Download the Full PDF Catalog - Schlueter Dairy Technologies
Download the Full PDF Catalog - Schlueter Dairy Technologies
Download the Full PDF Catalog - Schlueter Dairy Technologies
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
MilkTanksandCoolingSystems<br />
Safgard Tube Coolers<br />
• Heat Exchanger is offered in four models<br />
• All units have threaded S.S. water inlet & outlet nipples.<br />
Models 1000-2000 have 1” nipples.<br />
Model 2500 has 1-1/4”nipples.<br />
MILK IN<br />
Model 3000 has 2” nipples<br />
• All units 10 feet long<br />
• All milk tubes - 304 S.S.<br />
• Always install water inlet on opposite end of milk entry<br />
pointing downward to force air out & eliminate air pockets.<br />
• Slope units at least 1/16” per ft. up to 3/4” per 10’ section.<br />
• Reduce electrical energy costs up to 30% or more.<br />
• Use eccentric drain for proper discharge drainage<br />
HIGH END<br />
WATER OUT<br />
PITCH UPWARD<br />
1/16” PER FOOT<br />
2” X 10 FT.<br />
MILK OUT<br />
Mo d e l Tube Size # Tubes Co o l Rate @ 55° Part #<br />
2000-14 2” 14 4.5 GPM 47368<br />
3000-30 3” 30 6.5 GPM 47371<br />
Note: Cooling rates based on 2 gallons of water per 1 gallon of milk<br />
WATER IN<br />
Safgard Commerical Duty Plate Coolers - Rated upto 150 psi.<br />
Safgard model #S-8<br />
End Milk Approx.<br />
Part # Plates / Pass Plate Cap. Dry Wt.<br />
47317 25 Plate / Single Stainless .65 gal. 200 lbs.<br />
47318 45 Plate / Single Stainless 1.45 gal. 224 lbs.<br />
47319 25 Plate / Single Powder Coat .65 gal. 200 lbs.<br />
47320 45 Plate / Single Powder Coat 1.40 gal. 224 lbs.<br />
47317-1 Plate Only 1.3 lbs.<br />
47317-2 Gasket only<br />
Safgard Commercial Duty Powder Coated series heat<br />
exchangers w/Std floor frame #S-20<br />
End Milk Approx.<br />
Part # Plates / Pass Plate Cap. Dry Wt.<br />
47321 35 Plate / Single Powder Coat 2.5 gal. 558 lbs.<br />
47322 77 Plate / Single Powder Coat 5.4 gal. 665 lbs.<br />
47323 99 Plate / Single Powder Coat 6.8 gal. 737 lbs.<br />
47321-1 Plate Only 2.8 lbs.<br />
47321-2 Gasket only<br />
Safgard Commercial Duty Stanless Steel series heat<br />
exchangers w/Std floor frame #S-20-S<br />
End Milk Approx.<br />
Part # Plates / Pass Plate Cap. Dry Wt.<br />
47324 35 Plate / Single Stainless 2.5 gal. 788 lbs.<br />
47325 77 Plate / Single Stainless 5.4 gal. 905 lbs.<br />
47326 99 Plate / Single Stainless 6.8 gal. 967 lbs.<br />
Commercial Duty and Model S-8 and S-20 Features:<br />
• Reinforced Inlet<br />
• <strong>Full</strong> Drain Leak Detect<br />
• Strong Metal, Plate to Plate Alignment Device<br />
• Improved Heat Transfer<br />
• <strong>Full</strong>y Sanitary, meets current 3A/FDA Requirements<br />
• Titanium and Alternate Alloy Plates Available<br />
• Standard, High Tempature Nitrile, EDPM and Fluorocarbon<br />
(Viton®) Materials<br />
Commercial Duty and Model S-8 and S-20 Features:<br />
• Increased Efficiency<br />
• Higher pressure design - 150 psi.<br />
• <strong>Full</strong> Metal-to-Metal alignment to prevent plate shifting<br />
• Strong Side Band Gasket Groove Support<br />
• Improved Leak Detect Meets current 3A Sanitary standard 11-05<br />
• Wide Gap to Resist Fouling<br />
• Available Standard AISI 316 S.S. (22 ga.) Thickness<br />
(alternative alloys available)<br />
Janesville, WI 800.359.1700 • Fresno, CA 800.359.1702 • York, PA 800.359.1701 schlueterco.com 96