Section F â Air Atomizing Spray Nozzles - Spraying Systems Co.

Section F – Air Atomizing Spray Nozzles 

Overview 

If your application requires air atomizing nozzles, you’ll find 

information on the largest selection in the industry available in 

this section. Choose from dozens of nozzle bodies, assemblies and 

spray set-ups to get the precise performance you require. 

Air atomizing nozzles require a single air source for the atomizing 

air. Some versions, equipped with a cylinder for automatic 

operation or clean-out and shut-off needles, may require an 

additional air line. Fluid lines are required for all models. The fluid 

line can be pressurized or supplied using a siphon- or gravityfed 

configuration. It is recommended that air and fluid lines are 

equipped with the proper filters, regulators and valves. 

Air atomizing nozzles require spray set-ups. Each set-up consists 

of an air cap and fluid cap and some may also include O-rings 

and retainer caps. You can select from a wide assortment of 

capacities, spray patterns and pressure- or siphon-fed set-ups. 

• Product Range: 

– 1/8J and 1/4J Series nozzles are available in many 

configurations and operate at standard flow rates. Ranges 

from: 0.55 to 58.1 gph at 40 psi (2.08 to 220 l/h at 2.8 bar). 

– Variable spray nozzles provide independent control of liquid, 

atomizing air and fan air pressure for fine tuning of flow rate, 

drop size, spray distribution and coverage. 

– 1/2J Series nozzles offer the same features and benefits as 

1/8J and 1/4J Series but operate at higher capacities. Ranges 

from: 22.2 to 222 gph at 40 psi (84 to 840 l/h at 2.8 bar). 

– 1J Series nozzles offer the highest flow rates available. Ranges 

from: 120 to 906 gph at 40 psi (454 to 3430 l/h at 2.8 bar). 

Additional information can be found in Section G, Automatic Spray 

Nozzles and in Section K, Special Purpose Spray Nozzles. 

Air Atomizing Spray Nozzles 

Table of Contents 

Basic Information 

Set-ups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F3 

Features .................................................. F4 

1/8J and 1/4J Series 

Overview/Nozzle Bodies/Nozzle Assemblies . . . . . . . . . . . . . . . . . . F5 

Pressure Spray Set-ups, Internal Mix . . . . . . . . . . . . . . . . . . . . . . . . F9 

Pressure Spray Set-ups, External Mix ....................... F15 

Pressure Spray Set-ups, Internal Mix, 

High Transfer Efficiency (HTE) .............................. F19 

Siphon/Gravity-Fed Spray Set-ups, External Mix .............. F23 

1/8JJ Compact Series 

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F25 

Nozzle Bodies/Nozzle Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . F26 

Pressure Spray Set-ups, Internal Mix . . . . . . . . . . . . . . . . . . . . . . . F27 

Pressure Spray Set-ups, External Mix, High Capacity . . . . . . . . . F31 

Pressure Spray Set-ups, Internal Mix, Air Efficient . . . . . . . . . . . F33 


Variable Spray Series 

Variable Spray Nozzles .................................... F36 


1/2J Series 





Air Atomizing 

Nozzles 

Air atomizing caps 

1J Series 





Special Purpose 

AirJet ® Fogger Spray Nozzles .............................. F54 

DripSafe AirJet Fogger Spray Nozzles ..................... F56 

Humidification Spray Nozzles and Units . . . . . . . . . . . . . . . . . . . . . F58 

Humidification System Components. . . . . . . . . . . . . . . . . . . . . . . . . F60 

Air Atomizing Accessories ................................. F61 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 

Visit Our Web Site: www.spray.com, Email: info@spray.com 

F1

Air Atomizing Spray Nozzles 

Air Atomizing Nozzles 

Optimization Tips 

• Reduce installation time by using split-eyelet connectors on both the air 

and fluid lines. Split-eyelet connectors only require a hole drilled into the 

pipe, eliminating the need for cutting, threading and brazing operations. 

• To eliminate the unintentional release of non-atomized liquid, use a check 

valve to shut down liquid flow if no air pressure is detected. 

• Use air atomizing nozzles with clean-out needles to eliminate clogging and 

ensure optimum performance. 

• Use strainers and air filters to ensure optimum performance. 

• If positive shut-off is required, use Drip Free set-ups with JAU nozzles. 

• Use a heat jacket with VAU/VMAU variable spray nozzles to keep viscous 

liquids warm and transferable. 

• When adjusting air pressure with internal mix nozzles, do not exceed 

recommended values as it may result in choking liquid flow. Increasing 

liquid flow can also choke air flow. 

• For optimal control of your air atomizing spray system, the use of an 

AutoJet ® Spray System helps conserve liquid usage and reduces scrap by 

monitoring and automatically adjusting spray pattern, flow rate, drop size, 

liquid pressure and atomizing air pressure. 

AutoJet Spray Controllers 

and Systems 

Air atomizing nozzles 

with clean-out needles 

Heat jackets 

Spray nozzles 

Hot fluid 

flow channel 

Cut out view of heat jacket 

showing unique flow channel 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F2

Set-ups, Basic Information 

• Liquid can be supplied to the nozzle under pressure or it can be supplied through a liquid siphon or gravity-feed. 

Pressure Spray Set-ups 

Siphon/Gravity-Fed Spray Set-ups 

• Liquid is supplied to the nozzle under pressure. 

• Air and liquid can be externally or internally mixed to produce a 

completely atomized spray. 

– 1/8J and 1/4J Series 

Pages F5 – F18 

– 1/2J Series 


– 1J Series 


– Compact 1/8JJ Series 


– Variable 1/8VAA Series 


• New High Transfer Efficiency (HTE) external mix air atomizing 

set-ups recently introduced for 1/4J Series. 

– Pages F19 – F22 

• Liquid is supplied via liquid siphon or is gravity-fed. 

• Designed to draw liquid through the feed line into the air flow 

where it is atomized. 

– 1/8J and 1/4J Series 


– Compact 1/8JJ Series 


– 1/2J Series 

Page 49 

– 1J Series 

Page 53 



1/4JN 

air 

atomizing 

nozzle 

Air pressure 

regulator 

with gauge 

Air shut-off valve 

Air filter 

Air 

inlet 

Liquid 

inlet 

Liquid 

shut-off valve 

Air pressure regulator 

with gauge 

1/4JN 

air atomizing 

nozzle 

Siphon 

tube 

Siphon 

height 

Air shut-off valve 

Air filter 


inlet 

Liquid pressure regulator 

with gauge 

TW 

liquid strainer 

Liquid 

container 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F3

Features, Basic Information 


Spray Set-up Features 

• Each series is available with a pressure spray set-up or siphon 

spray set-up. 

• Each set-up provides a specific spray pattern with a specific 

capacity and spray coverage range performance. 

• Spray set-ups are interchangeable for each nozzle series. 

– Round spray: Extended full cone round spray pattern. 

– Wide angle round spray: Hollow cone-type, wide angle round 

spray pattern. 

– 360° circular spray: Hollow cone-type 360° circular spray pattern. 

– Flat spray: Extended flat or sheet-type spray pattern. 

– Deflected flat spray: Extended flat or sheet-type spray diverted 

away from the axis of the inlet connection. 

• Each spray set-up consists of an air cap and fluid cap. 

• For more information request Data Sheets 10616 and 10616-1. 

Atomization Control Features 

• Achieved by adjusting the air and liquid pressure in the spray 

set-up. 

• Obtaining finer atomization is accomplished by increasing the 

air pressure and/or lowering the liquid pressure, resulting in a 

high ratio of air flow rate to liquid flow rate. 

External mix with pressure set-ups: Flat and round spray patterns. 

Air cap 

Fluid cap 

Internal Mix Features 

• Liquid and air are mixed internally to produce a completely 

atomized spray. 

• Liquid and gas streams are not independent and a change in air 

flow will affect the liquid flow. 

• Internal mix uses pressure set-ups and is available with the 

following spray patterns: 

– 360° circular spray. 

– Deflected flat spray. 

– Elliptical spray. 

– Flat spray. 

– Round spray. 

– Wide angle round spray. 

External Mix Features 

• Liquid and air streams are mixed outside of the nozzle. 

• Air and liquid flow can be controlled independently. 

• Effective for higher viscosity liquids and abrasive suspensions. 

• External mix can use siphon set-ups or pressure set-ups. 

• When a siphon set-up is used, a round spray pattern is produced. 

• When a pressure set-up is used, a flat spray pattern is produced. 

Internal mix with 

pressure set-ups: 

Round spray patterns 

Internal mix with 


Flat spray patterns 

External mix with 

siphon set-ups: 

Round spray patterns 

External mix with 


Flat spray patterns 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F4

Overview/Nozzle Bodies/Nozzle Assemblies, 


1/8J and 1/4J Series air atomizing 

1/8J, 1/4J 

Spray set-up for HTE 

Plug CP1159 

1/8JN, 1/4JN 

1 2 3 

Spray set-up 

Shut-off 

needle assembly 12810 

1/8JCO, 1/4JCO 

11005–1/8J, 11005–1/4J 

1 2 3 4 

1. Retainer ring CP1158 

2. Air cap 

3. Fluid cap 

4. Fluid cap gasket CP3612 

5. Nozzle body CP1151 

6. Back seal gasket CP10439 

Spray set-up for Drip Free 

5 

6 

Clean-out 


Shut-off/clean-out 




1/4JAU – Drip Free 

1 2 3 

4 


needle assembly 

Features and Benefits 

• The basic J Series nozzle assembly consists of a body and a 

spray set-up. 

• Various assemblies can be added to provide shut-off and 

clean-out functions. 

• 1/8J and 1/4J bodies have liquid and air feeds at opposite ends 

of the body. 

– Bodies are provided with a removable plug so other needle 

assemblies may be added in the future. 

• JN features a manual shut-off needle that enables the flow of 

liquid to the nozzle to be stopped. 

• JCO features a clean-out needle that is activated manually. 

– The needle slides through the liquid orifice to clear 

obstructions. 

– Ideal for intermittent spraying applications when liquid can 

dry in the orifice between uses. 

• 11005 combines the features of JN and JCO offering a 

combination shut-off/clean-out needle. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F5

Nozzle Bodies/Nozzle Assemblies, 



1/8J, 1/4J 

1/8" and 1/4" NPT or BSPT 


• See page F2 for optimization tips. 

1/8JN, 1/4JN 

1/8" and 1/4" NPT or BSPT with 

shut-off needle 

1/8JCO, 1/4JCO 

1/8" or 1/4" NPT or BSPT with 

clean-out needle 

See Also 

• Accessories 

– Air line filters 

– Air pressure regulators 

– Liquid pressure regulators 

11005-1/8J, 1/4J 

1/8" or 1/4" NPT or BSPT with 

shut-off/clean-out needle 

– Pressure gauges 

– Solenoid valves 

– Strainers 

http:// 

Materials 

Ordering Info 

Material 

Nozzle Bodies 

Electroless Nickelplated 

Brass 

Material 

Code 

Nozzle Type 

J JN JCO 11005 

(none) l l l l 

303 Stainless Steel SS l l l l 

Lucite ® * LUC l 

Spray Set-ups 

Lucite* LUC l 


Brass Air 

Cap and 

303 Stainless Steel 

Fluid Cap 

SSBR l l l l 

303 Stainless Steel SS l l l l 

*May not be available for all spray set-ups listed. 

Other materials available upon request. 

Complete Nozzle Assembly 

Nozzle Body* 

*Includes retainer and gasket. 

Spray Set-up 

1/4 JN – SS + SU11DF – SS 

l l l l l 

Inlet 

Conn. 

Nozzle 

Body 

Assembly 

Type 

Material 


Spray 

Set-up 

No. 

Material 


BSPT connections require the addition of a “B” prior to 

the nozzle body inlet connection. 

To order fluid cap only, use fluid cap number (shown in 

performance data charts) and material code: 2050-SS. 

To order air cap only, use air cap number (shown in 


To order spray nozzle without set-up, use inlet 

connection, nozzle body and material code: 1/4JN-SS. 

Spray Set-up Only 


SU11DF – 

l 


Set-up 

No. 

To order spray set-up 

only, use spray set-up 

number and material 

code: SU11DF-SS. 

SS 

l 

Material 


Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F6




• 1/4JF features a built-in liquid strainer. 

• 1/4JFN features built-in liquid strainer and liquid shut-off needle. 

• JBC features the center lines of the air and liquid inlet entering in 

the back of the nozzle and parallel to the spray projection axis. 

• JAC features air and liquid inlet connections entering the nozzle at 

90° to spray projection axis. 

• JACN features air and liquid inlet connections entering the nozzle 

at 90° to spray projection axis and a shut-off needle. 

• 1/8-2JAC dual spray assembly features two opposing spray 

set-ups with the air and liquid inlet connections perpendicular 

to the spray axis. 

• The 7545 multiple swivel spray assembly features each spray 

set-up mounted on its own swivel body. 

– One or two bodies may be used and each can be rotated 360° to 

the desired position. 

– Swivel bodies are locked in place by a stainless steel lock screw 

that runs vertical through the assembly. 

• 6552-1/8JAC miniature assembly body is only 1/2" (13 mm) thick 

with a 1-5/32" (29 mm) by 1-1/4" (32 mm) rectangular face. 

– The tip of the nozzle projects from the face a maximum of 

1-3/16" (30 mm) depending upon the spray set-up used. 

• 1/4JBCJ features a steam jacket around the nozzle body for 

spraying liquids that are too viscous to spray at room temperature. 

With Strainer 

Back Connect 

Top Inlet 

Top Inlet 

1/4JF and 1/4JFN 

1/4" NPT or BSPT (F) 

air inlet connection 


liquid inlet connection 

1/8JBC and 1/4JBC 

1/8" or 1/4" NPT or BSPT (F) 

inlet connection 

1/8JAC, 1/8JACN 

1/4JAC, 1/4JACN 

1/8" or 1/4" NPT or BSPT (F) 


1/8-2JAC 





Swivel 

Miniature 



See Also 

http:// 

7545 

1/8" NPT or BSPT (F) air and 


Steam Jacket 

1/4JBCJ 


inlet/outlet connection 

6552-1/8JAC 






– Liquid pressure regulators – Strainers 

• For JBC, request Data Sheets 4921, 6885 and 6185 

• For JAC and JACN, request Data Sheets 4922 and 4922-1 

• For 1/8-2JAC dual spray assembly, request Data Sheet 6497 

• For 7545 multiple swivel spray assembly, request 

Data Sheet 7545 

• For 6552-1/8JAC, request Data Sheet 6552 



• For 1/4JBCJ, request Data Sheets 4610 and 6331 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F7





• 8650 multiple spray assembly (cluster type) features five spray 

set-ups located on the faces of the assembly or four set-ups 

located on the side faces. 

• 2J is a dual spray assembly with opposing spray set-ups 

perpendicular to opposing air and liquid inlets. 

• Thin wall adapters add an adapter locknut and gasket to CP3376 

thick wall adapters to provide secure mounting in thin walls and 

include CP6378 locknut and CP2804-3 gasket. 

• Thick wall adapters replace retainer rings on nozzle assemblies 

and fit into threaded wall openings, holding the nozzle securely 

in place. 

• 1/4JDLN and 1/4JDLCO feature a screw mount with 9/32" (7 mm) 

diameter mounting holes. 

– Standard 1/4" (6 mm) screws hold the body to the wall with a 

gasket providing the seal. 

– The 1/4JDLN features a shut-off needle and the 1/4JDLCO 

features a clean-out needle. 

• 20470 Series hand-held air atomizing spray guns feature 

lightweight aluminum construction and a comfortable, 

easy-to-operate design. 

– Extensions are available in up to 36" (91 cm) lengths. 

Cluster Type 

Twin Spray 

Thin Walls 

Thick Walls 

8650 



2J 



Available for 1/8J and 1/4J 

assemblies 

1/8J and 1/4J with 3/4" NPT or 

BSPT (M) adapter connection 

Screw Mount 





20470 

Hand-held spray gun 

1/4" NPT or BSPT (F) inlet connection 

See Also 







• For 8650 multiple spray assembly, request Data Sheet 8650 

• For 2J, request Data Sheets 5356 and 6530 

• For thin wall adapters , request Data Sheet 3378 

• For thick wall adapters, request Data Sheets 3378, 7003 

and 7323 

• For 1/4JDLN and 1/4JDLCO, request Data Sheet 7690 

• For 20470 Series hand-held air atomizing spray guns, 

request Data Sheets 20470J, 20470JN, 20470JMCO, 

20470JN-1, 20470JJ, 20470JJN and 20470JJNTK 

http:// 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F8



Air Caps 

Round spray air caps 

produce a narrow, full cone 

round spray pattern 


• For round spray pattern, angle “A” is maintained throughout distance “B”. Beyond “B”, the spray 

becomes turbulent and will project out to distance “D”. 

• When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. 

• The liquid and compressed air or gas are mixed internally to produce a completely atomized spray. 


Fluid cap 

Round spray 

pattern 

A 

Performance Data 

D 

1158 retainer ring and 3612 gasket must be ordered separately from the spray set-up, but are included in 

the standard nozzle assembly. Please contact your sales engineer. 

B 

1158 retainer ring 

3612 

gasket 



Round Spray 


Set-up 

No. 

SU11 


Set-up 

Consists of 

Fluid and 

Air Cap 

Combination 

Fluid Cap 

2050 

+ 


67147 


Press. 

*At the stated pressure in bar. 

Liquid Capacity (liters per hour)* and Air Capacity (liters per minute)* 

Liquid Pressure 

0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.70 2.5 15.6 1.1 6.4 11.9 1.4 6.4 13.9 2.7 6.2 23 3.5 7.8 28 

.85 1.8 19.0 1.4 5.0 15.0 1.7 5.5 16.7 2.8 5.7 25 3.7 7.3 29 

1.0 1.4 22 1.7 4.1 18.7 2.0 4.5 19.8 3.0 5.2 27 3.9 6.4 33 

– – – 1.8 3.4 20 2.2 3.4 24 3.1 4.7 29 4.2 5.5 38 

– – – 2.0 3.0 23 2.4 3.0 26 3.2 4.3 31 4.5 4.5 43 

– – – 2.1 2.6 25 2.5 2.5 28 3.4 3.9 33 4.6 4.1 45 

– – – 2.2 2.0 27 2.7 2.3 31 3.7 3.0 38 4.8 3.7 47 

Add DF to part number for “Drip Free” set-ups. Example: SU11DF. 

l/h 


l/min 

Air* 

.85 

1.7 

2.5 

3.1 

4.5 

Liquid* 

.70 

1.5 

2.0 

3.0 

4.0 


Dimensions 


Angle 

A (°) 

13 

13 

13 

14 

15 

B 

(cm) 

30 

33 

36 

39 

44 

D 

(m) 

2.7 

3.0 

3.4 

3.8 

4.4 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F9







Set-up 

No. 

