Technical data - Industrial Water Equipment Ltd
Technical data - Industrial Water Equipment Ltd
Technical data - Industrial Water Equipment Ltd
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Technical</strong> <strong>data</strong><br />
AP100<br />
AP100<br />
The pumps are used for pumping sewage, wastewater,<br />
considerable quantities of surface water and ground<br />
water in places such as<br />
• municipal pump pits,<br />
• public buildings,<br />
• block of flats,<br />
• factories,<br />
• garages,<br />
• underground car-parks,<br />
• car wash areas,<br />
• restaurants and<br />
• hotels.<br />
Pump and stator housing<br />
The pump housing and the stator housing are made of<br />
cast iron.<br />
The stator housing is dry, i.e. not oil-filled.<br />
Discharge<br />
All AP100 pumps have a horizontal discharge port.<br />
AP100.100 have a DN 100 DIN flange.<br />
AP100.150 have a DN 150 DIN flange.<br />
Shaft and bearings<br />
The shaft is made of stainless steel and rotates in maintenance-free<br />
prelubricated ball bearings.<br />
The lower bearing is a double-row ball bearings.<br />
Impeller<br />
The impeller is a closed single-channel or two-channel<br />
cast iron impeller with a clearance of 100 mm. Cast iron<br />
is chosen as it is resistant towards mechanically wearing<br />
particles.<br />
TM00 5488 0895<br />
Shaft seal<br />
Two mechanical bellows seals with silicon carbide/<br />
silicon carbide seal faces.<br />
An oil chamber between the primary and the secondary<br />
shaft seal is filled with oil.<br />
Pump type<br />
AP100.100.24 - 61<br />
AP100.100.80 - 135<br />
AP100.150.80 - 170<br />
Motor cable<br />
Standard pumps 10 m:<br />
Ex-pumps 10 m:<br />
Materials<br />
Cooling jacket<br />
H07RNF.<br />
H07RNF - PLUS.<br />
Oil volume<br />
1.7 litres<br />
3 litres<br />
3 litres<br />
Description<br />
Materials<br />
DIN<br />
W.-Nr.<br />
AISI/ASTM<br />
Stator housing Cast iron EN-GJL-250 0.6025 ASTM 35B<br />
Pump housing Cast iron EN-GJL-250 0.6025 ASTM 35B<br />
Neck ring<br />
Bronze<br />
Impeller Cast iron EN-GJL-250 0.6025 ASTM 35B<br />
Shaft Stainless steel 1.4104 AISI 430F<br />
Bearings<br />
Heavy-duty prelubricated ball bearings<br />
Screws Stainless steel 1.4301 AISI 304<br />
Cooling jacket Stainless steel 1.4301 AISI 304<br />
Oil<br />
Shell Ondina 15, non-toxic<br />
On request all AP100 pumps can be supplied fitted with<br />
a stainless steel cooling jacket.<br />
Liquid temperature with cooling jacket: 0°C to +40°C.<br />
For short periods, max. one hour: Up to +60°C. For<br />
periods longer than one hour, external cooling is<br />
required.<br />
The cooling jacket is available for internal as well as<br />
external cooling of the motor in both dry and submerged<br />
installations.<br />
Internal cooling (standard) is achieved by leading part of<br />
the pumped liquid around the stator housing and back<br />
to the pump housing via internal channels.<br />
For external cooling the cooling jacket is fitted with<br />
sockets for pipe connections.<br />
The cooling jacket is required for cooling of the motor in<br />
dry installations, and in submerged installations if the<br />
pump is not completely submerged during continuous<br />
operation.<br />
The inlet side of the pump housing is fitted with a<br />
replaceable neck ring.<br />
57