Kiswire - Steel wire rope

More documents

Recommendations

Info

3. Ocean-going tugs Towing ropes 6WS(36) + FC or IWRC Mooring ropes 624 + 7 FC (For automatic mooring installations) 6WS (36) + FC 4. Fishing industry 6WS(26) + FC 6FI(25) + FC Oil Industry 1. Cable tool drilling lines 6SL(19) + FC 2. Water well drilling lines 6FI(25) + FC 3. Coring, sand, and swabbing lines 67 + FC 4. Casing lines 619 class + IWRC 5. Rotary drilling lines 6S(19) + IWRC 6WS(26) + IWRC 6. Winch lines 619 class + IWRC 6WS(31) + IWRC 624 + 7 FC 6WS(31) + FC 7. Tong or jerk lines 637 class + FC 8. Cathead lines 637 class + FC or IWRC 9. Tubing and sucker rod lines 6WS(26) + IWRC, 6WS(31) + IWRC 187 10. Pumping unit or horsehead lines 619 class + FC or IWRC 637 class + FC or IWRC 11. Mast raising(swing) lines 619 class + IWRC 637 class + IWRC Mining Industry 1. Shaft hoisting ropes Shallow vertical shafts 6FI(25) + FC Deep vertical shafts 6FI(25) + FC Inclined shaft ropes 6S(19) + FC 2. Slope and inclined plane ropes 6S(19) + FC 67 + FC 3. Shaft sinking and counterweight ropes 187 4. General haulage ropes 67 + FC, 6S(17) + FC 5. Mining machine ropes Head or pull and tail ropes 6FI(29) + IWRC, 6S FI(36) + IWRC 6FI(25) + IWRC Head or pull ropes 637 class + IWRC 6. Slusher and scraper ropes 6S(19) + IWRC, 3S(19) 7. Tugger hoist ropes 6S(19) + IWRC 8. Car puller, spotter, retarder ropes 6FI(25) + IWRC, 6S(19) + FC 9. Koepe or friction hoist ropes Tail or balance ropes Non-rotating 357(WA) Guide strand Lock-coil track strand 12 | Steel Wire Rope
11. Handling and Care of Wire Ropes Ropes should be stored in a clean dry place under cover. Reels or coils should be kept off the ground and supported by timber. They should also be examined periodically and rope dressing renewed as required. 1) Unreeling and Uncoiling Reels should be mounted on jacks and care taken to see that the reel rotates as the rope unwinds. Timber should be applied as a lever to one of the flanges to act as a brake, keeping the rope tight and preventing the reel from overrunning. When the ropes are supplied in coils a turntalbe or swift should be employed and the free end pulled out with event tension as the swift, or turnatable revolve. Over-winding should be avoided at all times to obviate kinking. Coils may also be unwound by securing the free outside end of the rope and then rolling the coil along the ground; care being taken at all times to ensure that the coil is held firmly together, avoiding tight coils or kinks. METHOD OF UNCOILING SMALL COIL METHOD OF UNCOILING LARGE COILS CORRECT CORRECT INCORRECT INCORRECT CORRECT 2) Seizings It is important that before cutting ropes are properly seized with annealed mild steel wire or strand to avoid slack wires and possible rope distortion. Steel Wire Rope | 13
Page 3 and 4: ELEPHANT around the world As a lead
Page 5 and 6: GENERAL INFOMATION ON WIRE ROPE for
Page 7 and 8: LUBRICATION Type of Lubrication Lub
Page 9 and 10: 8. GRADES OF WIRE ROPE Elephant Bra
Page 11: 2. Clamshell Holding and closing li
Page 16 and 17: For Mining Aerial Tramway. Stay. et
Page 18 and 19: For Crane, Hoist and General Engine
Page 20 and 21: For Crane, Hoist and General Engine
Page 22 and 23: Construction : 6Strands 19, 25, 26
Page 24 and 25: Construction : 6Strands 29, 31, 36,
Page 26 and 27: A Future That Is Open to the World

Kiswire - Steel wire rope

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?