SU12A 


Set-up 


Fluid and 



Fluid Cap 

2050 

+ 


73160 


Press. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.70 2.5 18.7 1.4 5.7 27 1.7 6.7 29 2.2 9.2 34 2.8 11.9 39 

.85 2.0 22 1.5 5.2 29 1.8 6.4 31 2.5 8.2 39 3.1 11.0 43 

1.0 1.6 26 1.7 4.8 32 2.0 5.9 34 2.8 7.2 44 3.4 10.1 47 

– – – 1.8 4.3 35 2.1 5.2 37 3.0 6.7 47 3.7 9.2 52 

– – – 2.0 3.9 37 2.2 4.8 40 3.1 6.3 49 3.9 8.4 58 

– – – 2.1 3.4 40 2.4 4.3 43 3.2 5.9 52 4.2 7.6 62 

– – – – – – 2.7 3.6 48 3.4 5.5 55 4.5 6.8 68 

l/h 


l/min 


.85 

1.5 

2.4 

3.0 

3.9 

Liquid* 

.70 

1.5 

2.0 

3.0 

4.0 


Dimensions 


Angle 

A (°) 

12 

13 

13 

13 

15 

B 

(cm) 

43 

46 

48 

51 

56 

D 

(m) 

3.7 

4.0 

4.3 

4.6 

5.2 

SU12 

Fluid Cap 

2850 

+ 


73160 

.85 4.8 21 1.7 8.4 31 2.0 10.7 33 2.7 16.5 37 3.4 20 43 

1.1 4.1 27 1.8 7.5 35 2.1 9.8 37 2.8 15.4 38 3.7 18.4 47 

1.4 3.4 33 2.0 7.0 37 2.4 8.2 42 3.1 13.6 43 3.9 16.8 50 

1.5 3.1 35 2.2 5.7 44 2.7 6.8 48 3.4 11.8 49 4.2 15.2 55 

1.7 3.0 39 2.5 4.8 49 3.0 5.9 55 3.7 10.4 55 4.5 13.8 60 

1.8 2.9 41 2.8 4.1 54 3.2 5.0 59 3.9 9.1 61 4.8 12.4 65 

2.0 2.8 44 3.1 3.6 59 3.5 4.1 65 4.2 7.9 65 4.9 11.8 68 

1.5 

2.5 

3.0 

3.4 

4.2 

.70 

1.5 

2.0 

3.0 

4.0 

12 

13 

13 

14 

15 

48 

51 

53 

56 

60 

4.0 

4.3 

4.6 

4.9 

5.3 

SU22B 

Fluid Cap 

40100 

+ 


1401110 

1.1 13.0 76 2.2 17.8 116 2.8 20 136 3.4 32 149 4.6 37 193 

1.4 8.9 91 2.5 13.1 130 3.1 16.3 149 3.9 25 170 5.3 29 220 

1.5 7.2 98 2.8 9.5 143 3.4 11.9 163 4.6 15.9 205 5.6 25 235 

1.7 5.8 105 3.1 7.0 157 3.9 7.0 187 5.3 9.1 240 6.0 21 250 

1.8 4.7 112 3.4 4.9 171 4.2 4.7 205 5.6 6.8 255 6.3 17.4 270 

2.0 3.6 119 3.5 4.2 178 4.6 3.0 220 6.0 5.0 275 6.7 14.0 290 

2.1 2.7 127 – – – – – – 6.3 3.6 290 7.0 11.0 305 

1.7 

2.8 

3.9 

5.3 

6.0 

.70 

1.5 

2.0 

3.0 

4.0 

18 

20 

20 

21 

21 

66 

76 

81 

91 

97 

4.9 

6.1 

6.7 

7.9 

9.1 

SU22 

Fluid Cap 

60100 

+ 


1401110 

.85 31 57 1.4 61 69 2.1 53 96 2.7 80 103 3.8 88 135 

1.0 25 66 1.5 54 76 2.4 41 112 3.0 69 117 4.2 73 156 

1.1 18.5 75 1.7 48 85 2.7 31 127 3.2 59 130 4.6 61 176 

1.3 12.9 85 1.8 41 93 2.8 26 136 3.5 49 146 4.9 48 196 

– – – 2.0 35 102 3.0 22 144 3.7 44 154 5.3 39 215 

– – – 2.1 30 110 – – – 3.8 37 161 5.6 31 240 

– – – 2.2 25 119 – – – 3.9 35 170 6.0 23 260 

1.0 

1.8 

2.8 

3.5 

4.9 

.70 

1.5 

2.0 

3.0 

4.0 

17 

18 

20 

20 

21 

61 

69 

76 

79 

91 

4.9 

5.8 

6.7 

7.0 

8.5 

SU42 

Fluid Cap 

100150 

+ 


1891125 

1.0 44 86 1.4 125 79 2.0 123 108 2.2 199 88 3.0 250 99 

1.1 32 102 1.5 106 91 2.1 108 119 2.5 174 110 3.2 225 120 

– – – 1.7 87 105 2.2 95 130 2.8 146 133 3.5 205 141 

– – – 1.8 70 118 2.4 79 143 3.1 121 154 3.8 182 163 

– – – 2.0 55 130 2.5 64 155 3.2 108 166 4.1 159 184 

– – – – – – 2.7 52 166 3.4 95 176 4.6 121 225 

– – – – – – 2.8 42 178 3.5 84 187 4.9 93 255 

1.0 

1.7 

2.4 

3.1 

3.8 

.70 

1.5 

2.0 

3.0 

4.0 

19 

20 

21 

21 

22 

89 

99 

104 

107 

117 

6.1 

7.0 

7.6 

7.9 

9.1 


Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F10





Wide angle round spray and 

360° circular spray air caps 

produce hollow cone, wide 

angle round spray and 

360° circular spray patterns. 


Wide Angle Round Spray 


Set-up 

No. 

SU16 

SU26B 

SU26 


Set-up 


Fluid and 



Fluid Cap 

2050 

+ 


67-6-20-70° 

Fluid Cap 

40100 

+ 


140-6-37-70° 

Fluid Cap 

60100 

+ 


140-6-37-70° 


Press. 

• For wide angle round spray, dimensions “A”, “B” and “C” are the pattern widths at distances from 

the nozzle. 

• The total distance of spray projection from the nozzle to the maximum dispersal point is 

represented by “D”. 






0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 

Wide angle 

round spray pattern 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.60 5.3 10.2 1.1 8.1 13.3 1.5 8.1 16.4 2.4 8.9 22 3.1 10.5 24 

.70 4.3 12.2 1.3 7.0 15.0 1.8 6.6 21 2.7 8.1 26 3.4 9.7 28 

.85 3.0 14.2 1.4 6.4 17.0 2.1 4.9 25 3.0 6.4 30 3.9 7.8 36 

1.0 1.7 17.0 1.5 5.5 19.0 2.4 3.2 29 3.2 4.9 34 4.2 6.1 42 

– – – 1.7 4.5 22 – – – 3.4 4.2 37 4.6 4.4 47 

– – – 1.8 3.5 24 – – – 3.5 3.4 40 4.9 2.8 54 

.85 7.0 50 1.7 13.2 68 2.0 18.5 68 2.8 25 84 3.7 31 96 

1.0 2.1 62 1.8 9.8 79 2.1 15.1 76 3.0 22 92 3.8 28 105 

– – – – – – 2.2 11.7 85 3.1 18.5 101 3.9 26 113 

– – – – – – – – – 3.2 15.1 109 4.1 23 122 

– – – – – – – – – 3.4 12.1 119 4.2 20 130 

– – – – – – – – – 3.5 9.1 130 4.6 13.6 153 

– – – – – – – – – 3.7 6.1 142 4.9 6.8 183 

.70 24 32 1.4 43 37 2.1 33 66 2.8 52 65 3.7 63 68 

.85 13.6 44 1.5 35 49 2.2 26 78 3.0 46 76 3.8 58 79 

1.0 7.6 57 1.7 28 61 2.4 18.9 89 3.1 39 87 3.9 52 101 

– – – 1.8 21 71 2.5 11.7 100 3.2 33 99 4.2 41 111 

– – – – – – – – – 3.4 26 110 4.6 27 138 

– – – – – – – – – 3.5 19.5 122 4.9 15.9 166 

– – – – – – – – – 3.7 13.2 133 – – – 


D 

C 



B 

A 

6" 

(15 cm) 

9" (23 cm) 

15" (38 cm) 

l/h 




l/min 


.70 

1.4 

1.8 

3.0 

3.9 

.85 

1.7 

2.1 

3.2 

4.1 

.85 

1.5 

2.4 

3.2 

3.9 

Fluid cap 

Liquid* 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

3612 

gasket 


Dimensions 

A 

(cm) 

14 

15 

16 

16 

19 

18 

19 

19 

20 

21 

19 

20 

20 

20 

20 

B 

(cm) 

18 

19 

20 

20 

23 

24 

25 

25 

26 

28 

25 

27 

27 

28 

28 

C 

(cm) 

23 

24 

25 

26 

30 

31 

33 

33 

34 

37 

36 

37 

37 

38 

39 

D 

(m) 

1.5 

1.8 

2.1 

2.7 

4.0 

1.8 

2.4 

3.2 

4.1 

5.9 

2.1 

3.2 

4.1 

5.0 

6.8 



Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F11







Set-up 

No. 

SU29 


Set-up 


Fluid and 



Fluid Cap 

60100 

+ 


140-6-52-70° 


Press. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

1.3 36 85 2.1 57 116 3.1 53 156 4.2 64 197 5.6 74 245 

1.5 29 102 2.4 51 130 3.2 50 163 4.9 51 230 6.0 68 260 

1.8 23 117 2.7 45 143 3.4 47 170 5.6 40 265 6.3 62 280 

2.0 19.7 125 3.0 39 157 3.5 45 177 6.0 34 285 6.7 56 295 

2.1 16.7 133 3.2 33 170 3.9 38 194 6.3 28 300 7.0 51 315 

2.3 14.0 142 3.5 28 185 4.6 25 230 6.7 22 320 – – – 

2.4 11.4 149 4.2 13.6 220 4.9 18.5 245 7.0 17.8 335 – – – 

l/h 


l/min 

Air* Liquid* 

2.0 

3.0 

3.9 

6.0 

6.3 

.70 

1.5 

2.0 

3.0 

4.0 


Dimensions 

A' 

(cm) 

20 

20 

22 

23 

24 

B 

(cm) 

25 

27 

28 

29 

32 

C 

(cm) 

33 

34 

37 

38 

41 

D 

(m) 

5.5 

6.4 

8.2 

9.1 

10.4 

SU30 

Fluid Cap 

40100 

+ 


120-6-35-60° 

1.1 12.3 40 2.2 16.3 62 2.7 21 69 4.2 19.3 100 5.6 22 130 

1.3 9.9 45 2.5 12.1 71 3.0 16.3 78 4.6 14.6 113 6.0 17.6 142 

1.4 7.9 50 2.8 8.9 79 3.2 12.3 86 4.9 10.8 124 6.3 14.0 152 

1.5 6.1 54 3.0 7.6 83 3.4 10.7 91 5.3 8.1 135 6.7 11.4 163 

1.7 4.9 58 3.1 6.4 87 3.5 9.3 94 5.6 6.2 146 7.0 9.1 174 

1.8 3.9 62 3.2 5.5 91 3.9 6.4 105 6.0 4.9 157 – – – 

2.0 3.1 67 3.4 4.7 95 4.2 4.7 115 6.3 4.0 167 – – – 

1.5 

3.0 

3.4 

5.3 

6.3 

.70 

1.5 

2.0 

3.0 

4.0 

15 

16 

16 

18 

19 

19 

20 

20 

22 

24 

23 

24 

24 

25 

30 

2.7 

4.6 

5.5 

7.3 

9.4 

SU46 

Fluid Cap 

100150 

+ 


189-6-62-70° 

1.7 25 156 3.0 39 230 3.4 50 250 4.6 62 320 6.0 93 395 

1.8 19.7 167 3.1 33 240 3.5 43 260 4.9 47 345 6.3 77 425 

2.0 15.1 178 3.2 27 255 3.7 41 275 5.3 36 375 6.7 62 460 

2.1 11.4 193 3.4 23 265 3.9 27 300 5.6 26 405 7.0 52 495 

2.3 7.6 205 3.5 18.5 280 4.1 23 310 6.0 18.9 435 – – – 

– – – 3.7 14.8 290 4.2 18.9 320 6.3 13.6 460 – – – 

– – – – – – 4.4 15.9 335 – – – – – – 

2.0 

3.2 

3.9 

5.3 

6.3 

.70 

1.5 

2.0 

3.0 

4.0 

24 

25 

28 

29 

33 

33 

34 

37 

38 

42 

46 

47 

51 

53 

58 

5.5 

6.4 

7.3 

7.9 

9.8 


360° Circular Spray *At the stated pressure in bar. 


Set-up 

No. 

SU340C 


Set-up 


Fluid and 



Fluid Cap 

60150 

+ 


189-6-62- 

160HC 


Press. 



0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

1.4 15.1 69 2.8 19.5 142 3.5 21 185 4.2 48 210 6.0 45 340 

1.5 10.6 77 3.0 16.1 153 3.7 17.6 196 4.6 37 240 6.3 37 375 

1.7 7.6 84 3.1 13.2 165 3.8 14.8 210 4.9 28 275 6.7 30 405 

1.8 5.7 93 3.2 10.6 177 3.9 12.5 220 5.6 15.5 340 7.0 24 440 

2.0 4.2 103 3.4 8.3 188 4.2 8.1 245 6.3 7.8 425 – – – 


l/h 


l/min 

360° circular spray pattern 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F12




Flat spray and deflected flat 

spray air caps produce flat or 

deflected flat spray patterns. 


• For flat spray pattern, dimensions “A”, “B” and “C” are the pattern widths at distances from the 

nozzle. 





C 

B 

A 


Fluid cap 


Flat Spray 


Set-up 

No. 

SU13A 

SU13 

SUN13 


Set-up 


Fluid and 



Fluid Cap 

2050 

+ 


73328 

Fluid Cap 

2850 

+ 


73328 

Fluid Cap 

2850 

+ 


73335 


Press. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.70 5.5 24 1.3 9.1 31 2.0 8.6 42 2.7 11.2 52 3.9 12.0 69 

.85 4.7 27 1.5 7.7 36 2.2 7.5 47 3.0 10.1 56 4.6 9.7 81 

1.0 4.1 31 1.8 6.5 42 2.5 6.2 52 3.2 9.1 62 5.3 7.5 93 

l/h 


l/min 

1.1 3.5 34 2.1 5.4 47 2.8 5.2 57 3.5 8.1 66 6.0 5.3 104 

1.3 3.0 37 2.4 4.3 52 3.1 4.2 63 4.2 5.4 79 6.3 4.3 110 

1.4 2.5 40 2.7 3.3 57 3.2 3.7 65 4.6 4.2 85 6.7 3.3 116 

1.5 2.0 44 2.8 2.8 60 3.4 3.2 68 4.9 3.1 91 7.0 2.4 122 

.85 8.2 19.8 1.4 14.4 27 2.1 13.5 36 2.7 19.1 42 4.6 16.1 69 

1.0 6.8 23 1.7 11.9 32 2.4 11.4 42 3.0 17.1 46 4.9 13.8 76 

1.1 5.5 27 2.0 9.5 37 2.7 9.2 47 3.2 15.1 52 5.3 11.5 83 

1.3 4.1 30 2.1 8.3 40 3.0 7.1 53 3.5 13.1 57 5.6 9.3 90 

1.4 2.9 34 2.2 7.1 43 3.2 5.0 59 4.2 8.1 72 6.0 7.3 97 

– – – 2.4 6.1 46 3.4 4.0 63 4.6 5.9 79 6.3 5.6 104 

– – – 2.5 5.1 49 3.5 3.3 66 4.9 4.0 86 6.7 4.3 112 

1.0 9.0 25 2.0 10.4 41 2.4 11.6 48 3.1 15.6 56 4.2 17.1 73 

1.1 7.8 30 2.1 9.3 45 2.5 10.4 51 3.2 14.6 59 4.6 15.0 80 

1.3 6.6 32 2.2 8.2 48 2.7 9.4 54 3.4 13.7 62 4.9 12.8 87 

1.4 5.2 36 2.5 6.1 55 3.0 7.3 61 3.8 10.8 71 5.3 11.0 94 

1.7 3.1 44 2.8 4.3 62 3.2 5.5 68 4.2 8.5 82 5.6 9.4 103 

2.0 2.0 50 3.1 3.0 69 3.5 4.1 75 4.9 5.2 98 6.3 7.2 119 

2.2 1.1 56 3.4 2.0 75 3.8 2.9 81 6.0 2.3 120 7.0 6.1 134 


Flat spray 

pattern 

6" 

(15 cm) 

9" (23 cm) 

15" (38 cm) 



1.1 

2.1 

2.8 

3.5 

6.0 

1.1 

2.1 

3.0 

3.5 

5.6 

1.4 

2.5 

3.2 

3.8 

5.3 

Liquid* 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 


Dimensions 

A 

(cm) 

25 

36 

38 

47 

56 

36 

43 

51 

58 

58 

10 

13 

13 

15 

20 

3612 

gasket 

D 



B 

(cm) 

36 

48 

53 

61 

74 

46 

61 

66 

76 

76 

13 

15 

17 

22 

25 

C 

(cm) 

46 

66 

76 

86 

94 

71 

81 

89 

97 

97 

17 

20 

22 

28 

33 

D 

(m) 

2.6 

3.0 

3.2 

3.4 

4.0 

2.1 

2.4 

2.6 

2.7 

3.2 

3.0 

3.7 

4.0 

4.2 

4.8 



Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F13







Set-up 

No. 

SU14 

SUN23 

SU23B 

SU23 

SU43 


Set-up 


Fluid and 



Fluid Cap 

2850 

+ 


73320 

Fluid Cap 

60100 

+ 


125340 

Fluid Cap 

40100 

+ 


125328 

Fluid Cap 

60100 

+ 


125328 

Fluid Cap 

100150 

+ 


189351 


Press. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

1.3 3.9 30 2.1 7.4 40 3.0 6.1 52 3.9 9.4 60 5.3 10.2 78 

1.4 3.0 33 2.4 5.3 45 3.1 5.3 54 4.2 7.2 67 5.6 8.3 84 

1.5 2.3 35 2.5 4.4 47 3.2 4.5 57 4.6 5.3 73 6.0 6.6 89 

1.7 1.8 38 2.7 3.7 50 3.4 3.8 59 4.9 3.8 80 6.3 5.1 98 

1.8 1.3 41 2.8 3.1 52 3.5 3.2 62 – – – – – – 

2.0 .95 44 3.0 2.6 55 3.9 1.8 68 – – – – – – 

– – – 3.1 2.1 57 – – – – – – – – – 

1.0 17.0 23 2.0 24 44 2.4 28 51 3.4 38 72 3.9 65 75 

1.1 11.0 27 2.1 18.9 50 2.5 23 59 3.5 33 80 4.2 53 89 

1.3 7.6 33 2.2 14.4 56 2.7 18.9 66 3.7 28 89 4.6 40 108 

1.4 3.2 40 2.4 10.6 63 2.8 15.1 74 3.8 23 97 4.9 30 127 

– – – 2.5 7.2 71 3.0 11.7 79 3.9 19.7 105 5.3 21 149 

– – – – – – – – – 4.2 13.1 120 5.6 13.8 173 

– – – – – – – – – 4.6 7.2 138 6.3 3.2 225 

1.1 11.2 54 2.1 18.0 79 2.7 19.6 93 3.5 27 112 4.6 33 137 

1.3 8.5 60 2.2 15.8 84 2.8 17.3 98 3.7 25 116 4.9 28 149 

1.4 6.5 65 2.4 13.6 89 3.0 15.2 103 3.8 23 121 5.3 24 161 

1.5 5.0 71 2.5 11.6 95 3.1 13.2 109 3.9 21 126 5.6 19.7 174 

1.7 3.8 77 – – – 3.2 11.4 114 4.1 18.9 132 6.0 15.7 187 

– – – – – – – – – 4.2 17.0 137 6.3 12.4 200 

.85 27 33 1.8 38 55 2.4 39 67 3.2 58 76 4.6 59 106 

1.0 20 38 2.1 28 66 2.7 30 77 3.5 47 87 5.3 40 132 

1.1 15.9 45 2.2 24 71 3.0 24 87 3.8 38 97 5.6 32 145 

1.3 12.5 48 2.4 21 76 3.2 17.8 98 3.9 34 103 6.0 26 158 

1.4 10.2 56 2.5 17.8 82 3.4 15.1 103 4.2 27 113 6.3 20 172 

1.5 7.6 62 2.7 15.1 87 3.5 12.9 109 4.6 20 126 6.7 15.9 185 

– – – – – – 3.7 10.6 114 4.9 14.8 140 7.0 12.7 198 

1.0 29 90 1.8 56 117 2.1 100 119 3.0 126 140 4.1 140 181 

1.1 18.9 108 2.0 40 133 2.2 79 133 3.1 110 151 4.2 125 193 

– – – – – – 2.4 62 147 3.2 95 163 4.6 89 225 

– – – – – – 2.5 48 162 3.4 78 184 4.9 58 265 

– – – – – – 2.7 36 177 3.5 62 193 5.3 34 305 

– – – – – – – – – 3.7 48 210 5.6 16.7 340 

– – – – – – – – – 3.8 37 225 – – – 


1.5 

2.7 

3.2 

4.2 

5.6 

1.1 

2.1 

2.8 

3.7 

4.9 

1.4 

2.4 

3.0 

3.7 

5.3 

1.1 

2.4 

3.2 

3.9 

6.0 

1.0 

1.8 

2.4 

3.4 

4.9 

Liquid* 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 


Dimensions 

A 

(cm) 

25 

36 

58 

61 

64 

10 

10 

13 

15 

20 

15 

23 

25 

30 

33 

18 

23 

25 

30 

33 

18 

25 

25 

33 

36 

B 

(cm) 

33 

51 

74 

74 

76 

13 

13 

17 

20 

25 

18 

28 

33 

38 

41 

23 

30 

33 

38 

41 

20 

30 

30 

41 

43 

C 

(cm) 

46 

69 

91 

94 

97 

15 

17 

22 

28 

35 

20 

33 

46 

46 

48 

30 

41 

43 

48 

51 

25 

43 

46 

53 

58 

D 

(m) 

1.8 

2.0 

2.0 

2.1 

2.3 

2.4 

3.0 

3.4 

3.6 

4.0 

3.0 

3.2 

3.4 

3.5 

4.0 

3.4 

3.5 

3.7 

3.8 

4.4 

3.4 

3.8 

4.3 

4.6 

5.2 


Deflected Flat Spray 


Set-up 

No. 

