subchapter c -- federal hazardous substances act regulations

More documents

Recommendations

Info

$,â\ soAPS - The American Cleaning Institute$

16 CFR Ch. II (1–1–05 Edition) – proposed modification – 6/25/06 which is fitted a cover. A thermometer is embedded in the block. (ii) The cover is fitted with an opening slide and a device capable of inserting an ignition flame (diameter 4±0.5 mm) into the well when the slide device shall intersect the plane of the underside of the cover. The cover is also provided with an orifice extending into the sample well for insertion of the test sample and also a suitable clamping device for securing the cover tightly to the metal block. The three openings in the cover shall be within the diameter of the sample well. When the slide is in the open position, the two openings in the slide shall coincide ex<strong>act</strong>ly with the two corresponding openings in the cover. (iii) Electrical heaters are attached to the bottom of the cup in a manner that provides efficient transfer of heat. An electronic heat control is required to hold the equilibrium temperature, in a draft-free area, within 0.1 °C (0.2 °F) for the low-temperature tester. A visual indicator lamp shows when energy is or is not being applied. Energy may be supplied from 120 or 240 V, 50 or 60 Hz main service. (2)(i) Test flame and pilot flameregulatable test flame, for dipping into the sample cup to try for flash, and a pilot flame, to maintain the test flame, are required. These flames may be fueled by piped gas service. A gage ring 4mm ( 5 / 32 in.) in diameter, engraved on the lid near the test flame, is required to ensure uniformity in the size of the test flame. (ii) Caution: Never recharge the selfcontained gas tank at elevated temperature, or with the pilot or test flames lighted, nor in the vicinity of other flames. (iii) Audible Signal is required. The audiable signal is given after 1 min in the case of the low-temperature tester. (iv) Syringe. 2ml capacity, equipped with a needle suitable for use with the apparatus, adjusted to deliver 2.00±0.05 ml. (3) Essential dimensions of the test apparatus are set forth in table 3. (n) Testing high-viscosity liquids. (1) Highviscosity materials may be added to the cup by the following procedure: (i) Back load a 5 or 10-ml syringe with the sample to be tested and extrude 2 ml into the cup. Spread the specimen as evenly as possible over the bottom of the cup. (ii) If the sample cannot be loaded into a syringe and extruded, other means of adding -- 46 -- the sample to the cup may be used such as a spoon. Add approximately 2 ml of material to the spoon and then push the material from the spoon into the cup. (iii) If the test specimen does not close the sampling port in the cup, seal the cup externally by suitable means. (2) Using the appropriate procedure, either Method A in §1500.43a(i) or Method B in § 1500.43a(j), determine the flashpoint of the specimen which has been added to the tester in accordance with § 1500.43a(n)(i), except that the time specified is increased from 1 to 5 minutes for samples at or above ambient temperature.
16 CFR Ch. II (1–1–05 Edition)—proposed modificication – 6/25/06 § 1500.44 Method for determining extremely flammable and flammable solids. To classify a flammable solid, the test method N.1 as described in Part III, subsection 33.2.1 of the UN Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria should be performed. The -- 47 --
Page 1 and 2: 16 CFR Ch. II (1-1-05 Edition) - pr
Page 3 and 4: (6)(i) Highly toxic means any subst
Page 5 and 6: involved presents an imminent hazar
Page 7 and 8: experimental animals in which signi
Page 9 and 10: (A) Flammable gas, Category 2: Gase
Page 11 and 12: limited to, a garage, carport, barn
Page 13 and 14: ingestion, such products shall be l
Page 15 and 16: Use only under [close] adult superv
Page 17 and 18: containers intended for sale as art
Page 19 and 20: conforming to paragraph (b)(8)(i)(E
Page 21 and 22: (B) For purposes of LHAMA enforceme
Page 23 and 24: (iii) Since the Commission has issu
Page 25 and 26: foam and on grass. No other data ar
Page 27 and 28: uises, or other injuries to fingers
Page 29 and 30: (18)(i) Any bunk bed (as defined in
Page 31 and 32: as well as to any outer container o
Page 33 and 34: 16 CFR Ch. II (1-1-05 Edition)—pr
Page 37 and 38: eactions are evaluated on the basis
Page 39 and 40: °F. divisions, and conforming to t
Page 41 and 42: Correction = (X + Y) / 2. Where: A=
Page 43 and 44: temperature. Advance the knob clock
Page 45: valve and ignite the pilot and test
Page 49 and 50: conditions in accordance with the m
Page 51 and 52: (ii) Part of the test sample may ne
Page 53 and 54: Such articles manufactured outside
Page 55 and 56: test for compliance with the regula
Page 57 and 58: § 1500.50 Test methods for simulat
Page 59 and 60: 30 cycles at a rate of one cycle pe
Page 61 and 62: (3) Testing procedure. Except as pr
Page 63 and 64: free, as specified by paragraphs 1.
Page 65 and 66: when its label fails to bear inform
Page 67 and 68: grams per kilogram of body weight o
Page 69 and 70: on individual containers carefully.
Page 71 and 72: coatings, and similar products, are
Page 73 and 74: panel in conspicuous type size the
Page 75 and 76: prevent the knot from slipping out
Page 77 and 78: this section shall promptly notify
Page 83 and 84: (1) Area of principal display panel
Page 85 and 86: hazardous substances to which label
Page 87 and 88: otherwise provided pursuant to sect
Page 89 and 90: animals described below. This categ
Page 91 and 92: (iv) ”Limited evidence” from an
Page 93 and 94: should be made on the basis of well
Page 95 and 96: chargeable with violations of secti
Page 97 and 98:
16 CFR Ch. II (1-1-05 Edition)—pr
Page 99 and 100:
matters relevant to the admissibili
Page 101:
Page 48: [1] Deleted Author (a) Equ
show all

subchapter c -- federal hazardous substances act regulations

Create successful ePaper yourself

Delete template?

Save as template?