/RECOMMENDED AREA REQUIRED FOR INSTALLATION AND SERVICE. THESE DIMENSIONS SHOWN MAY BE INCREASED WHEREVER POSSIBLE TO IMPROVE INSTALLATION AND SERVICE ACCESS. USE OF ANY AREA LESS THAN THE RECOMMENDED AREA MAY RESULT IN AN INCREASE IN INSTALLATION AND SERVICE TIME. CONSULT WITH DIEBOLD INSTALLATION/SERVICE BRANCH FOR SPECIAL BUILDING CONDITIONS. RECOMMENDED SERVICE AREA MINIMUM SERVICE AREA ALL ELECTRICAL AND DATA CABLES MUST ENTER UNIT IN THIS AREA fi OPTEVA 720 ADVANCED FUNCTION LOBBY ATM REAR LOAD 1946 2206 9 5 HIGH WITH 40mm ( 1 16") SAFE ") 8 5 (76 ") 8 7 (86 903 891 152 1163 891 152 ") 16 9 (35 ") 16 1 (35 (6") ") 16 13 (45 ") 16 1 (35 (6") 321 152 418 321 152 418 ") 8 5 (12 (6") ") 16 7 (16 ") 8 5 (12 (6") ") 16 7 (16 543 3 (21 8") 51 (2") 1413 5 (55 8") PLAN VIEW (SINGLE UNIT) (MINIMUM SERVICE AREA) 543 3 (21 8") 51 (2") 1413 5 (55 8") PLAN VIEW 794 1 (31 4") 794 1 (31 4") (SINGLE UNIT) (MINIMUM SERVICE AREA) 76 (3") 76 (3")
Page 1: L556467 DIMENSIONS IN MILLIMETRES (

177-467 rev. 5 - Diebold

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?