SU240E 


Set-up 


Fluid and 



Fluid Cap 

28150 

+ 


189110-75° 


Press. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

.40 11.0 45 1.1 14.5 79 1.5 15.7 96 2.1 20 114 2.7 26 133 

.60 9.5 54 1.3 13.2 86 1.7 14.3 104 2.2 19.2 121 3.2 22 160 

.70 7.6 65 1.4 11.8 95 1.8 12.9 112 2.7 15.8 146 3.8 17.7 186 

.80 5.7 77 1.5 10.0 103 2.1 9.8 130 3.1 11.8 173 4.4 13.1 230 

– – – 1.7 8.7 113 2.2 8.3 142 3.2 10.3 183 4.6 10.2 250 


Deflected flat spray pattern 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F14

Pressure Spray Set-ups, External Mix, 



External mix air caps 

produce a flat spray pattern. 


• Atomization can be controlled by varying the air pressure without changing liquid flow rates with 

external mix set-ups. 

• For flat spray, dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle. 




• The liquid and compressed air or gas are mixed externally to produce a completely atomized spray. 

C 

B 

A 


Fluid cap 


Flat spray 

pattern 

D 

6" 

(15 cm) 

9" (23 cm) 

15" (38 cm) 


3612 

gasket 





Flat Spray (External Mix) 


Set-up 

No. 

SUE15B 


Set-up 


Fluid and 



Fluid Cap 

1650 

+ 


67228-45° 


Press. 




0.2 0.3 0.7 1.5 3 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

.20 2.8 25.2 3.5 3.5 26.3 .70 5.3 31.2 1.4 7.8 45.3 2.8 11.0 73.6 

.35 2.8 26.3 .70 3.5 31.2 1.05 5.3 39.6 1.75 7.8 53.8 3.5 11.0 85 

.70 2.8 31.2 1.05 3.5 39.6 1.4 5.3 45.3 2.1 7.8 59.5 4.2 11.0 102 

1.05 2.8 39.6 1.4 3.5 45.3 1.75 5.3 53.8 2.8 7.8 73.6 4.9 11.0 119 

1.4 2.8 45.3 1.75 3.5 53.8 2.1 5.3 59.4 3.5 7.8 85 5.3 11.0 127.5 

1.75 2.8 53.8 2.1 3.5 59.4 2.8 5.3 73.6 4.2 7.8 102 5.6 11.0 139 

2.1 2.8 59.4 2.8 3.5 73.6 3.5 5.3 85 5.6 7.8 139 6.3 11.0 159 



.20 

1.05 

1.4 

1.4 

1.75 

2.8 

4.9 

Liquid* 

.20 

.20 

.35 

1.4 

.70 

1.4 

2.8 


Dimensions 

A 

(cm) 

9.0 

9.0 

10.0 

11.5 

11.5 

13.0 

15.0 

B 

(cm) 

15.0 

15.0 

15.0 

18.0 

15.0 

18.0 

18.0 

C 

(cm) 

23 

23 

23 

25 

24 

28 

24 

D 

(m) 

.90 

1.2 

1.2 

1.5 

1.5 

1.8 

2.4 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F15







Set-up 

No. 

SUE18B 


Set-up 


Fluid and 



Fluid Cap 

1650 

+ 


62240-60° 


Press. 




0.2 0.3 0.7 1.5 3 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.35 2.8 22 .35 3.5 22 .40 5.3 25 .60 7.8 28 .70 11.0 34 

.40 2.8 25 .40 3.5 25 .60 5.3 28 .70 7.8 34 1.1 11.0 45 

.50 2.8 27.5 .60 3.5 28 .70 5.3 34 1.1 7.8 45 1.8 11.0 62 

.60 2.8 28 .70 3.5 34 .85 5.3 40 1.4 7.8 54 2.5 11.0 79 

.35 4.5 26.3 .70 5.5 31.2 1.05 8.3 39.6 1.75 12.2 53.8 3.15 16.6 82 

l/h 


l/min 


.40 

.60 

.60 

1.1 

1.4 

1.1 

1.4 

.35 

Liquid* 

.30 

.70 

1.5 

1.5 

1.5 

2.0 

3.0 

.20 


Dimensions 

A 

(cm) 

20 

23 

28 

28 

25 

28 

30 

7.5 

B 

(cm) 

28 

30 

35 

33 

30 

35 

38 

14.0 

C 

(cm) 

33 

40 

46 

43 

41 

48 

51 

22 

D 

(m) 

1.2 

1.8 

1.8 

2.4 

2.7 

2.6 

2.7 

1.0 

.70 4.5 31.2 1.05 5.5 39.6 1.4 8.3 45.3 2.1 12.2 59.4 3.5 16.6 85 

1.4 

.20 

9.0 

15.0 

22 

1.7 

SUE15A 

Fluid Cap 

2050 

+ 


67228-45° 

1.05 4.5 39.6 1.4 5.5 45.3 1.75 8.3 53.8 2.8 12.2 73.6 4.2 16.6 102 

1.4 4.5 45.3 1.75 5.5 53.8 2.1 8.3 59.4 3.5 12.2 85 4.9 16.6 119 

1.75 4.5 53.8 2.1 5.5 59.4 2.8 8.3 73.6 4.2 12.2 102 5.25 16.6 127 

1.75 

1.75 

2.1 

.35 

1.4 

.70 

10.0 

13.0 

13.0 

16.5 

19.0 

18.0 

23 

29 

25 

1.8 

2.1 

1.8 

2.1 4.5 59.4 2.8 5.5 73.6 3.5 8.3 85 4.9 12.2 119 6.3 16.6 159 

3.5 

1.4 

13.0 

22 

30 

2.4 

SUE18A 

Fluid Cap 

2050 

+ 


62240-60° 

2.8 4.5 73.6 3.5 5.5 85 4.2 8.3 102 6.3 12.2 159 6.7 16.6 164 

.35 4.5 22 .35 5.5 22 .60 8.3 28 .70 12.2 34 1.1 16.6 45 

.60 4.5 28 .70 5.5 34 .70 8.3 34 1.4 12.2 54 1.4 16.6 54 

.70 4.5 34 1.1 5.5 45 1.4 8.3 54 2.1 12.2 71 2.1 16.6 71 

1.1 4.5 45 1.4 5.5 54 2.1 8.3 71 2.5 12.2 79 2.5 16.6 79 

.70 8.5 31.2 1.05 10.4 39.6 1.4 15.9 45.3 2.5 23 68 3.5 33 85 

5.3 

.70 

1.1 

.70 

1.4 

2.5 

1.8 

1.8 

.70 

2.8 

.30 

.70 

1.5 

1.5 

1.5 

2.0 

3.0 

.20 

15.0 

28 

30 

38 

35 

33 

38 

41 

13.0 

19.0 

33 

38 

46 

43 

40 

46 

48 

16.5 

25 

40 

48 

58 

56 

51 

58 

66 

25 

3.0 

1.5 

2.1 

1.8 

2.4 

3.0 

2.7 

2.9 

1.2 

1.05 8.5 39.6 1.4 10.4 45.3 1.75 15.9 53.8 2.8 23 73.6 4.2 33 102 

1.75 

.20 

13.0 

16.5 

25 

1.8 

SUE15 

Fluid Cap 

2850 

+ 


67228-45° 

1.4 8.5 45.3 1.75 10.4 53.8 2.1 15.9 59.4 3.5 23 85 4.9 33 119 

1.75 8.5 53.8 2.1 10.4 59.4 2.8 15.9 73.6 4.2 23 102 5.3 33 127 

2.1 8.5 59.4 2.8 10.4 73.6 3.5 15.9 85.0 4.9 23 119 5.6 33 139 

2.1 

2.5 

2.8 

.35 

1.4 

.70 

13.0 

14.0 

14.0 

18.0 

20 

19.0 

24 

32 

30 

1.8 

1.8 

2.3 

2.8 8.5 73.6 3.5 10.4 85 4.2 15.9 102 5.6 23 139 6.3 33 159 

4.2 

1.4 

14.0 

20 

36 

3.0 

SUE18 

Fluid Cap 

2850 

+ 


62240-60° 

3.5 8.5 85 4.2 10.4 102 4.9 15.9 119 6.3 23 159 7.0 33 176 

.40 8.5 25 .40 10.4 25 .40 15.9 25 .70 23 34 1.4 33 54 

.50 8.5 27.5 .60 10.4 28 .60 15.9 28 .85 23 40 1.8 33 62 

.60 8.5 28 .65 10.4 31 .70 15.9 34 1.1 23 45 2.1 33 71 

.70 8.5 34 .70 10.4 34 .85 15.9 40 1.4 23 54 2.5 33 79 

5.3 

.60 

.60 

.70 

1.1 

1.4 

1.8 

2.1 

2.8 

.30 

.70 

1.5 

1.5 

1.5 

2.0 

3.0 

16.5 

35 

35 

38 

41 

43 

41 

41 

20 

48 

48 

48 

51 

53 

51 

51 

30 

61 

63 

63 

66 

66 

69 

69 

4.0 

1.8 

1.5 

1.8 

2.1 

2.4 

2.7 

2.9 


Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F16







Set-up 

No. 


Set-up 


Fluid and 




Press. 



0.2 0.3 0.7 1.5 3 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Liquid* 


Dimensions 

A 

(cm) 

B 

(cm) 

C 

(cm) 

D 

(m) 

.70 13.4 85 1.0 16.4 102 1.4 25 116 2.5 37 178 3.2 52 212 

.70 

.20 

13.0 

19.0 

25 

1.7 

1.0 13.4 102 1.4 16.4 116 1.8 25 139 2.8 37 195 3.5 52 232 

1.8 

.20 

13.0 

19.0 

25 

2.7 

SUE25B 

Fluid Cap 

35100 

+ 


134255-45° 

1.4 13.4 116 1.8 16.4 139 2.1 25 156 3.5 37 227 3.9 52 255 

1.8 13.4 139 2.1 16.4 156 2.5 25 178 4.2 37 266 4.2 52 275 

2.1 13.4 156 2.8 16.4 195 2.8 25 195 4.9 37 312 4.9 52 314 

2.1 

2.5 

2.5 

.35 

.70 

1.4 

15.0 

15.0 

16.5 

19.0 

22 

23 

28 

28 

36 

3.0 

3.5 

3.7 

2.8 13.4 195 3.5 16.4 227 3.5 25 227 5.6 37 360 5.6 52 360 

4.2 

1.4 

16.5 

23 

37 

4.3 

3.5 13.4 227 4.2 16.4 266 4.2 25 266 6.3 37 411 6.3 52 411 

4.9 

2.8 

16.5 

22 

32 

4.9 

SUE28B 

Fluid Cap 

35100 

+ 


122281-60° 

.60 13.4 91 .70 16.4 102 1.4 25 156 2.1 37 210 3.2 52 285 

.70 13.4 102 1.1 16.4 130 2.1 25 210 2.8 37 260 4.2 52 360 

1.1 13.4 130 1.8 16.4 184 2.5 25 235 3.5 37 310 5.3 52 430 

1.4 13.4 156 2.1 16.4 210 2.8 25 260 4.2 37 360 5.6 52 455 

1.4 

2.1 

2.1 

3.2 

4.2 

3.9 

4.2 

.30 

.70 

1.5 

1.5 

1.5 

2.0 

3.0 

33 

33 

35 

38 

38 

41 

38 

38 

40 

46 

48 

48 

51 

51 

48 

56 

58 

66 

64 

69 

71 

3.8 

4.3 

4.0 

4.6 

5.2 

4.6 

4.9 



.70 17.6 85 1.4 22 116 1.8 33 139 2.8 48 195 3.5 68 232 

.70 

.35 

15.0 

19.0 

27 

2.1 

1.0 17.6 102 1.8 22 139 2.1 33 156 3.2 48 212 4.2 68 275 

1.8 

.70 

15.0 

19.0 

27 

3.0 

SUE25A 

Fluid Cap 

40100 

+ 


134255-45° 

1.4 17.6 116 2.1 22 156 2.5 33 178 3.5 48 227 4.9 68 314 

1.8 17.6 139 2.5 22 178 2.8 33 195 4.2 48 266 5.3 68 340 

2.1 17.6 156 2.8 22 195 3.5 33 227 4.9 48 312 5.6 68 360 

2.5 

2.8 

2.8 

1.4 

1.4 

1.4 

15.0 

15.0 

16.5 

22 

22 

25 

33 

36 

37 

3.4 

3.8 

4.0 

2.8 17.6 195 3.5 22 227 4.2 33 266 5.6 48 360 6.3 68 411 

4.2 

2.1 

16.5 

25 

37 

4.9 

3.5 17.6 227 4.2 22 266 4.9 33 312 6.3 48 411 6.6 68 428 

5.3 

2.8 

18.0 

23 

36 

5.8 

SUE28A 

SUE28 

Fluid Cap 

40100 

+ 


122281-60° 

Fluid Cap 

60100 

+ 


122281-60° 

.60 17.6 91 .70 22 102 1.1 33 130 2.5 48 235 3.5 68 310 

1.1 17.6 130 1.4 22 156 1.8 33 184 3.2 48 285 4.6 68 380 

1.4 17.6 156 1.8 22 184 2.5 33 235 3.9 48 330 6.0 68 475 

1.8 17.6 184 2.1 22 210 2.8 33 260 4.2 48 360 6.7 68 525 

.70 36 102 1.1 45 130 1.8 68 184 3.2 100 285 5.3 141 430 

1.1 36 130 1.4 45 156 2.1 68 210 3.5 100 310 6.0 141 475 

1.4 36 156 2.1 45 210 2.8 68 260 4.9 100 405 6.7 141 525 

1.8 36 184 2.5 45 235 3.2 68 285 5.9 100 455 7.0 141 550 

1.1 

1.8 

2.5 

3.2 

4.2 

4.2 

4.9 

2.1 

2.8 

3.2 

4.6 

5.6 

3.9 

6.3 

.20 

.70 

1.5 

1.5 

1.5 

2.0 

3.0 

.30 

.70 

1.5 

1.5 

1.5 

2.0 

3.0 

33 

35 

38 

33 

30 

33 

33 

40 

46 

48 

43 

38 

48 

41 

38 

48 

46 

43 

43 

43 

43 

56 

58 

58 

53 

51 

64 

56 

51 

64 

64 

61 

58 

61 

61 

76 

81 

79 

76 

66 

84 

79 

3.5 

3.0 

3.8 

4.3 

4.9 

5.2 

4.0 

3.0 

4.0 

4.3 

4.9 

5.8 

4.3 

5.8 


Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F17







Set-up 

No. 

SUE25 


Set-up 


Fluid and 



Fluid Cap 

60100 

+ 


134255-45° 


Press. 




0.2 0.3 0.7 1.5 3 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

1.0 36 102 1.8 45 139 2.5 68 178 3.2 100 212 3.9 141 255 

1.4 36 116 2.1 45 156 2.8 68 195 3.5 100 227 4.2 141 275 

1.8 36 139 2.5 45 178 3.2 68 212 3.9 100 246 4.6 141 297 

2.1 36 156 2.8 45 195 3.5 68 227 4.2 100 266 4.9 141 314 

2.5 36 178 3.2 45 212 4.2 68 266 4.9 100 312 5.6 141 360 

2.8 36 195 3.5 45 227 4.9 68 312 5.6 100 360 6.3 141 411 

3.5 36 227 4.2 45 266 5.6 68 360 6.3 100 411 7.0 141 453 


1.0 

2.1 

2.8 

3.2 

3.5 

4.2 

5.6 

Liquid* 

.20 

.20 

.35 

1.4 

.70 

1.4 

2.8 


Dimensions 

A 

(cm) 

15.0 

15.0 

18.0 

20 

19.0 

20 

18.0 

B 

(cm) 

20 

22 

24 

28 

27 

28 

24 

C 

(cm) 

25 

29 

36 

39 

38 

39 

38 

D 

(m) 

2.7 

3.0 

3.5 

3.7 

4.0 

4.3 

5.9 

SUE45B 

Fluid Cap 

60150 

+ 


200278-45° 

1.8 36 235 1.8 45 235 2.5 68 300 3.9 100 410 – – – 

2.1 36 260 2.1 45 260 2.8 68 330 4.2 100 445 – – – 

2.5 36 300 2.5 45 300 3.2 68 355 4.6 100 480 – – – 

2.8 36 330 2.8 45 330 3.5 68 380 4.9 100 529 – – – 

3.2 36 355 3.2 45 355 3.9 68 410 5.3 100 565 – – – 

3.5 36 380 3.5 45 380 4.2 68 445 5.6 100 600 – – – 

4.2 36 445 4.2 45 445 4.9 68 520 6.3 100 685 – – – 

1.8 

2.8 

2.8 

3.5 

3.9 

4.2 

4.9 

.20 

.20 

.30 

.70 

1.5 

1.0 

1.5 

15.0 

15.0 

15.0 

17.0 

17.0 

17.0 

17.0 

20 

20 

20 

22 

22 

23 

23 

29 

30 

30 

32 

34 

33 

34 

3.0 

3.4 

4.0 

4.3 

4.6 

4.7 

5.5 

SUE45A 

Fluid Cap 

80150 

+ 


200278-45° 

2.1 64 260 2.8 78 330 3.9 119 410 4.9 175 520 – – – 

2.5 64 300 3.2 78 355 4.2 119 445 5.3 175 565 – – – 

2.8 64 330 3.5 78 380 4.6 119 480 5.6 175 600 – – – 

3.2 64 355 3.9 78 410 4.9 119 520 6.0 175 640 – – – 

3.5 64 380 4.2 78 445 5.3 119 565 6.3 175 685 – – – 

4.2 64 445 4.9 78 520 5.6 119 600 – – – – – – 

4.9 64 520 5.6 78 600 6.3 119 685 – – – – – – 

2.1 

3.2 

3.9 

4.9 

4.9 

5.3 

5.6 

.20 

.20 

.30 

.70 

1.5 

1.0 

1.5 

17.0 

18.0 

18.0 

18.0 

20 

18.0 

20 

24 

24 

25 

25 

25 

25 

25 

34 

36 

36 

36 

38 

38 

38 

3.5 

4.3 

4.9 

5.5 

5.5 

5.8 

6.1 

SUE45 

Fluid Cap 

100150 

+ 


200278-45° 

2.8 102 330 3.5 125 380 4.6 192 480 5.6 280 600 – – – 

3.2 102 355 3.9 125 410 4.9 192 520 6.0 280 640 – – – 

3.5 102 380 4.2 125 445 5.3 192 565 6.3 280 685 – – – 

3.9 102 410 4.6 125 480 5.6 192 600 – – – – – – 

4.2 102 445 4.9 125 520 6.0 192 640 – – – – – – 

4.6 102 480 5.3 125 565 6.3 192 685 – – – – – – 

4.9 102 520 5.6 125 600 – – – – – – – – – 

2.8 

3.9 

4.6 

5.3 

5.6 

5.6 

6.0 

.20 

.20 

.30 

.70 

1.0 

1.5 

1.5 

19.0 

20 

20 

22 

22 

22 

22 

25 

25 

25 

27 

27 

27 

27 

36 

37 

37 

38 

41 

41 

41 

4.6 

4.9 

5.2 

5.5 

5.5 

5.8 

6.1 


Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F18


High Transfer Efficiency (HTE), 1/4J Series 


C 

B 

A 

• A new air cap design enables the use of lower air pressures to achieve 

the same spray performance as conventional external mix set-ups. 

Flat spray 

pattern 

• HTE set-ups operate at pressures as low as 5 psi (0.3 bar). 

• A large air chamber directly feeds the air exit orifices. Design provides 

high liquid transfer efficiency, minimal air loss, and minimal misting. 

• Air consumption is reduced and maximum spray coverage on the target 

is achieved. 

• See also 

– Section G, Automatic Spray Nozzles 

Air Ca p s 

D 

Round spray 

pattern 

D 

C 

B 

A 

6" (15 cm) 

9" (23 cm) 

15" (38 cm) 

6" (15 cm) 

9" (23 cm) 

15" (38 cm) 

1158 retainer ring and 3612 gasket must be ordered separately 

from the spray set-up, but are included in the standard nozzle 

assembly. Please contact your sales engineer. 

HTE air cap produces a flat 

spray and a round spray. 






Set-up 

No. 

SU-HTE60D 

SU-HTE60E 

SU-HTE60F 


Set-up 


Fluid and 



Fluid Cap 

PF28100 

+ 


LP130262-60 

Fluid Cap 

PF20100 

+ 


LP130262-60 

Fluid Cap 

PF16100 

+ 


LP130262-60 


Press. 




0.3 0.7 1 1.4 2.1 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

.55 11.4 94 .55 15.9 94 – – – – – – – – – 

.69 11.4 106 .69 15.9 106 .69 19.3 106 – – – – – – 

.83 11.4 118 .83 15.9 118 .83 19.3 118 .83 23 118 – – – 

.97 11.4 129 .97 15.9 129 .97 19.3 129 .97 23 129 .97 27 129 

1.1 11.4 139 1.1 15.9 139 1.1 19.3 139 1.1 23 139 1.1 27 139 

.41 6.1 81 .41 8.3 81 – – – – – – – – – 

.55 6.1 94 .55 8.3 94 .55 9.8 94 – – – – – – 

.69 6.1 106 .69 8.3 106 .69 9.8 106 .69 11.7 106 – – – 

.83 6.1 118 .83 8.3 118 .83 9.8 118 .83 11.7 118 – – – 

.97 6.1 129 .97 8.3 129 .97 9.8 129 .97 11.7 129 .97 14.0 129 

1.1 6.1 139 1.1 8.3 139 1.1 9.8 139 1.1 11.7 139 1.1 14.0 139 

.28 3.8 65 – – – – – – – – – – – – 

.41 3.8 81 – – – – – – – – – – – – 

.55 3.8 94 .55 5.3 94 .55 6.4 94 .55 7.6 94 – – – 

.69 3.8 106 .69 5.3 106 .69 6.4 106 .69 7.6 106 – – – 

.83 3.8 118 .83 5.3 118 .83 6.4 118 .83 7.6 118 .83 9.1 118 

.97 3.8 129 .97 5.3 129 .97 6.4 129 .97 7.6 129 .97 9.1 129 

1.1 3.8 139 1.1 5.3 139 1.1 6.4 139 1.1 7.6 139 1.1 9.1 139 

Add DF to part number for “Drip Free” set-ups. Example: SU-HTE60D-DF. 

The operating pressures and flow rates are based on spraying water and air at room temperature. 

Adjustments may need to be made to accommodate other liquids with different characteristics. 


.69 

1.0 

.69 

1.0 

.69 

.34 

.69 

1.0 

.34 

.69 

1.0 

.21 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.34 

.69 

.69 

1.4 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.34 

.69 

.69 

.69 


Dimensions 

A 

(cm) 

18 

13 

29 

15 

25 

18 

10 

8 

20 

17 

17 

24 

23 

20 

17 

22 

19 

15 

B 

(cm) 

33 

15 

34 

23 

38 

23 

11 

11 

28 

18 

18 

28 

25 

23 

19 

24 

23 

19 

C 

(cm) 

36 

20 

36 

25 

43 

16 

11 

14 

33 

18 

19 

33 

30 

29 

22 

30 

28 

24 

D 

(cm) 

91 

102 

102 

114 

104 

64 

79 

86 

56 

69 

81 

58 

61 

64 

71 

56 

64 

74 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F19







Set-up 

No. 

SU-HTE61C 

SU-HTE61D 

SU-HTE61E 

SU-HTE61F 

SU-HTE62D 

SU-HTE62E 


Set-up 


Fluid and 



Fluid Cap 

PF35100 

+ 


LP130285-60 

Fluid Cap 

PF28100 

+ 


LP130285-60 

Fluid Cap 

PF20100 

+ 


LP130285-60 

Fluid Cap 

PF16100 

+ 


LP130285-60 

Fluid Cap 

PF28100 

+ 


LP120262-90 

Fluid Cap 

PF20100 

+ 


LP120262-90 


Press. 







0.3 0.7 1 1.4 2.1 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.41 17.8 100 – – – – – – – – – – – – 

.55 17.8 117 .55 25 117 – – – – – – – – – 

.69 17.8 133 .69 25 133 – – – – – – – – – 

.83 17.8 149 .83 25 149 .83 31 149 – – – – – – 

l/h 


l/min 

.97 17.8 163 .97 25 163 .97 31 163 .97 36 163 .97 43 163 

1.1 17.8 177 1.1 25 177 1.1 31 177 1.1 36 177 1.1 43 177 

.41 11.4 100 – – – – – – – – – – – – 

.55 11.4 117 .55 15.9 117 – – – – – – – – – 

.69 11.4 133 .69 15.9 133 .69 19.3 133 – – – – – – 

.83 11.4 149 .83 15.9 149 .83 19.3 149 – – – – – – 

.97 11.4 163 .97 15.9 163 .97 19.3 163 .97 23 163 .97 27 163 

1.1 11.4 177 1.1 15.9 177 1.1 19.3 177 1.1 23 177 1.1 27 177 

.28 6.1 80 – – – – – – – – – – – – 

.41 6.1 100 – – – – – – – – – – – – 

.55 6.1 117 .55 8.3 117 – – – – – – – – – 

.69 6.1 133 .69 8.3 133 .69 9.8 133 .69 11.7 133 .69 14.0 133 

.83 6.1 149 .83 8.3 149 .83 9.8 149 .83 11.7 149 .83 14.0 149 

.97 6.1 163 .97 8.3 163 .97 9.8 163 .97 11.7 163 .97 14.0 163 

1.1 6.1 177 1.1 8.3 177 1.1 9.8 177 1.1 11.7 177 1.1 14.0 177 

.28 3.8 80 – – – – – – – – – – – – 

.41 3.8 100 .41 5.3 100 – – – – – – – – – 

.55 3.8 117 .55 5.3 117 .55 6.4 117 .55 7.6 117 – – – 

.69 3.8 133 .69 5.3 133 .69 6.4 133 .69 7.6 133 .69 9.1 133 

.83 3.8 149 .83 5.3 149 .83 6.4 149 .83 7.6 149 .83 9.1 149 

.97 3.8 163 .97 5.3 163 .97 6.4 163 .97 7.6 163 .97 9.1 163 

1.1 3.8 177 1.1 5.3 177 1.1 6.4 177 1.1 7.6 177 1.1 9.1 177 

.28 11.4 57 – – – – – – – – – – – – 

.41 11.4 70 .41 15.9 70 – – – – – – – – – 

.55 11.4 82 .55 15.9 82 .55 19.3 82 – – – – – – 

.69 11.4 93 .69 15.9 93 .69 19.3 93 .69 23 93 – – – 

.83 11.4 103 .83 15.9 103 .83 19.3 103 .83 23 103 .83 27 103 

.97 11.4 112 .97 15.9 112 .97 19.3 112 .97 23 112 .97 27 112 

1.1 11.4 121 1.1 15.9 121 1.1 19.3 121 1.1 23 121 1.1 27 121 

.28 6.1 57 – – – – – – – – – – – – 

.41 6.1 70 – – – – – – – – – – – – 

.55 6.1 82 .55 8.3 82 – – – – – – – – – 

.69 6.1 93 .69 8.3 93 .69 9.8 93 .69 11.7 93 – – – 

.83 6.1 103 .83 8.3 103 .83 9.8 103 .83 11.7 103 .83 14.0 103 

.97 6.1 112 .97 8.3 112 .97 9.8 112 .97 11.7 112 .97 14.0 112 

1.1 6.1 121 1.1 8.3 121 1.1 9.8 121 1.1 11.7 121 1.1 14.0 121 


.34 

.69 

1.0 

.69 

1.0 

.69 

.34 

.69 

1.0 

1.0 

.34 

.69 

.21 

.34 

.69 

1.0 

1.0 

.34 

.69 

.21 

.34 

.69 

1.0 

1.0 

.34 

.69 

.21 

.34 

.69 

1.0 

.34 

.69 

1.0 

.21 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.34 

.34 

.69 

.69 

1.4 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.34 

.69 

.69 

.69 


Dimensions 

A 

(cm) 

27 

23 

17 

27 

23 

31 

18 

13 

10 

13 

23 

15 

20 

18 

9 

9 

15 

24 

18 

25 

22 

18 

19 

22 

28 

22 

18 

28 

28 

18 

25 

36 

41 

25 

19 

18 

15 

19 

17 

17 

B 

(cm) 

36 

29 

23 

36 

28 

41 

19 

15 

13 

15 

28 

22 

25 

19 

13 

10 

19 

25 

20 

32 

25 

24 

25 

25 

32 

27 

28 

32 

33 

18 

32 

38 

41 

34 

24 

20 

17 

28 

23 

20 

C 

(cm) 

51 

31 

31 

42 

33 

52 

20 

19 

17 

20 

30 

23 

36 

23 

15 

14 

24 

29 

23 

37 

30 

30 

28 

29 

38 

29 

41 

36 

34 

20 

33 

43 

46 

38 

25 

22 

18 

30 

25 

22 

D 

(cm) 

69 

94 

109 

94 

109 

89 

74 

91 

145 

109 

84 

94 

46 

61 

74 

76 

99 

69 

69 

74 

84 

86 

84 

84 

81 

84 

86 

96 

107 

114 

84 

102 

127 

53 

71 

84 

99 

66 

74 

94 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F20






Set-up 

No. 

SU-HTE62F 

SU-HTE64C 

SU-HTE64D 

SU-HTE64E 

SU-HTE64F 


Set-up 


Fluid and 



Fluid Cap 

PF16100 

+ 


LP120262-90 

Fluid Cap 

PF35100 

+ 


LP1302100- 

60 

Fluid Cap 

PF28100 

+ 


LP1302100- 

60 

Fluid Cap 

PF20100 

+ 


LP1302100- 

60 

Fluid Cap 

PF16100 

+ 


LP1302100- 

60 


Press. 




0.3 0.7 1 1.4 2.1 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.28 3.8 57 – – – – – – – – – – – – 

.41 3.8 70 .41 5.3 70 – – – – – – – – – 

.55 3.8 82 .55 5.3 82 .55 6.4 82 .55 7.6 82 – – – 

.69 3.8 93 .69 5.3 93 .69 6.4 93 .69 7.6 93 .69 9.1 93 

l/h 


l/min 

.83 3.8 103 .83 5.3 103 .83 6.4 103 .83 7.6 103 .83 9.1 103 

.97 3.8 112 .97 5.3 112 .97 6.4 112 .97 7.6 112 .97 9.1 112 

1.1 3.8 121 1.1 5.3 121 1.1 6.4 121 1.1 7.6 121 1.1 9.1 121 

.41 17.8 112 – – – – – – – – – – – – 

.55 17.8 132 .55 25 132 – – – – – – – – – 

.69 17.8 151 .69 25 151 – – – – – – – – – 

.83 17.8 168 .83 25 168 .83 31 168 – – – – – – 

.97 17.8 185 .97 25 185 .97 31 185 .97 36 185 .97 43 185 

1.1 17.8 201 1.1 25 201 1.1 31 201 1.1 36 201 1.1 43 201 

.41 11.4 112 – – – – – – – – – – – – 

.55 11.4 132 .55 15.9 132 – – – – – – – – – 

.69 11.4 151 .69 15.9 151 .69 19.3 151 – – – – – – 

.83 11.4 168 .83 15.9 168 .83 19.3 168 – – – – – – 

.97 11.4 185 .97 15.9 185 .97 19.3 185 .97 23 185 – – – 

1.1 11.4 201 1.1 15.9 201 1.1 19.3 201 1.1 23 201 1.1 27 201 

.28 6.1 90 – – – – – – – – – – – – 

.41 6.1 112 – – – – – – – – – – – – 

.55 6.1 132 .55 8.3 132 – – – – – – – – – 

.69 6.1 151 .69 8.3 151 .69 9.8 151 .69 11.7 151 .69 14.0 151 

.83 6.1 168 .83 8.3 168 .83 9.8 168 .83 11.7 168 .83 14.0 168 

.97 6.1 185 .97 8.3 185 .97 9.8 185 .97 11.7 185 .97 14.0 185 

1.1 6.1 201 1.1 8.3 201 1.1 9.8 201 1.1 11.7 201 1.1 14.0 201 

.28 3.8 90 – – – – – – – – – – – – 

.41 3.8 112 .41 5.3 112 – – – – – – – – – 

.55 3.8 132 .55 5.3 132 .55 6.4 132 .55 7.6 132 – – – 

.69 3.8 151 .69 5.3 151 .69 6.4 151 .69 7.6 151 .69 9.1 151 

.83 3.8 168 .83 5.3 168 .83 6.4 168 .83 7.6 168 .83 9.1 168 

.97 3.8 185 .97 5.3 185 .97 6.4 185 .97 7.6 185 .97 9.1 185 

1.1 3.8 201 1.1 5.3 201 1.1 6.4 201 1.1 7.6 201 1.1 9.1 201 





.21 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.69 

1.0 

.21 

.34 

.69 

1.0 

.34 

.69 

1.0 

.21 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.34 

.69 

.69 

.69 


Dimensions 

A 

(cm) 

23 

22 

15 

17 

23 

20 

19 

30 

28 

15 

36 

30 

20 

28 

20 

18 

28 

20 

18 

18 

17 

13 

13 

19 

14 

14 

23 

18 

17 

14 

23 

19 

14 

B 

(cm) 

28 

24 

19 

19 

28 

23 

23 

41 

29 

23 

41 

41 

30 

33 

25 

20 

30 

28 

20 

23 

17 

13 

13 

22 

17 

17 

28 

23 

20 

18 

28 

23 

18 

C 

(cm) 

32 

27 

22 

23 

32 

30 

28 

48 

38 

25 

48 

46 

33 

36 

33 

28 

46 

36 

33 

28 

22 

15 

14 

23 

19 

18 

34 

29 

25 

22 

34 

25 

22 

D 

(cm) 

66 

71 

61 

64 

66 

66 

66 

76 

86 

112 

74 

89 

104 

99 

102 

127 

76 

104 

135 

58 

64 

84 

99 

74 

89 

109 

69 

69 

76 

76 

71 

74 

74 



Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F21





Round Spray (External Mix) 


Set-up 

No. 

SU-HTE91A 

SU-HTE91B 

SU-HTE91C 


Set-up 


Fluid and 



Fluid Cap 

PF2850 

+ 


LP60650-60 

Fluid Cap 

PF2050 

+ 


LP60650-60 

Fluid Cap 

PF1650 

+ 


LP60650-60 


Press. 




0.3 0.7 1 1.4 2.1 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

.28 11.4 54 – – – – – – – – – – – – 

.41 11.4 71 .41 15.9 71 – – – – – – – – – 

.55 11.4 82 .55 15.9 82 .55 19.3 82 .55 23 82 .55 27 82 

.69 11.4 96 .69 15.9 96 .69 19.3 96 .69 23 96 .69 27 96 

.83 11.4 108 .83 15.9 108 .83 19.3 108 .83 23 108 .83 27 108 

.97 11.4 116 .97 15.9 116 .97 19.3 116 .97 23 116 .97 27 116 

1.1 11.4 127 1.1 15.9 127 1.1 19.3 127 1.1 23 127 1.1 27 127 

.28 6.1 54 – – – – – – – – – – – – 

.41 6.1 71 – – – – – – – – – – – – 

.55 6.1 82 .55 8.3 82 – – – – – – – – – 

.69 6.1 96 .69 8.3 96 .69 9.8 96 .69 11.7 96 – – – 

.83 6.1 108 .83 8.3 108 .83 9.8 108 .83 11.7 108 – – – 

.97 6.1 116 .97 8.3 116 .97 9.8 116 .97 11.7 116 .97 14.0 116 

1.1 6.1 127 1.1 8.3 127 1.1 9.8 127 1.1 11.7 127 1.1 14.0 127 

.41 3.8 71 – – – – – – – – – – – – 

.55 3.8 82 .55 5.3 82 – – – – – – – – – 

.69 3.8 96 .69 5.3 96 – – – – – – – – – 

.83 3.8 108 .83 5.3 108 – – – – – – – – – 

.97 3.8 116 .97 5.3 116 .97 6.4 116 .97 7.6 116 – – – 

1.1 3.8 127 1.1 5.3 127 1.1 6.4 127 1.1 7.6 127 – – – 





.21 

.34 

.69 

1.0 

.34 

.69 

1.0 

.21 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.69 

1.0 

.34 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.34 

.69 

.69 

.69 

.34 

.34 

.34 

.69 

.69 

.69 


Dimensions 

A 

(cm) 

3 

9 

5 

5 

6 

4 

3 

5 

6 

5 

5 

6 

5 

5 

9 

10 

10 

5 

8 

8 

B 

(cm) 

8 

9 

9 

9 

11 

6 

6 

9 

8 

9 

8 

8 

9 

8 

10 

11 

13 

10 

10 

9 

C 

(cm) 

9 

13 

10 

13 

14 

9 

10 

11 

9 

13 

13 

9 

13 

13 

13 

14 

15 

11 

11 

13 

D 

(cm) 

112 

102 

109 

112 

99 

104 

119 

104 

107 

107 

124 

107 

107 

124 

86 

97 

117 

89 

97 

132 

Ordering Info 

Nozzle Body* 



1/4 J – SS + SU-HTE60D – SS 

l l l l l 

Inlet 


Nozzle 

No. 

Material 



Set-up Number 

Material 




HTE60D – SS 

l 

l 


Set-up Number 

Material 


BSPT connections require the addition of a “B” prior to the nozzle body inlet connection. 

*To order fluid cap only, use fluid cap number (shown in performance data charts and material code). 

To order air cap only, use air cap number (shown in performance data charts and material code). 

To order spray nozzle without set-up, use inlet connection, nozzle body and material code. 

To order Drip Free set-ups, add DF after set-up number: SU-HTE60D-DF – SS. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F22

Siphon/Gravity-Fed Spray Set-ups, 

External Mix, 1/8J and 1/4J Series 


Round spray and flat spray 

air caps produce round spray 

and flat spray patterns. 


• For round and flat sprays, angle “A” is maintained throughout distance “B”. Beyond “B”, the spray 


• When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid siphon or a 

gravity-feed. 

• Designed to draw liquid through the feed line into the air flow where it is atomized. 

Round spray 

pattern 

A 

D 

B 

1158 retainer ring and 3612 gasket must be ordered separately from the spray set-up, but are 

included in the standard nozzle assembly. Please contact your sales engineer. 

Refer to page F3 for Siphon/Gravity-Fed Spray Set-ups diagram. 







Set-up 

No. 


Set-up 


Fluid and 




Press. 

Atomizing 



Capacity 

l/min 

Gravity Head (cm) 

Liquid Capacity 

(liters per hour)* 

Siphon Height (cm) 

45 30 15 10 20 30 60 90 


Spray Dimensions 

at 20 cm Siphon Height 

A 

(cm) 

B 

(cm) 

C 

(cm) 

D 

(m) 

SUF1 

Fluid Cap 2850 

+ 

Air Cap 73420 

.70 28 1.3 1.2 1.1 1.0 .95 .83 .64 .49 

1.5 43 1.2 1.1 1.0 .90 .86 .78 .66 .54 

2.0 50 .82 .76 .68 .57 .50 – – – 

.70 

1.5 

2.0 

20 

21 

23 

26 

29 

30 

38 

38 

38 

2.1 

2.1 

1.8 

SUF2C 


+ 


1.5 56 3.7 3.5 3.3 2.9 2.8 2.5 2.3 2.1 

2.0 65 3.4 3.3 3.1 2.8 2.7 2.6 2.4 2.2 

3.0 87 2.8 2.7 2.5 2.4 2.2 2.1 1.9 1.7 

4.0 110 1.9 1.8 1.6 1.5 1.3 1.2 – – 

1.5 

2.0 

3.0 

4.0 

23 

24 

27 

28 

32 

34 

37 

39 

38 

42 

46 

48 

2.7 

2.7 

3.0 

2.7 

SUF3B 


+ 


1.5 68 5.1 4.8 4.5 3.8 3.7 3.5 3.0 2.4 

2.0 78 4.9 4.7 4.4 3.6 3.4 3.2 2.9 2.3 

3.0 103 3.4 3.2 3.0 2.2 2.0 1.7 – – 

3.5 117 2.2 2.0 1.7 – – – – – 

1.5 

2.0 

3.0 

19 

20 

22 

23 

25 

27 

27 

28 

30 

3.4 

3.4 

3.0 

SUF4B 


+ 


1.5 63 7.6 7.2 6.6 5.7 5.4 5.1 4.6 3.7 

2.0 73 7.6 7.3 6.8 5.9 5.7 5.5 5.0 4.2 

3.0 96 6.4 6.1 5.7 5.0 4.5 4.1 3.3 – 

3.5 110 4.2 3.7 3.2 2.6 – – – – 

1.5 

2.0 

3.0 

17 

18 

20 

22 

23 

27 

27 

29 

33 

3.4 

3.4 

3.4 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F23


External Mix, 1/8J and 1/4J Series 





Set-up 

No. 

SU1A 

SU1 


Set-up 


Fluid and 




+ 



+ 



Press. 




Capacity 

l/min 






45 30 15 10 20 30 60 90 

.70 11.3 1.5 1.3 1.1 .87 .68 .53 – – 

1.5 17.0 1.8 1.7 1.5 1.3 1.2 1.1 .62 – 

3.0 28 2.1 1.9 1.7 1.5 1.4 1.3 1.1 .76 

4.0 36 2.2 2.0 1.8 1.6 1.5 1.4 1.2 .87 

.70 13.3 2.4 2.1 1.7 1.5 1.2 .79 – – 

1.5 20 2.8 2.6 2.4 2.1 1.9 1.6 .91 – 

3.0 32 3.4 3.1 2.9 2.8 2.6 2.4 1.7 1.1 

4.0 41 3.7 3.4 3.3 3.1 2.9 2.7 2.1 1.5 


.70 

1.5 

3.0 

4.0 

.70 

1.5 

3.0 

4.0 




Angle 

A (°) 

18 

18 

18 

18 

18 

18 

18 

19 

B 

(cm) 

28 

28 

30 

36 

30 

33 

38 

43 

D 

(m) 

1.8 

1.9 

2.3 

2.6 

2.1 

2.3 

2.6 

3.0 

SU2A 


+ 


.70 23 2.5 2.3 2.0 1.6 1.4 1.1 – – 

1.5 36 2.9 2.8 2.5 2.2 2.0 1.7 .89 – 

3.0 58 3.4 3.3 3.2 2.9 2.8 2.5 1.9 1.2 

4.0 74 3.7 3.6 3.5 3.4 3.3 3.0 2.5 2.0 

.70 

1.5 

3.0 

4.0 

18 

18 

19 

20 

30 

33 

38 

43 

2.4 

2.7 

3.4 

4.0 

SU2 


+ 


.70 19.3 4.5 4.0 3.4 2.1 1.8 1.4 – – 

1.5 31 5.3 4.9 4.4 3.5 2.9 2.7 1.8 – 

3.0 50 6.0 5.6 5.0 4.4 4.0 3.4 2.4 1.2 

4.0 65 5.7 5.4 5.0 4.2 3.9 3.5 2.8 1.9 

.70 

1.5 

3.0 

4.0 

21 

21 

21 

22 

38 

41 

46 

51 

3.0 

3.4 

4.0 

4.6 

SU4 


+ 


1.5 58 22 19.9 16.3 12.3 10.5 8.3 2.8 – 

3.0 88 25 23 19.5 16.7 14.2 11.5 6.4 2.8 

4.0 111 26 24 21 18.4 15.7 12.9 7.9 4.5 

5.6 147 26 24 22 19.7 17.0 14.6 9.8 6.1 

1.5 

3.0 

4.0 

5.6 

17 

18 

18 

19 

46 

51 

53 

58 

3.7 

4.3 

4.9 

5.5 

SU5 


+ 


2.0 144 – – – 27 22 16.8 – – 

3.0 190 – – – 30 26 21 – – 

4.0 240 – 43 40 31 28 23 11.0 – 

5.6 315 44 42 39 31 28 24 16.7 8.3 

2.0 

3.0 

4.0 

5.6 

20 

20 

21 

22 

51 

53 

58 

63 

6.7 

7.0 

7.6 

8.2 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F24

Overview, 1/8JJ Compact Series 

1/8JJ Series air atomizing 


1/8JJ 

1 2 3 

4 

5 


1/8JJCO 

Clean-out 


1/8JJN 

1 2 3 



3. Fluid cap 

4. O-ring 7717-2/007 

4 

7 

6 



7. Back Seal Gasket 7222-BUC 

Shut-off 


Spray Set-up for Drip Free 

1/8JJAU – Drip Free 


needle assembly 



Applying lubricant to form presses in steel drum manufacturing. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F25





• Nozzle assembly consists of a body and spray set-up. 

• Various assemblies can be added to provide shut-off or 

clean-out functions. 

• 1/8JJ has liquid and air feeds at opposite ends of the body. 

• 1/8JJN features a manual shut-off needle that enables the flow 

of liquid to be stopped. 

• 1/8JJCO features a clean-out needle that is activated manually. 

– Needle slides through the liquid orifice to clear obstructions. 

– Ideal for intermittent spraying applications when liquid can 

dry in the orifice between uses. 



See Also 







– Strainers 

http:// 

1/8JJ 

1/8JJN 

1/8JJCO 

1/8" NPT or BSPT 1/8" NPT or BSPT with 

1/8" NPT or BSPT with 



Materials 

Ordering Info 

Material 

Nozzle Bodies 


Brass 

Material 


Nozzle Type 

JJ JJN JJCO 

(none) l l l 

303 Stainless Steel SS l l l 



Brass Air 

Cap and 

303 Stainless Steel 

Fluid Cap 

SSBR l l l 



Nozzle Body* 


1/8 JJN – SS + SUJ12A – SS 

l l l l l 

Inlet 


Nozzle 

Body 

Assembly 

Type 

Material 




Set-up 

No. 

Material 





performance data charts) and material code: J2050-SS. 


performance data charts) and material code: J73160-SS. 


connection, nozzle body and material code: 1/8JJN-SS. 



SUJ12A – SS 

l 

l 


Set-up 

No. 

Material 


To order spray set-up only, 

use spray set-up number and 

material code: SU12A-SS. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F26





• For round spray pattern, angle “A” is maintained throughout distance “B”. Beyond “B”, the spray 




Round spray and 360° circular 

spray air caps produce full cone 

round spray; air caps used in 

spray set-up SUJ340C produce 

360° circular spray pattern. 

Round spray 

pattern 

D 

12582 retainer ring and 7717-2/007 O-ring must be ordered separately from the spray set-up, but are included in 


B 

A 




Set-up 

No. 


Set-up 


Fluid and 




Press. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Liquid* 


Dimensions 


Angle 

A (°) 

B 

(cm) 

D 

(m) 



SUJ11 

Fluid Cap 

J2050 

+ 


J67147 

.70 2.5 15.6 1.1 6.4 11.9 1.4 6.4 13.9 2.7 6.2 23 3.5 7.8 28 

.85 1.8 19.0 1.4 5.0 15.0 1.7 5.5 16.7 2.8 5.7 25 3.7 7.3 29 

1.0 1.4 22 1.7 4.1 18.7 2.0 4.5 19.8 3.0 5.2 27 3.9 6.4 33 

– – – 2.0 3.0 23 2.4 3.0 26 3.2 4.3 31 4.5 4.5 43 

– – – 2.2 2.0 27 2.7 2.3 31 3.7 3.0 38 4.8 3.7 47 

.85 

1.7 

2.5 

3.1 

4.5 

.70 

1.5 

2.0 

3.0 

4.0 

13 

13 

13 

14 

15 

30 

33 

36 

39 

44 

2.7 

3.0 

3.4 

3.8 

4.4 

SUJ12A 

Fluid Cap 

J2050 

+ 


J73160 

.70 2.5 18.7 1.4 5.7 27 1.7 6.7 29 2.2 9.2 34 2.8 11.9 39 

.85 2.0 22 1.5 5.2 29 1.8 6.4 31 2.5 8.2 39 3.1 11.0 43 

1.0 1.6 26 1.7 4.8 32 2.0 5.9 34 2.8 7.2 44 3.4 10.1 47 

– – – 2.0 3.9 37 2.2 4.8 40 3.1 6.3 49 3.9 8.4 58 

– – – 2.1 3.4 40 2.7 3.6 48 3.4 5.5 55 4.5 6.8 68 

.85 

1.5 

2.4 

3.0 

3.9 

.70 

1.5 

2.0 

3.0 

4.0 

12 

13 

13 

13 

15 

43 

46 

48 

51 

56 

3.7 

4.0 

4.3 

4.6 

5.2 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F27







Set-up 

No. 

SUJ12 


Set-up 


Fluid and 



Fluid Cap 

J2850 

+ 


J73160 


Press. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.85 4.8 21 1.7 8.4 31 2.0 10.7 33 2.7 16.5 37 3.4 20 43 

1.1 4.1 27 1.8 7.5 35 2.1 9.8 37 2.8 15.4 38 3.7 18.4 47 

1.4 3.4 33 2.0 7.0 37 2.4 8.2 42 3.1 13.6 43 3.9 16.8 50 

1.7 3.0 39 2.5 4.8 49 3.0 5.9 55 3.7 10.4 55 4.5 13.8 60 

2.0 2.8 44 3.1 3.6 59 3.5 4.1 65 4.2 7.9 65 4.9 11.8 68 

l/h 


l/min 


1.5 

2.5 

3.0 

3.4 

4.2 

Liquid* 

.70 

1.5 

2.0 

3.0 

4.0 


Dimensions 


Angle 

A (°) 

12 

13 

13 

14 

15 

B 

(cm) 

48 

51 

53 

56 

60 

D 

(m) 

4.0 

4.3 

4.6 

4.9 

5.3 

SUJ22B 

Fluid Cap 

J40100 

+ 


J1401110 

1.1 13.0 76 2.2 17.8 116 2.8 20 136 3.4 32 149 4.6 37 190 

1.4 8.9 91 2.5 13.1 130 3.1 16.3 149 3.9 25 170 5.3 29 220 

1.5 7.2 98 2.8 9.5 143 3.4 11.9 163 4.6 15.9 205 5.6 25 235 

1.8 4.7 112 3.4 4.9 171 4.2 4.7 205 5.6 6.8 255 6.3 17.4 270 

2.1 2.7 127 3.5 4.2 178 4.6 3.0 220 6.3 3.6 290 7.0 11.0 305 

1.7 

2.8 

3.9 

5.3 

6.0 

.70 

1.5 

2.0 

3.0 

4.0 

18 

20 

20 

21 

21 

66 

76 

81 

91 

97 

4.9 

6.1 

6.7 

7.9 

9.1 

SUJ22 

Fluid Cap 

J60100 

+ 


J1401110 

.85 31 57 1.4 61 69 2.1 53 96 2.7 80 103 3.8 88 135 

1.0 25 66 1.5 54 76 2.4 41 112 3.0 69 117 4.2 73 156 

1.1 18.5 75 1.7 48 85 2.7 31 127 3.2 59 130 4.6 61 176 

1.3 12.9 85 2.0 35 102 2.8 26 136 3.7 44 154 5.3 39 215 

– – – 2.2 25 119 3.0 22 144 3.9 35 170 6.0 23 260 

1.0 

1.8 

2.8 

3.5 

4.9 

.70 

1.5 

2.0 

3.0 

4.0 

17 

18 

20 

20 

21 

61 

69 

76 

79 

91 

4.9 

5.8 

6.7 

7.0 

8.5 

360° Circular Spray† 


Set-up 

No. 

SUJ340C 


Set-up 


Fluid and 



Fluid Cap 

J60100 

+ 


J150-6-62- 

160HC 


Press. 

†Use only with 1/8JJAU automatic air atomizing nozzles. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

1.4 15.1 69 2.8 19.5 142 3.5 21 185 4.2 48 210 6.0 45 340 

1.5 10.6 77 3.0 16.1 153 3.7 17.6 196 4.6 37 240 6.3 37 375 

1.7 7.6 84 3.1 13.2 165 3.8 14.8 210 4.9 28 275 6.7 30 405 

1.8 5.7 93 3.2 10.6 177 3.9 12.5 220 5.6 15.5 340 7.0 24 440 

2.0 4.2 103 3.4 8.3 188 4.2 8.1 245 6.3 7.8 425 – – – 


Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F28




Wide angle round and flat spray 

air caps produce hollow cone 

type, wide angle round spray 



• For wide angle round and flat sprays, dimensions “A”, “B” and “C” are the pattern widths at 

distances from the nozzle. 





Wide angle round 

spray pattern 

D 

C 

12582 retainer ring and 7717-2/007 O-ring must be ordered separately from the spray set-up, but are included in 


B 

A 

6" 

(15 cm) 

9" (23 cm) 

15" (38 cm) 







Set-up 

No. 


Set-up 


Fluid and 




Press. 



0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Liquid* 


Dimensions 

A 

(cm) 

B 

(cm) 

C 

(cm) 

D 

(m) 

SUJ16 

SUJ26B 

SUJ26 

SUJ29 

SUJ30 

Fluid Cap 

J2050 

+ 


J67-6-20-70° 

Fluid Cap 

J40100 

+ 


J140-6-37-70° 

Fluid Cap 

J60100 

+ 


J140-6-37-70° 

Fluid Cap 

J60100 

+ 


J140-6-52-70° 

Fluid Cap 

J40100 

+ 


J120-6-35-60° 

.60 5.3 10.2 1.1 8.1 13.3 1.5 8.1 16.4 2.4 8.9 22 3.1 10.5 24 

.70 4.3 12.2 1.3 7.0 15.0 1.8 6.6 21 2.7 8.1 26 3.4 9.7 28 

.85 3.0 14.2 1.4 6.4 17.0 2.1 4.9 25 3.0 6.4 30 3.9 7.8 36 

1.0 1.7 17.0 1.7 4.5 22 2.4 3.2 29 3.4 4.2 37 4.6 4.4 47 

– – – 1.8 3.5 24 – – – 3.5 3.4 40 4.9 2.8 54 

.85 7.0 50 1.7 13.2 68 2.0 18.5 68 2.8 25 84 3.7 31 96 

1.0 2.1 62 1.8 9.8 79 2.1 15.1 76 3.0 22 92 3.8 28 105 

– – – – – – 2.2 11.7 85 3.1 18.5 101 3.9 26 113 

– – – – – – – – – 3.4 12.1 119 4.2 20 130 

– – – – – – – – – 3.7 6.1 142 4.9 6.8 183 

.70 24 32 1.4 43 37 2.1 33 66 2.8 52 65 3.7 63 68 

.85 13.6 44 1.5 35 49 2.2 26 78 3.0 46 76 3.8 58 79 

1.0 7.6 57 1.7 28 61 2.4 18.9 89 3.1 39 87 3.9 52 101 

– – – 1.8 21 71 2.5 11.7 100 3.4 26 110 4.6 27 138 

– – – – – – – – – 3.7 13.2 133 4.9 15.9 166 

1.3 36 85 2.1 57 116 3.1 53 156 4.2 64 197 5.6 74 245 

1.5 29 102 2.4 51 130 3.2 50 163 4.9 51 230 6.0 68 260 

1.8 23 117 2.7 45 143 3.4 47 170 5.6 40 265 6.3 62 280 

2.1 16.7 133 3.2 33 170 3.9 38 194 6.3 28 300 6.7 56 295 

2.4 11.4 149 4.2 13.6 220 4.9 18.5 245 7.0 17.8 335 7.0 51 315 

1.1 12.3 40 2.2 16.3 62 2.7 21 69 4.2 19.3 100 5.6 22 130 

1.3 9.9 45 2.5 12.1 71 3.0 16.3 78 4.6 14.6 113 6.0 17.6 142 

1.4 7.9 50 2.8 8.9 79 3.2 12.3 86 4.9 10.8 124 6.3 14.0 152 

1.7 4.9 58 3.1 6.4 87 3.5 9.3 94 5.6 6.2 146 6.7 11.4 163 

2.0 3.1 67 3.4 4.7 95 4.2 4.7 115 6.3 4.0 167 7.0 9.1 174 

.70 

1.4 

1.8 

3.0 

3.9 

.85 

1.7 

2.1 

3.2 

4.1 

.85 

1.5 

2.4 

3.2 

3.9 

2.0 

3.0 

3.9 

6.0 

6.3 

1.5 

3.0 

3.4 

5.3 

6.3 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

14 

15 

16 

16 

19 

18 

19 

19 

20 

21 

19 

20 

20 

20 

20 

20 

20 

22 

23 

24 

15 

16 

16 

18 

19 

18 

19 

20 

20 

23 

24 

25 

25 

26 

28 

25 

27 

27 

28 

28 

25 

27 

28 

29 

32 

17 

20 

20 

22 

24 

23 

24 

25 

26 

30 

31 

33 

33 

34 

37 

36 

37 

37 

38 

39 

33 

34 

37 

38 

41 

23 

24 

24 

25 

30 

1.5 

1.8 

2.1 

2.7 

4.0 

1.8 

2.4 

3.2 

4.1 

5.9 

2.1 

3.2 

4.1 

5.0 

6.8 

5.5 

6.4 

8.2 

9.1 

10.4 

2.7 

4.6 

5.5 

7.3 

9.4 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F29







Set-up 

No. 

SUJ13A 


Set-up 


Fluid and 



Fluid Cap 

J2050 

+ 


J73328 


Press. 




0.7 1.5 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

.70 5.5 24 1.3 9.1 31 2.0 8.6 42 2.7 11.2 52 3.9 12.0 69 

.85 4.7 27 1.5 7.7 36 2.2 7.5 47 3.0 10.1 56 4.6 9.7 81 

1.0 4.1 31 1.8 6.5 42 2.5 6.2 52 3.2 9.1 62 5.3 7.5 93 

l/h 


l/min 

1.3 3.0 37 2.4 4.3 52 3.1 4.2 63 4.2 5.4 79 6.3 4.3 110 

1.5 2.0 44 2.8 2.8 60 3.4 3.2 68 4.9 3.1 91 7.0 2.4 122 


1.1 

2.1 

2.8 

3.5 

6.0 

Liquid* 

.70 

1.5 

2.0 

3.0 

4.0 


Dimensions 

A 

(cm) 

25 

36 

38 

47 

56 

B 

(cm) 

36 

48 

53 

61 

74 

C 

(cm) 

46 

66 

76 

86 

94 

D 

(m) 

2.6 

3.0 

3.2 

3.4 

4.0 

SUJ13 

Fluid Cap 

J2850 

+ 


J73328 

.85 8.2 19.8 1.4 14.4 27 2.1 13.5 36 2.7 19.1 42 4.6 16.1 69 

1.0 6.8 23 1.7 11.9 32 2.4 11.4 42 3.0 17.1 46 4.9 13.8 76 

1.1 5.5 27 2.0 9.5 37 2.7 9.2 47 3.2 15.1 52 5.3 11.5 83 

1.3 4.1 30 2.2 7.1 43 3.2 5.0 59 4.2 8.1 72 6.0 7.3 97 

1.4 2.9 34 2.5 5.1 49 3.5 3.3 66 4.9 4.0 86 6.7 4.3 112 

1.1 

2.1 

3.0 

3.5 

5.6 

.70 

1.5 

2.0 

3.0 

4.0 

36 

43 

51 

58 

58 

46 

61 

66 

76 

76 

71 

81 

89 

97 

97 

2.1 

2.4 

2.6 

2.7 

3.2 

SUJ14 

Fluid Cap 

J2850 

+ 


J73320 

1.3 3.9 30 2.1 7.4 40 3.0 6.1 52 3.9 9.4 60 5.3 10.2 78 

1.4 3.0 33 2.4 5.3 45 3.1 5.3 54 4.2 7.2 67 5.6 8.3 84 

1.5 2.3 35 2.5 4.4 47 3.2 4.5 57 4.6 5.3 73 6.0 6.6 89 

1.8 1.3 41 2.8 3.1 52 3.5 3.2 62 4.9 3.8 80 6.3 5.1 98 

2.0 .95 44 3.1 2.1 57 3.9 1.8 68 – – – – – – 

1.5 

2.7 

3.2 

4.2 

5.6 

.70 

1.5 

2.0 

3.0 

4.0 

25 

36 

58 

61 

64 

33 

51 

74 

74 

76 

46 

69 

91 

94 

97 

1.8 

2.0 

2.0 

2.1 

2.3 

SUJ23B 

Fluid Cap 

J40100 

+ 


J125328 

1.1 11.2 54 2.1 18.0 79 2.7 19.6 93 3.5 27 112 4.6 33 137 

1.3 8.5 60 2.2 15.8 84 2.8 17.3 98 3.7 25 116 4.9 28 149 

1.4 6.5 65 2.4 13.6 89 3.0 15.2 103 3.8 23 121 5.3 27 161 

1.5 5.0 71 2.5 11.6 95 3.1 13.2 109 3.9 21 126 5.6 19.7 174 

1.7 3.8 77 – – – 3.2 11.4 114 4.2 17.0 137 6.3 12.4 200 

1.4 

2.4 

3.0 

3.7 

5.3 

.70 

1.5 

2.0 

3.0 

4.0 

15 

23 

25 

30 

33 

18 

28 

33 

38 

41 

20 

33 

46 

46 

48 

3.0 

3.2 

3.4 

3.5 

4.0 

SUJ23 

Fluid Cap 

J60100 

+ 


J125328 

.85 27 33 1.8 38 55 2.4 39 67 3.2 58 76 4.6 59 106 

1.0 20 38 2.1 28 66 2.7 30 77 3.5 47 87 5.3 40 132 

1.1 15.9 45 2.2 24 71 3.0 24 87 3.8 38 97 5.6 32 145 

1.4 10.2 56 2.5 17.8 82 3.4 15.1 103 4.2 27 113 6.3 20 172 

1.5 7.6 62 2.7 15.1 87 3.7 10.6 114 4.9 14.8 140 7.0 12.7 198 

1.1 

2.4 

3.2 

3.9 

6.0 

.70 

1.5 

2.0 

3.0 

4.0 

18 

23 

25 

30 

33 

23 

30 

33 

38 

41 

30 

41 

43 

48 

51 

3.4 

3.5 

3.7 

3.8 

4.4 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F30


High Capacity, 1/8JJ Compact Series 


• Offers an increased ability to atomize viscous fluids and allows 

for greater capacities of finely atomized sprays. 

• Simple, one-piece, low-profile design permits larger air passage. 

More air can be brought in to atomize the liquid stream. 

• Atomization can be controlled by varying the air pressure without 

changing liquid flow rates. 

• When using a pressure-fed liquid system, the liquid is supplied to 

the nozzle under pressure. 


External mix air caps 

produce a flat spray pattern. 




Set-up 

No. 

SUJE416-50 

SUJE417-50 

SUJE418-50 

SUJE420-50 

SUJE421-50 


Set-up 


Fluid and 



Fluid Cap 

PFJ1650 

+ 


PAJ105-50 

Fluid Cap 

PFJ2050 

+ 


PAJ105-50 

Fluid Cap 

PFJ2850 

+ 


PAJ105-50 

Fluid Cap 

PFJ40100 

+ 


PAJ135-50 

Fluid Cap 

PFJ60100 

+ 


PAJ135-50 


Press. 




0.7 1.5 2 2.5 

l/h 


l/min 


Press. 

l/h 


l/min 

Flat spray 

pattern 

D 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

0.7 4.9 65.1 0.7 7.4 65.1 0.7 8.4 65.1 0.7 9.2 65.1 

1.4 4.9 104.8 1.4 7.4 104.8 1.4 8.4 104.8 1.4 9.2 104.8 

2.1 4.9 141.6 2.1 7.4 141.6 2.1 8.4 141.6 2.1 9.2 141.6 

2.8 4.9 175.6 2.8 7.4 175.6 2.8 8.4 175.6 2.8 9.2 175.6 

3.4 4.9 209.5 3.4 7.4 209.5 3.4 8.4 209.5 3.4 9.2 209.5 

0.7 7.2 65.1 0.7 10.8 65.1 0.7 12.3 65.1 0.7 13.5 65.1 

1.4 7.2 104.8 1.4 10.8 104.8 1.4 12.3 104.8 1.4 13.5 104.8 

2.1 7.2 141.6 2.1 10.8 141.6 2.1 12.3 141.6 2.1 13.5 141.6 

2.8 7.2 175.6 2.8 10.8 175.6 2.8 12.3 175.6 2.8 13.5 175.6 

3.4 7.2 209.5 3.4 10.8 209.5 3.4 12.3 209.5 3.4 13.5 209.5 

0.7 11.0 65.1 0.7 23.4 65.1 0.7 27.8 65.1 0.7 31.1 65.1 

1.4 11.0 104.8 1.4 23.4 104.8 1.4 27.8 104.8 1.4 31.1 104.8 

2.1 11.0 141.6 2.1 23.4 141.6 2.1 27.8 141.6 2.1 31.1 141.6 

2.8 11.0 175.6 2.8 23.4 175.6 2.8 27.8 175.6 2.8 31.1 175.6 

3.4 11.0 209.5 3.4 23.4 209.5 3.4 27.8 209.5 3.4 31.1 209.5 

0.7 44.3 65.1 0.7 47.7 65.1 0.7 54.4 65.1 0.7 61.5 65.1 

1.4 44.3 104.8 1.4 47.7 104.8 1.4 54.4 104.8 1.4 61.5 104.8 

2.1 44.3 141.6 2.1 47.7 141.6 2.1 54.4 141.6 2.1 61.5 141.6 

2.8 44.3 172.7 2.8 47.7 172.7 2.8 54.4 172.7 2.8 61.5 172.7 

3.4 44.3 206.7 3.4 47.7 206.7 3.4 54.4 206.7 3.4 61.5 206.7 

2.1 – – 2.1 – – 2.1 – – 2.1 – – 

2.8 – – 2.8 – – 2.8 – – 2.8 – – 

3.4 – – 3.4 – – 3.4 – – 3.4 – – 

4.1 – – 4.1 – – 4.1 – – 4.1 122.3 240.7 

4.8 – – 4.8 – – 4.8 – – 4.8 122.3 274.7 

• The liquid and compressed air or gas are mixed externally to 

produce a completely atomized spray. 

• SUJE Spray Set-up Series is both compact and air efficient. 

• Offered in three spray angles – 50°, 65° and 90°. 

• SUJE Series features lower spray velocity for improved transfer and 

reduced misting and is ideal for applications where space is limited. 

• Very efficient use of air results in reduced air consumption costs 

and noise levels. 

• Simple four-part assembly allows easy installation and maintenance. 

C 

B 

A 

6" 

(15 cm) 

9" (23 cm) 

15" (38 cm) 

CP46259 retainer ring and 

CP7717-2/007-VI O-ring must be 

ordered separately from the spray 

set-up, but are included in the 

standard nozzle assembly. The 46599 

adapter is used with all 1/8JJ nozzle 

bodies and automatic spray guns 

with extensions, but not on 1/8JJAU 

spray guns without extensions. 

Please contact your sales engineer. 


Angle 

50° 



Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F31


High Capacity, 1/8JJ Compact Series 





Set-up 

No. 

SUJE416-65 

SUJE417-65 

SUJE418-65 

SUJE420-65 

SUJE421-65 

SUJE416-90 

SUJE417-90 

SUJE418-90 

SUJE420-90 

SUJE421-90 


Set-up 


Fluid and 



Fluid Cap 

PFJ1650 

+ 


PAJ080-65 

Fluid Cap 

PFJ2050 

+ 


PAJ080-65 

Fluid Cap 

PFJ2850 

+ 


PAJ080-65 

Fluid Cap 

PFJ40100 

+ 


PAJ125-65 

Fluid Cap 

PFJ60100 

+ 


PAJ125-65 

Fluid Cap 

PFJ1650 

+ 


PAJ075-90 

Fluid Cap 

PFJ2050 

+ 


PAJ075-90 

Fluid Cap 

PFJ2850 

+ 


PAJ075-90 

Fluid Cap 

PFJ40100 

+ 


PAJ115-90 

Fluid Cap 

PFJ60100 

+ 


PAJ115-90 


Press. 




0.7 1.5 2 2.5 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

0.7 4.9 53.8 0.7 7.4 53.8 0.7 8.4 53.8 0.7 9.2 53.8 

1.4 4.9 85.0 1.4 7.4 85.0 1.4 8.4 85.0 1.4 9.2 85.0 

2.1 4.9 113.3 2.1 7.4 113.3 2.1 8.4 113.3 2.1 9.2 113.3 

2.8 4.9 141.6 2.8 7.4 141.6 2.8 8.4 141.6 2.8 9.2 141.6 

3.4 4.9 167.1 3.4 7.4 167.1 3.4 8.4 167.1 3.4 9.2 167.1 

0.7 7.2 53.8 0.7 10.8 53.8 0.7 12.3 53.8 0.7 13.5 53.8 

1.4 7.2 85.0 1.4 10.8 85.0 1.4 12.3 85.0 1.4 13.5 85.0 

2.1 7.2 113.3 2.1 10.8 113.3 2.1 12.3 113.3 2.1 13.5 113.3 

2.8 7.2 141.6 2.8 10.8 141.6 2.8 12.3 141.6 2.8 13.5 141.6 

3.4 7.2 167.1 3.4 10.8 167.1 3.4 12.3 167.1 3.4 13.5 167.1 

0.7 11.0 53.8 0.7 23.3 53.8 0.7 27.7 53.8 0.7 31.2 53.8 

1.4 11.0 85.0 1.4 23.3 85.0 1.4 27.7 85.0 1.4 31.2 85.0 

2.1 11.0 113.3 2.1 23.3 113.3 2.1 27.7 113.3 2.1 31.2 113.3 

2.8 11.0 141.6 2.8 23.3 141.6 2.8 27.7 141.6 2.8 31.2 141.6 

3.4 11.0 167.1 3.4 23.3 167.1 3.4 27.7 167.1 3.4 31.2 167.1 

0.7 30.3 59.5 0.7 47.7 59.5 0.7 54.4 59.5 0.7 59.7 59.5 

1.4 30.3 93.5 1.4 47.7 93.5 1.4 54.4 93.5 1.4 59.7 93.5 

2.1 30.3 124.6 2.1 47.7 124.6 2.1 54.4 124.6 2.1 59.7 124.6 

2.8 30.3 152.9 2.8 47.7 152.9 2.8 54.4 152.9 2.8 59.7 152.9 

3.4 30.3 184.1 3.4 47.7 184.1 3.4 54.4 184.1 3.4 59.7 184.1 

2.1 60.6 124.6 2.1 – – 2.1 – – 2.1 – – 

2.8 60.6 152.9 2.8 94.9 152.9 2.8 – – 2.8 – – 

3.4 60.6 184.1 3.4 94.9 184.1 3.4 108.2 184.1 3.4 – – 

0.7 4.9 53.8 0.7 7.4 53.8 0.7 8.4 53.8 0.7 9.2 53.8 

1.4 4.9 85.0 1.4 7.4 85.0 1.4 8.4 85.0 1.4 9.2 85.0 

2.1 4.9 113.3 2.1 7.4 113.3 2.1 8.4 113.3 2.1 9.2 113.3 

2.8 4.9 141.6 2.8 7.4 141.6 2.8 8.4 141.6 2.8 9.2 141.6 

3.4 4.9 167.1 3.4 7.4 167.1 3.4 8.4 167.1 3.4 9.2 167.1 

0.7 7.2 53.8 0.7 10.8 53.8 0.7 12.3 53.8 0.7 13.5 53.8 

1.4 7.2 85.0 1.4 10.8 85.0 1.4 12.3 85.0 1.4 13.5 85.0 

2.1 7.2 113.3 2.1 10.8 113.3 2.1 12.3 113.3 2.1 13.5 113.3 

2.8 7.2 141.6 2.8 10.8 141.6 2.8 12.3 141.6 2.8 13.5 141.6 

3.4 7.2 167.1 3.4 10.8 167.1 3.4 12.3 167.1 3.4 13.5 167.1 

0.7 11.0 53.8 0.7 24.3 53.8 0.7 27.9 53.8 0.7 30.8 53.8 

1.4 11.0 85.0 1.4 24.3 85.0 1.4 27.9 85.0 1.4 30.8 85.0 

2.1 11.0 113.3 2.1 24.3 113.3 2.1 27.9 113.3 2.1 30.8 113.3 

2.8 11.0 141.6 2.8 24.3 141.6 2.8 27.9 141.6 2.8 30.8 141.6 

3.4 11.0 167.1 3.4 24.3 167.1 3.4 27.9 167.1 3.4 30.8 167.1 

1.4 30.3 82.1 1.4 – – 1.4 – – 1.4 – – 

2.1 30.3 110.4 2.1 44.3 110.4 2.1 – – 2.1 – – 

2.8 30.3 135.9 2.8 44.3 135.9 2.8 54.4 135.9 2.8 – – 

3.4 30.3 161.4 3.4 44.3 161.4 3.4 54.4 161.4 3.4 63.2 161.4 

2.1 60.6 110.4 2.1 – – 2.1 – – 2.1 – – 

2.8 60.6 135.9 2.8 94.9 135.9 2.8 – – 2.8 – – 

3.4 60.6 161.4 3.4 94.9 161.4 3.4 108.2 161.4 3.4 – – 

4.1 – – 4.1 – – 4.1 – – 4.1 118.6 186.9 

4.8 – – 4.8 – – 4.8 – – 4.8 118.6 212.4 


Angle 

65° 

90° 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F32


Air Efficient, 1/8JJ Compact Series 


Elliptical 

spray pattern 

A 

Internal mix air caps produce 

an elliptical spray pattern. 

D 


Elliptical Spray/Air Efficient (Internal Mix) 


Set-up 

No. 

SUJ400 

SUJ401 


Set-up 


Fluid and 



Fluid Cap 

PFJ16225 

+ 


PAJ14739 

Fluid Cap 

PFJ20232 

+ 


PAJ132-50 


Press. 




1 1.5 2 2.5 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

– – – – – – – – – 4.1 .64 30.6 4.1 3.0 28.6 4.1 6.3 26.1 

– – – – – – 3.5 .57 26.3 3.5 2.6 24.8 3.5 4.2 23.2 3.5 7.4 21 

– – – – – – 2.8 2.7 20.4 2.8 4.2 20.1 2.8 5.7 18.1 2.8 8.7 15.2 

– – – 2.4 .95 18.7 2.4 4.0 16.4 2.4 5.4 15.6 2.4 6.8 14.7 2.4 9.3 13.2 

– – – 2.1 2.6 15.3 2.1 5.0 13.6 2.1 6.3 13.5 2.1 7.6 12.5 2.1 9.7 11.9 

1.7 1.1 14.2 1.7 3.7 12.8 1.7 5.7 11.8 1.7 6.9 11.1 1.7 8.4 10.2 1.7 10.5 9.1 

1.4 2.6 11.3 1.4 4.6 10.7 1.4 6.4 9.6 1.4 7.5 9.1 1.4 9.5 7.9 – – – 

1.0 3.7 9.2 1.0 5.6 8.3 1.0 7.2 7.4 1.0 8.3 6.3 – – – – – – 

– – – – – – – – – – – – 4.1 2.3 47.4 4.1 8.2 41.4 

– – – – – – – – – 3.5 2.4 39.7 3.5 6.4 36.9 3.5 10.2 32.9 

– – – – – – 2.8 2.6 32.9 2.8 5.7 30 2.8 8.9 28.2 2.8 12.5 24.9 

– – – 2.1 3.3 25.5 2.1 6.1 22.7 2.1 8.7 21 2.1 11.2 19.0 2.1 14.7 17.0 

– – – 1.7 4.5 20.4 1.7 8.2 17.0 1.7 10.2 16.4 1.7 12.4 15.2 1.7 15.5 13.4 

– – – 1.4 6.8 15.9 1.4 9.5 14.2 1.4 11.4 13.0 1.4 13.3 11.8 1.4 16.3 9.9 

– – – 1.0 8.3 11.3 1.0 10.8 10.2 1.0 12.5 9.6 1.0 14.4 8.5 1.0 17.0 7.6 

.70 4.3 10.2 .70 9.5 7.9 .70 12.0 6.8 .70 13.6 6.8 .70 15.3 5.7 .70 17.8 4.9 

l/h 


l/min 


0.7 

1.4 

0.7 

1.4 


Dimensions 

0.7 

1.4 

0.7 

1.4 


Angle 

A (°) 

35 

30 

35 

30 

D 

(cm) 

61 

76 

66 

81 



Tabulation is based on spraying air and water at room temperature under laboratory conditions. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F33


External Mix, 1/8JJ Compact Series 



Round spray air caps produce 

a full cone round spray pattern. 


• For round spray pattern, angle “A” is maintained throughout distance “B”. Beyond “B”, 

the spray becomes turbulent and will project out to distance “D”. 

• When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid 

siphon or a gravity-feed. 

• Designed to draw liquid through the feed line into the air flow where it is atomized. 

Round spray 

pattern 

D 

B 

A 

12582 retainer ring and 7717-2/007 O-ring must be ordered separately from the spray set-up, 

but are included in the standard nozzle assembly. Please contact your sales engineer. 





Set-up 

No. 


Set-up 


Fluid and 




Press. 




Capacity 

l/min 





45 30 15 10 20 30 60 90 





Angle 

A (°) 

B 

(cm) 

D 

(m) 

SUJ1A 

Fluid Cap J1650 

+ 

Air Cap J64 

.70 11.3 1.5 1.3 1.1 .87 .68 .53 – – 

1.5 17.0 1.8 1.7 1.5 1.3 1.2 1.1 .62 – 

3.0 28 2.1 1.9 1.7 1.5 1.4 1.3 1.1 .76 

4.0 36 2.2 2.0 1.8 1.6 1.5 1.4 1.2 .87 

.70 

1.5 

3.0 

4.0 

18 

18 

18 

18 

28 

28 

30 

36 

1.8 

1.9 

2.3 

2.6 

SUJ1 


+ 


.70 13.3 2.4 2.1 1.7 1.5 1.2 .79 – – 

1.5 20 2.8 2.6 2.4 2.1 1.9 1.6 .91 – 

3.0 32 3.4 3.1 2.9 2.8 2.6 2.4 1.7 1.1 

4.0 41 3.7 3.4 3.3 3.1 2.9 2.7 2.1 1.5 

.70 

1.5 

3.0 

4.0 

18 

18 

18 

19 

30 

33 

38 

43 

2.1 

2.3 

2.6 

3.0 

SUJ2A 


+ 


.70 23 2.5 2.3 2.0 1.6 1.4 1.1 – – 

1.5 36 2.9 2.8 2.5 2.2 2.0 1.7 .89 – 

3.0 58 3.4 3.3 3.2 2.9 2.8 2.5 1.9 1.2 

4.0 74 3.7 3.6 3.5 3.4 3.3 3.0 2.5 2.0 

.70 

1.5 

3.0 

4.0 

18 

18 

19 

20 

30 

33 

38 

43 

2.4 

2.7 

3.4 

4.0 

SUJ2 


+ 


.70 19.3 4.5 4.0 3.4 2.1 1.8 1.4 – – 

1.5 31 5.3 4.9 4.4 3.5 2.9 2.7 1.8 – 

3.0 50 5.7 5.4 5.0 4.2 3.9 3.4 2.4 1.2 

4.0 65 6.0 5.6 5.0 4.4 4.0 3.5 2.8 1.9 

.70 

1.5 

3.0 

4.0 

21 

21 

21 

22 

38 

41 

46 

51 

3.0 

3.4 

4.0 

4.6 

SUJ3 


+ 

Air Cap J64-5 

.70 11.6 – – – 2.2 1.9 1.1 – – 

1.5 18.4 – 4.8 4.1 3.6 3.2 2.6 1.2 – 

3.0 29 6.4 6.0 5.6 5.2 4.8 4.4 2.8 1.2 

4.0 37 7.1 6.7 6.3 6.1 5.6 5.3 3.7 2.0 

.70 

1.5 

3.0 

4.0 

18 

18 

18 

19 

30 

33 

38 

43 

2.4 

2.7 

3.4 

4.0 

SUJ4B 

Fluid Cap 

J40100 

+ 


.70 37 – – – 5.3 3.7 2.2 – – 

1.5 59 – 9.9 9.2 7.4 6.0 4.8 1.5 – 

3.0 91 12.1 11.3 10.7 8.8 7.7 6.5 3.0 1.1 

4.0 116 12.9 12.1 11.4 9.5 8.6 7.6 4.2 1.8 

.70 

1.5 

3.0 

4.0 

17 

17 

18 

19 

46 

48 

53 

58 

3.0 

3.4 

4.0 

4.6 

SUJ4 

Fluid Cap 

J60100 

+ 


1.5 57 22 19.9 16.3 12.3 10.5 8.3 2.8 – 

3.0 88 25 23 19.5 16.7 14.2 11.5 6.4 2.8 

4.0 111 26 24 21 18.4 15.7 12.9 7.9 4.5 

5.6 147 26 24 22 19.7 17.0 14.6 9.8 6.1 

1.5 

3.0 

4.0 

5.6 

17 

18 

18 

19 

46 

51 

53 

58 

3.7 

4.3 

4.9 

5.5 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F34


External Mix, 1/8JJ Compact Series 



• For flat spray pattern, dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle. 

• Total distance of spray projection from the nozzle to the maximum dispersal point is represented by “D”. 

Flat spray air caps produce 

a flat spray pattern. 

Flat spray 

pattern 

C 

B 

A 

D 

6" 

(15 cm) 

9" (23 cm) 

15" (38 cm) 





Set-up 

No. 


Set-up 


Fluid and 




Press. 




Capacity 

l/min 





45 30 15 10 20 30 60 90 




A 

(cm) 

B 

(cm) 

C 

(cm) 

D 

(m) 



SUJF1 


+ 


.70 28 1.3 1.2 1.1 1.0 .95 .83 .64 .49 

1.5 43 1.2 1.1 1.0 .90 .86 .78 .66 .54 

2.0 50 .82 .76 .68 .57 .50 – – – 

.70 

1.5 

2.0 

20 

21 

23 

26 

29 

30 

38 

38 

38 

2.1 

2.1 

1.8 

SUJF2C 


+ 


1.5 56 3.7 3.5 3.3 2.9 2.8 2.5 2.3 2.1 

2.0 65 3.4 3.3 3.1 2.8 2.7 2.6 2.4 2.2 

3.0 87 2.8 2.7 2.5 2.4 2.2 2.1 1.9 1.7 

4.0 110 1.9 1.8 1.6 1.5 1.3 1.2 – – 

1.5 

2.0 

3.0 

4.0 

23 

24 

27 

28 

32 

34 

37 

39 

38 

42 

46 

48 

2.7 

2.7 

3.0 

2.7 

SUJF3B 


+ 


1.5 68 5.1 4.8 4.5 3.8 3.7 3.5 3.0 2.4 

2.0 78 4.9 4.7 4.4 3.6 3.4 3.2 2.9 2.3 

3.0 103 3.4 3.2 3.0 2.2 2.0 1.7 – – 

3.5 117 2.2 2.0 1.7 – – – – – 

1.5 

2.0 

3.0 

19 

20 

22 

23 

25 

27 

27 

28 

30 

3.4 

3.4 

3.0 

SUJF4B 


+ 


1.5 63 7.6 7.2 6.6 5.7 5.4 5.1 4.6 3.7 

2.0 73 7.6 7.3 6.8 5.9 5.7 5.5 5.0 4.2 

3.0 96 6.4 6.1 5.7 5.0 4.5 4.1 3.3 – 

3.5 110 4.2 3.7 3.2 2.6 – – – – 

1.5 

2.0 

3.0 

17 

18 

20 

22 

23 

27 

27 

29 

33 

3.4 

3.4 

3.4 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F35

Overview/Nozzle Bodies/Nozzle Assemblies, 

VAU and VMAU Series 


1/8VAA 

1/8VAAN 

1/8VAACO 

Variable Spray Series 

air atomizing nozzles 


1 2 3 4 5 

Plug 29155-001-SS 

Shut-off needle assembly 

29535-001-SS 

Clean-out needle assembly 

29156 

1/8VAANCO 

1. Cap ring 28207-101-SS 


3. Fluid cap 

4. Nozzle body 29074-001-SS 

5. Washer 29154-001-BUC 

Shut-off/clean-out needle assembly 

29534 

1/8VAU 


• The VAA, VAU and VMAU variable spray nozzles provide uniform 

spray distribution, even when spraying viscous liquids. 

• Independent control of liquid, atomizing air, and fan air pressures 

is possible for fine-tuning of flow rate, drop size, spray distribution 

and coverage. 

• Can be set and re-set in seconds, simplifying application changes. 

• Independent air atomizing line can be adjusted to vary spray drop 

size without affecting liquid flow rates. 

• Additional inlet/outlet port allows for liquid recirculation that 

effectively maintains the flow of viscous liquids. 

• VAA offers continuous operation and consists of a body, spray 

set-up and plug. 

• VAAN features a manual shut-off needle that enables the flow of 

the liquid to be stopped. 

• VAACO features a clean-out needle that clears the liquid orifice of 

obstructions when activated manually. 

• VAANCO combines the features of the VAAN and VAACO, offering 

a combination shut-off/clean-out needle. 

• VAU offers automatic operation with a built-in shut-off/clean-out 

needle. 

• VAUPM has the same operating features as the VAU, but offers 

the convenience of a mounting plate. 

• VMAU allows for individual adjustment of the atomizing air, fan air 

and liquid flows and offers modular components to accommodate 

a wide range of spray applications. 

• Mounting Kit 28945-001-316SS uses clamps to mount VAA nozzles. 

• Mounting Kit 28945-002-SS uses rods to mount VAA nozzles. 



See Also 







– Strainers 

http:// 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F36


VAU and VMAU Series 

VMAU 

VAA 

VAAN 

VAACO 



VAANCO 

1/8" NPT or BSPT 1/8" NPT or BSPT with 




Mounting Kits 

VAU 



VAUPM 

Clamp mounting kits 

Materials 

Rod mounting kits 

1/8" NPT or BSPT 




Material 

Material 


Nozzle Type 

VMAU VAA VAAN VAACO VAANCO VAU VAUPM 


303 Stainless Steel SS l l l l l l 

303 Stainless Steel/Aluminum SSA l 

316 Stainless Steel l 

Air/Fluid Caps 

303 Stainless Steel SS l l l l l l 

Other materials available upon request. 

Ordering Info 


Nozzle Body* 


1/8 VAA – SS + SUV128 – SS 

l l l l l 

Inlet 


Nozzle 

Body 

Assembly 

Type 

Material 



Set-up 

No. 

Material 



BSPT connections require the addition of a “B” prior to the 

nozzle body inlet connection. 


performance data charts) and material code: VF1650-SS. 


performance data charts) and material code: VA67255-60-SS. 

To order spray nozzle without set-up, use inlet connection, 

nozzle body, and material code: 1/8VAA-SS. 

Order mounting kits separately: 28945-001-316SS. 



SUV128 – SS 

l 

l 


Set-up 

No. 

Material 


To order spray set-up only, 

use spray set-up number and 

material code: SUV128-SS. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F37


VMAU Series 



VMAU 


Set-up 

No. 

SUVM67B 


Set-up 


Fluid and 



Fluid Cap 

VMF1650 

+ 


VMA67255-60 

Press. 

0.7 

1 

1.5 

2 

3 

3.5 

4 

5 

5.5 

Air Capacity* 

Capacity 



l/min 

12.5 

15 

17.5 

23 

29 

36 

42 

48 

55 

Fan 


l/min 

61 

76 

93 

125 

156 

187 

215 

244 

272 

Liquid 

Capacity* 

Press. 

0.2 

0.3 

0.7 

1 

Cap. 

l/h 

2.8 

3.8 

5.3 

6.4 

Atom. 


Press. 

0.7 

1.5 

2 

3 

Water 

Press. 

Spray Coverage (cm) at Indicated Distance from Nozzle 

Fan Air Pressure 


0 0.3 0.7 1.5 2 3 

A B C A B C A B C A B C A B C A B C 

0.2 5.1 7.6 10.2 12.7 15.2 20.3 17.8 22.9 25.4 17.8 22.9 27.9 8.9 10.2 15.2 – – – 

0.7 6.4 8.9 11.4 15.2 20.3 24.1 17.8 22.9 27.9 20.3 25.4 30.5 8.9 10.2 14.0 – – – 

1.5 – – – 15.2 22.9 27.9 20.3 30.5 33 25.4 30.5 35.6 8.9 14.0 17.8 – – – 

0.2 5.1 7.6 11.4 10.2 12.7 15.2 15.2 17.8 20.3 17.8 22.9 27.9 12.7 16.5 17.8 17.8 20.3 25.4 

0.7 5.1 7.6 10.2 10.2 17.8 22.9 17.8 22.9 25.4 20.3 25.4 30.5 11.4 12.7 15.2 17.8 20.3 25.4 

1.5 5.1 7.6 10.2 10.2 17.8 22.9 20.3 25.4 30.5 22.9 30.5 35.6 15.2 19.1 22.9 17.8 20.3 25.4 

0.2 5.1 7.6 11.4 7.6 10.2 12.7 12.7 15.2 17.8 15.2 20.3 25.4 14.0 15.2 17.8 17.8 22.9 27.9 

0.7 5.1 7.6 11.4 10.2 11.4 15.2 15.2 19.1 25.4 17.8 22.9 27.9 14.0 16.5 20.3 17.8 22.9 30.5 

1.5 5.1 7.6 10.2 11.4 15.2 20.3 17.8 22.9 30.5 20.3 25.4 30.5 15.2 17.8 22.9 20.3 22.9 27.9 

0.2 6.4 8.9 15.2 8.9 11.4 17.8 12.7 15.2 20.3 15.2 20.3 25.4 12.7 16.5 20.3 17.8 22.9 27.9 

0.7 5.1 7.6 12.7 10.2 12.7 19.1 12.7 17.8 22.9 17.8 22.9 27.9 15.2 19.1 22.9 17.8 22.9 27.9 

1.5 5.1 7.6 11.4 10.2 14.0 20.3 15.2 20.3 25.4 20.3 22.9 27.9 15.2 19.1 25.4 20.3 25.4 30.5 

6 

61 

301 

1.5 

7.2 

0.2 6.4 8.9 15.2 7.6 11.4 15.2 10.2 12.7 15.2 12.7 17.8 22.9 12.7 16.5 25.4 17.8 22.9 27.9 

4 

0.7 6.4 7.6 12.7 8.9 10.2 16.5 11.4 12.7 17.8 17.8 22.9 27.9 15.2 19.1 27.9 20.3 25.4 30.5 

1.5 5.1 7.6 11.4 8.9 12.7 17.8 12.7 17.8 22.9 17.8 22.9 27.9 15.2 19.1 29.2 20.3 25.4 30.5 

0.2 5.1 7.6 10.2 12.7 15.2 20.3 17.8 22.9 25.4 17.8 22.9 27.9 8.9 10.2 11.4 – – – 

0.7 

0.7 6.4 8.9 11.4 15.2 20.3 24.1 17.8 22.9 27.9 20.3 25.4 30.5 11.4 12.7 15.2 – – – 

0.7 

12.5 

61 

0.2 

4 

1.5 – – – 15.2 22.9 27.9 20.3 30.5 33 25.4 30.5 35.6 17.8 21.6 24.1 – – – 

SUVM67A 

Fluid Cap 

VMF2050 

+ 


VMA67255-60 

1 

1.5 

2 

3 

3.5 

4 

5 

5.5 

15 

17.5 

23 

29 

36 

42 

48 

55 

76 

93 

125 

156 

187 

215 

244 

272 

0.3 

0.7 

1 

5.5 

8 

9.5 

1.5 

2 

3 

0.2 5.1 7.6 11.4 10.2 12.7 15.2 15.2 17.8 20.3 17.8 22.9 27.9 12.7 17.8 21.6 17.8 20.3 25.4 

0.7 5.1 7.6 10.2 12.7 17.8 22.9 17.8 22.9 25.4 20.3 25.4 30.5 15.2 17.8 20.3 17.8 20.3 25.4 

1.5 5.1 7.6 10.2 15.2 17.8 22.9 20.3 25.4 30.5 22.9 30.5 35.6 17.8 20.3 25.4 17.8 20.3 25.4 

0.2 5.1 7.6 11.4 7.6 10.2 12.7 12.7 15.2 17.8 15.2 20.3 25.4 14.0 16.5 17.8 17.8 22.9 27.9 

0.7 5.1 7.6 11.4 10.2 11.4 15.2 15.2 19.1 25.4 17.8 22.9 27.9 17.8 22.9 25.4 17.8 22.9 30.5 

1.5 5.1 7.6 10.2 11.4 15.2 20.3 17.8 22.9 30.5 20.3 25.4 30.5 20.3 25.4 30.5 20.3 22.9 27.9 

0.2 6.4 8.9 15.2 8.9 11.4 17.8 12.7 15.2 20.3 15.2 20.3 25.4 15.2 20.3 22.9 17.8 22.9 27.9 

0.7 5.1 7.6 12.7 10.2 12.7 19.1 12.7 17.8 22.9 17.8 22.9 27.9 15.2 20.3 24.1 17.8 22.9 27.9 

1.5 5.1 7.6 11.4 10.2 14.0 20.3 15.2 20.3 25.4 20.3 22.9 27.9 15.2 21.6 26.7 20.3 25.4 30.5 

6 

61 

301 

1.5 

11 

0.2 6.4 8.9 15.2 7.6 11.4 15.2 10.2 12.7 15.2 12.7 17.8 22.9 16.5 19.1 22.9 17.8 22.9 27.9 

4 

0.7 6.4 7.6 12.7 8.9 10.2 16.5 11.4 12.7 17.8 17.8 22.9 27.9 16.5 22.9 27.9 20.3 25.4 30.5 

1.5 5.1 7.6 11.4 8.9 12.7 17.8 12.7 17.8 22.9 17.8 22.9 27.9 16.5 22.9 30.5 20.3 25.4 30.5 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F38


VMAU Series 


VMAU 



Set-up 

No. 


Set-up 


Fluid and 



Press. 


Capacity 



l/min 

Fan 


l/min 

Liquid 

Capacity* 

Press. 

Cap. 

l/h 

Atom. 


Press. 

Water 

Press. 



0 0.3 0.7 1.5 2 3 


SUVM67 

SUVM113A 

Fluid Cap 

VMF2850 

+ 


VMA67255-60 

Fluid Cap 

VMF3578 

+ 


VMA113289-60 

0.7 

1 

1.5 

2 

3 

3.5 

4 

5 

5.5 

6 

0.7 

1 

1.5 

2 

3 

3.5 

4 

5 

5.5 

6 

12.5 

15 

17.5 

23 

29 

36 

42 

48 

55 

61 

44 

55 

67 

90 

113 

134 

156 

179 

198 

219 

61 

76 

93 

125 

156 

187 

215 

244 

272 

301 

100 

126 

151 

203 

253 

300 

348 

396 

439 

487 

0.2 

0.3 

0.7 

1 

1.5 

0.2 

0.3 

0.7 

1 

1.5 

8 

10.5 

15 

18 

21 

13.5 

17.5 

25 

30 

35 

0.7 

1.5 

2 

3 

4 

0.7 

1.5 

2 

3 

4 

0.2 5.1 7.6 12.7 17.8 22.9 35.6 22.9 30.5 30.5 22.9 25.4 30.5 – – – – – – 

0.7 – – – 21.6 27.9 38.1 30.5 38.1 53.3 38.1 45.7 48.3 – – – – – – 

1.5 – – – – – – 25.4 30.5 40.6 35.6 45.7 58.4 38.1 48.3 58.4 – – – 

0.2 6.4 7.6 11.4 15.2 17.8 22.9 19.1 22.9 27.9 20.3 25.4 33 14.0 16.5 20.3 20.3 22.9 30.5 

0.7 – – – 15.2 20.3 27.9 22.9 27.9 38.1 30.5 38.1 48.3 27.9 30.5 35.6 27.9 30.5 30.5 

1.5 – – – 17.8 22.9 30.5 25.4 30.5 43.2 33 43.2 50.8 35.6 43.2 50.8 43.2 50.8 58.4 

0.2 6.4 7.6 11.4 12.7 15.2 20.3 15.2 20.3 22.9 20.3 25.4 33 12.7 14.0 16.5 17.8 20.3 25.4 

0.7 – – – 12.7 17.8 25.4 20.3 27.9 38.1 27.9 35.6 48.3 22.9 27.9 30.5 22.9 25.4 30.5 

1.5 – – – – – – 20.3 27.9 35.6 27.9 35.6 48.3 30.5 40.6 48.3 40.6 50.8 55.9 

0.2 6.4 8.9 12.7 10.2 12.7 19.1 12.7 17.8 25.4 20.3 22.9 27.9 14.0 16.5 20.3 17.8 22.9 27.9 

0.7 5.1 7.6 11.4 11.4 14.0 20.3 17.8 20.3 27.9 22.9 30.5 40.6 22.9 25.4 29.2 27.9 33 38.1 

1.5 – – – 11.4 15.2 22.9 17.8 22.9 34.3 25.4 30.5 40.6 25.4 31.8 40.6 33 45.7 53.3 

0.2 6.4 8.9 14.0 10.2 11.4 17.8 12.7 15.2 20.3 17.8 22.9 27.9 14.0 16.5 19.1 17.8 22.9 27.9 

0.7 6.4 8.9 14.0 11.4 12.7 19.1 15.2 17.8 24.1 20.3 27.9 33 16.5 22.9 27.9 20.3 25.4 30.5 

1.5 5.1 7.6 11.4 10.2 14.0 20.3 15.2 20.3 25.4 20.3 27.9 35.6 22.9 27.9 38.1 25.4 35.6 40.6 

0.2 – – – 20.3 26.7 35.6 25.4 33 43.2 20.3 25.4 33 – – – – – – 

0.4 – – – 25.4 30.5 40.6 30.5 35.6 45.7 – – – – – – – – – 

0.7 – – – 30.5 35.6 41.9 30.5 16.5 55.9 – – – – – – – – – 

0.2 3.8 5.1 7.6 12.7 17.8 25.4 20.3 27.9 35.6 21.6 30.5 35.6 17.8 21.6 27.9 14.0 17.8 22.9 

0.4 – – – 17.8 22.9 30.5 22.9 30.5 38.1 – – – – – – – – – 

0.7 – – – 17.8 22.9 30.5 26.7 34.3 41.9 – – – – – – – – – 

0.2 5.1 6.4 8.9 10.2 12.7 17.8 15.2 20.3 27.9 20.3 27.9 35.6 20.3 26.7 33 19.1 22.9 27.9 

0.4 – – – 12.7 17.8 25.4 16.5 25.4 33 22.9 30.5 39.4 22.9 27.9 30.5 – – – 

0.7 – – – 11.4 15.2 20.3 16.5 25.4 33 25.4 35.6 40.6 – – – – – – 

0.2 5.1 6.4 10.2 10.2 12.7 15.2 14.0 19.1 27.9 20.3 26.7 35.6 20.3 25.4 33 19.1 21.6 30.5 

0.4 6.4 8.9 14.0 10.2 12.7 19.1 15.2 20.3 25.4 22.9 29.2 40.6 20.3 27.9 35.6 20.3 21.6 30.5 

0.7 5.1 7.6 10.2 11.4 15.2 21.6 16.5 22.9 30.5 25.4 35.6 47 25.4 34.3 45.7 21.6 26.7 36.8 

0.2 5.1 6.4 7.6 5.1 10.2 12.7 12.7 16.5 20.3 20.3 25.4 30.5 19.1 24.1 35.6 19.1 24.1 30.5 

0.4 6.4 7.6 11.4 10.2 11.4 15.2 14.0 17.8 24.1 20.3 25.4 33 25.4 30.5 38.1 22.9 30.5 38.1 

0.7 6.4 7.6 12.7 10.2 11.4 19.1 14.0 19.1 24.1 21.6 27.9 25.4 25.4 31.8 45.7 22.9 30.5 38.1 



SUVM113 

Fluid Cap 

VMF4078 

+ 


VMA113289-60 

0.7 

1 

1.5 

2 

3 

3.5 

4 

5 

5.5 

6 

44 

55 

67 

90 

113 

134 

156 

179 

198 

219 

100 

126 

151 

203 

253 

300 

348 

396 

439 

487 

0.2 

0.3 

0.7 

1 

1.5 

18 

24 

34 

42 

48 

0.7 

1.5 

2 

3 

4 

0.2 5.1 6.4 10.2 17.8 19.1 43.2 27.9 38.1 45.7 25.4 34.3 38.1 – – – – – – 

0.4 – – – 20.3 29.2 43.2 30.5 43.2 55.9 – – – – – – – – – 

0.7 – – – 22.9 33 45.7 30.5 43.2 58.4 – – – – – – – – – 

0.2 5.1 7.6 12.7 16.5 22.9 27.9 22.9 33 45.7 25.4 33 41.9 – – – – – – 

0.4 5.1 10.2 12.7 17.8 22.9 30.5 24.1 30.5 43.2 35.6 38.1 47 – – – – – – 

0.7 – – – 16.5 26.7 35.6 27.9 35.6 47 40.6 48.3 50.8 – – – – – – 

0.2 5.1 6.4 10.2 12.7 17.8 27.9 17.8 27.9 34.3 22.9 30.5 43.2 20.3 27.9 33 – – – 

0.4 3.8 6.4 7.6 12.7 19.1 25.4 20.3 25.4 36.8 27.9 34.3 40.6 25.4 30.5 39.4 19.1 25.4 35.6 

0.7 – – – 14.0 20.3 27.9 20.3 26.7 35.6 29.2 38.1 52.1 30.5 38.1 45.7 24.1 30.5 43.2 

0.2 3.8 6.4 11.4 10.2 15.2 20.3 16.5 21.6 30.5 22.9 30.5 40.6 21.6 29.2 38.1 21.6 27.9 36.8 

0.4 3.8 6.4 10.2 11.4 15.2 20.3 17.8 22.9 31.9 25.4 33 43.2 26.7 30.5 40.6 21.6 27.9 38.1 

0.7 5.1 7.6 20.3 11.4 16.5 19.1 17.8 25.4 36.8 25.4 35.6 48.3 27.9 33 43.2 25.4 30.5 48.3 

0.2 5.1 7.6 10.2 8.9 12.7 17.8 15.2 19.1 25.4 20.3 27.9 35.6 22.9 27.9 38.1 22.9 26.7 35.6 

0.4 5.1 7.6 10.2 12.7 19.1 15.2 20.3 26.7 30.5 22.9 31.8 39.4 22.9 31.8 45.7 24.1 29.2 41.9 

0.7 5.1 7.6 10.2 8.9 12.7 20.3 15.2 20.3 33 21.6 29.2 41.9 24.1 33 40.6 24.1 31.8 41.9 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F39


VMAU Series 



VMAU 


Set-up 

No. 

SUVM128 

SUVM152 


Set-up 


Fluid and 



Fluid Cap 

VMF60100 

+ 


VMA1282100-60 

Fluid Cap 

VMF80125 

+ 


VMA1522110-60 

Press. 

0.7 

1 

1.5 

2 

3 

3.5 

4 

5 

5.5 

6 

0.7 

1 

1.5 

2 

3 

3.5 

4 

5 

5.5 

6 


Capacity 



l/min 

46 

56 

67 

88 

110 

132 

153 

176 

198 

221 

50 

62 

75 

101 

125 

150 

174 

198 

221 

244 

Fan 


l/min 

110 

139 

168 

229 

289 

348 

405 

462 

515 

566 

109 

136 

165 

221 

277 

331 

385 

436 

487 

532 

Liquid 

Capacity* 

Press. 

0.2 

0.3 

0.7 

1 

1.5 

0.2 

0.3 

0.7 

1 

1.5 

Cap. 

l/h 

38 

49 

70 

86 

99 

69 

89 

126 

155 

179 

Atom. 


Press. 

0.7 

1.5 

2 

3 

4 

0.7 

1.5 

2 

3 

4 

Water 

Press. 




0 0.3 0.7 1 1.5 2 


0.1 – – – 25.4 34.3 53.3 33 40.6 55.9 30.5 40.6 53.3 – – – – – – 

0.2 – – – 24.1 31.8 48.3 35.6 45.7 61 31.8 43.2 61 30.5 40.6 50.8 – – – 

0.4 – – – 25.4 33 50.8 35.6 48.3 66 40.6 55.9 76.2 45.7 62.2 86.4 48.3 61 83.8 

0.1 – – – 15.2 21.6 33 20.3 27.9 44.5 24.1 33 44.5 20.3 30.5 35.6 20.3 26.7 30.5 

0.2 – – – 17.8 25.4 36.8 22.9 31.8 45.7 25.4 35.6 50.8 24.1 33 47 25.4 33 40.6 

0.4 – – – 19.1 26.7 36.8 25.4 35.6 49.5 30.5 44.5 61 27.9 44.5 66 30.5 45.7 68.6 

0.1 3.8 7.6 11.4 12.7 17.8 24.1 17.8 25.4 35.6 22.9 27.9 35.6 25.4 35.6 43.2 24.1 30.5 40.6 

0.2 5.1 7.6 12.7 14.0 20.3 34.3 20.3 27.9 38.1 24.1 33 48.3 25.4 35.6 48.3 25.4 33 41.9 

0.4 2.5 7.6 12.7 11.4 15.2 24.1 20.3 27.9 40.6 24.1 33 48.3 25.4 36.8 54.6 30.5 40.6 55.9 

0.1 5.1 7.6 14.0 12.7 15.2 22.9 15.2 22.9 33 20.3 27.9 39.4 21.6 29.2 36.8 22.9 33 43.2 

0.2 6.4 7.6 14.0 12.7 17.8 25.4 16.5 24.1 35.6 20.3 30.5 45.7 25.4 33 48.3 25.4 34.3 48.3 

0.4 5.1 7.6 10.2 12.7 17.8 25.4 15.2 25.4 38.1 22.9 33 45.7 25.4 35.6 50.8 27.9 36.8 55.9 

0.1 7.6 10.2 15.2 11.4 15.2 22.9 14.0 20.3 30.5 16.5 25.4 35.6 21.6 22.9 36.8 21.6 30.5 40.6 

0.2 7.6 10.2 15.2 11.4 16.5 24.1 15.2 21.6 30.5 17.8 25.4 35.6 22.9 27.9 40.6 22.9 30.5 41.9 

0.4 6.4 8.9 10.2 10.2 14.0 19.1 12.7 17.8 27.9 16.5 22.9 34.3 20.3 27.9 43.2 22.9 30.5 45.7 

0.1 – – – 26.7 33 53.3 33 43.2 66 33 48.3 68.6 33 45.7 61 25.4 38.1 54.6 

0.2 – – – – – – 33 44.5 66 30.5 53.3 73.7 33 49.5 76.2 38.1 58.4 76.2 

0.4 – – – – – – 35.6 48.3 67.3 41.9 53.3 71.1 40.6 61 86.4 – – – 

0.1 – – – 15.2 20.3 33 24.1 33 47 25.4 38.1 55.9 20.3 30.5 35.6 22.9 35.6 53.3 

0.2 – – – 17.8 24.1 38.1 25.4 35.6 50.8 27.9 39.4 52.1 24.1 33 47 31.8 33 63.5 

0.4 – – – – – – 25.4 34.3 53.3 30.5 44.5 66 27.9 44.5 66 38.1 53.3 81.3 

0.1 6.4 7.6 10.2 15.2 20.3 30.5 19.1 27.9 43.2 25.4 34.3 49.5 25.4 35.6 43.2 22.9 35.6 49.5 

0.2 – – – 12.7 17.8 26.7 20.3 30.5 48.3 26.7 34.3 50.8 25.4 35.6 48.3 30.5 41.9 57.2 

0.4 – – – – – – 21.6 27.9 40.6 27.9 35.6 50.8 25.4 36.8 54.6 30.5 40.6 61 

0.1 5.1 7.6 7.6 10.2 12.7 15.2 15.2 20.3 30.5 20.3 30.5 41.9 21.6 29.2 36.8 22.9 33 45.7 

0.2 – – – 12.7 19.1 25.4 17.8 25.4 38.1 21.6 31.8 45.7 25.4 33 48.3 25.4 38.1 53.3 

0.4 – – – – – 25.4 17.8 25.4 35.6 21.6 30.5 43.2 25.4 35.6 50.8 27.9 40.6 58.4 

0.1 3.8 5.1 7.6 7.6 12.7 16.5 16.5 19.1 26.7 20.3 25.4 35.6 21.6 22.9 36.9 20.3 30.5 45.7 

0.2 5.1 7.6 12.7 12.7 12.7 19.1 15.2 21.6 30.5 17.8 25.4 36.8 22.9 27.9 40.6 25.4 33 47 

0.4 – – – – – – 15.2 17.8 30.5 17.8 25.4 35.6 20.3 27.9 43.2 25.4 35.6 48.3 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F40


VAU Series 



Fan air 

Atomized liquid 

Fan air 

External mix with fan air: 

flat spray pattern 

Without fan air: 

round spray pattern. 


• The dimensions “A”, “B” and “C” of the flat spray pattern are controlled by the combination of fan 

air pressure and atomizing air pressure. 

• The liquid flow rate is constant and not affected by the air pressure. 

Flat spray 

pattern 

D 

C 

B 

A 

6" 

(15 cm) 

9" (23 cm) 

15" (38 cm) 

28207-101-SS cap ring and 

29154-001-BUC must be 

ordered separately from 

the spray set-up, but are 

included in the standard nozzle 

assembly. Please contact your 

sales engineer. 

VAU 


Set-up 

No. 

SUV67B 

SUV67A 

SUV67 


Set-up 


Fluid and 



Fluid Cap 

VF1650 

+ 


VA67255-60 

Fluid Cap 

VF2050 

+ 


VA67255-60 

Fluid Cap 

VF2850 

+ 


VA67255-60 

Press. 

.69 

1.0 

1.4 

2.1 

2.8 

3.4 

4.1 

4.8 

5.5 

6.2 

.69 

1.0 

1.4 

2.1 

2.8 

3.4 

4.1 

4.8 

5.5 

6.2 

.69 

1.0 

1.4 

2.1 

2.8 

3.4 

4.1 

4.8 

5.5 

6.2 

Air Capacity*† 



l/min 

12.5 

15.0 

17.6 

23 

29 

36 

42 

48 

55 

61 

12.5 

15.0 

17.6 

23 

29 

36 

42 

48 

55 

61 

12.5 

15.0 

17.6 

23 

29 

36 

42 

48 

55 

61 

Fan Air 

l/min 

61 

76 

93 

125 

156 

187 

215 

244 

272 

301 

61 

76 

93 

125 

156 

187 

215 

244 

272 

301 

61 

76 

93 

125 

156 

187 

215 

244 

272 

301 

Liquid Capacity*† 

Press. 

.21 

.21 

.34 

.34 

.69 

.69 

1.0 

1.0 

1.4 

1.4 

.21 

.21 

.34 

.34 

.69 

.69 

1.0 

1.0 

1.4 

1.4 

.21 

.21 

.34 

.34 

.69 

.69 

1.0 

1.0 

1.4 

1.4 

Cap. 

l/h 

2.8 

2.8 

3.6 

3.6 

5.1 

5.1 

6.3 

6.3 

7.3 

7.3 

4.2 

4.2 

5.5 

5.5 

7.8 

7.8 

9.5 

9.5 

11.1 

11.1 

8.1 

8.1 

10.5 

10.5 

15.0 

15.0 

18.4 

18.4 

21 

21 

Atom. 


Press. 

1.5 

2 

3 

6 

1.5 

2 

3 

6 

1.5 

2 

3 

6 


Spray Coverage (centimeters) at Indicated Distance from Nozzle 

†Since the pressures of the air and liquid lines are independently controlled, any combination of these air and liquid pressures can be used. The total 

air capacity is the sum of the atomizing air l/min and the fan air l/min. For instance, for atomizing air at 1 bar and fan air at 2.1 bar, the total is equal to 

15 l/min + 125 l/min for a total of 140 l/min. 

††At 0 bar fan air pressure the spray forms a round spray pattern. Request Data Sheets 37459M-V67B, 37459M-V67A and 37459M-V67. 

Spray set-ups are interchangeable, but each set-up uses a different needle size. 

Water 

Press. 


0†† 0.3 0.7 1.5 

A B C A B C A B C A B C 

.20 5.1 7.6 11.4 10.2 12.7 15.2 15.2 17.8 20 17.8 23 28 

.70 5.1 6.4 10.2 12.7 17.8 25 17.8 22 30 20 25 36 

1.5 5.1 7.6 10.2 15.2 20 30 20 28 36 25 30 43 

.20 5.1 7.6 11.4 7.6 10.2 12.7 12.7 15.2 17.8 17.8 23 29 

.70 5.1 6.4 11.4 10.2 11.4 15.2 15.2 19.1 25 19.1 25 36 

1.5 5.1 7.6 10.2 11.4 15.2 20 17.8 23 33 23 30 41 

.20 6.4 8.9 15.2 8.9 11.4 17.8 12.7 15.2 20 17.8 23 28 

.70 5.1 7.6 12.7 10.2 12.7 19.1 15.2 17.8 25 19.1 23 23 

1.5 5.1 7.6 11.4 10.2 14.0 20 15.2 20 30 23 28 36 

.20 5.1 7.6 12.7 7.6 10.2 14.0 10.2 12.7 15.2 15.2 17.8 23 

.70 6.4 7.6 12.7 7.6 10.2 15.2 10.2 12.7 17.8 15.2 20 28 

1.5 5.1 7.6 11.4 7.6 11.4 16.5 10.2 15.2 20 17.8 23 30 

.20 5.1 7.6 11.4 12.7 15.2 19.1 15.2 17.8 20 19.1 24 30 

.70 5.1 7.6 11.4 12.7 17.8 25 20 25 36 23 30 41 

1.5 5.1 7.6 10.2 15.2 20 30 23 28 38 25 33 43 

.20 5.1 7.6 11.4 10.2 12.7 16.5 14.0 17.8 20 16.5 22 27 

.70 5.1 7.6 12.7 10.2 15.2 20 17.8 23 30 23 30 41 

1.5 5.1 7.6 10.2 12.7 15.2 23 17.8 25 33 25 33 46 

.20 6.4 8.9 14.0 8.9 12.7 17.8 12.7 16.5 23 19.1 23 28 

.70 5.1 7.6 12.7 10.2 14.0 20 16.5 19.1 16.5 20 25 38 

1.5 5.1 7.6 11.4 10.2 15.2 22 16.5 22 32 24 30 39 

.20 6.4 8.9 12.7 7.6 11.4 15.2 10.2 14.0 16.5 17.8 23 30 

.70 6.4 8.9 12.7 8.9 11.4 16.5 11.4 15.2 20 20 25 36 

1.5 5.1 7.6 11.4 8.9 11.4 16.5 11.4 16.5 22 20 28 36 

.20 6.4 7.6 11.4 15.2 17.8 23 19.1 23 28 20 25 33 

.70 5.1 7.6 12.7 15.2 20 28 23 28 38 30 38 48 

1.5 5.1 6.4 10.2 17.8 23 30 25 30 43 33 43 51 

.20 6.4 7.6 11.4 12.7 15.2 20 15.2 20 23 20 25 33 

.70 5.1 7.6 12.7 12.7 17.8 25 20 28 38 28 36 48 

1.5 5.1 6.4 10.2 12.7 17.8 25 20 28 36 28 36 48 

.20 6.4 8.9 12.7 10.2 12.7 19.1 12.7 17.8 25 20 23 28 

.70 5.1 7.6 12.7 11.4 14.0 20 17.8 20 28 23 30 41 

1.5 5.1 7.6 12.7 11.4 15.2 23 17.8 23 34 25 33 43 

.20 6.4 8.9 12.7 8.9 12.7 15.2 11.4 15.2 17.8 15.2 20 28 

.70 6.4 8.9 12.7 10.2 14.0 17.8 12.7 17.8 23 17.8 23 33 

1.5 6.4 7.6 11.4 8.9 12.7 16.5 12.7 17.8 23 17.8 25 36 



Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F41


VAU Series 



VAU 


Set-up 

No. 

SUV113A 

SUV113 

SUV128 

SUV152 


Set-up 


Fluid and 



Fluid Cap 

VF3578 

+ 


VA113293-60 

Fluid Cap 

VF4078 

+ 


VA113293-60 

Fluid Cap 

VF60100 

+ 


VA1282125-60 

Fluid Cap 

VF80125 

+ 


VA1522125-60 

Press. 

.69 

1.0 

1.4 

2.1 

2.8 

3.4 

4.1 

4.8 

5.5 

6.2 

.69 

1.0 

1.4 

2.1 

2.8 

3.4 

4.1 

4.8 

5.5 

6.2 

.69 

1.0 

1.4 

2.1 

2.8 

3.4 

4.1 

4.8 

5.5 

6.2 

.69 

1.0 

1.4 

2.1 

2.8 

3.4 

4.1 

4.8 

5.5 

6.2 

Air Capacity*† 



l/min 

44 

55 

67 

90 

113 

134 

156 

179 

198 

219 

44 

55 

67 

90 

113 

134 

156 

179 

198 

219 

46 

56 

67 

88 

110 

132 

153 

176 

198 

221 

50 

62 

75 

101 

125 

150 

174 

198 

221 

244 

Fan Air 

l/min 

100 

126 

151 

203 

253 

300 

348 

396 

439 

487 

100 

126 

151 

203 

253 

300 

348 

396 

439 

487 

110 

139 

168 

229 

289 

348 

405 

462 

515 

566 

109 

136 

165 

221 

277 

331 

385 

436 

487 

532 

Liquid Capacity*† 

Press. 

.21 

.21 

.34 

.34 

.69 

.69 

1.0 

1.0 

1.4 

1.4 

.21 

.21 

.34 

.34 

.69 

.69 

1.0 

1.0 

1.4 

1.4 

.21 

.21 

.34 

.34 

.69 

.69 

1.0 

1.0 

1.4 

1.4 

.21 

.21 

.34 

.34 

.69 

.69 

1.0 

1.0 

1.4 

1.4 

Cap. 

l/h 

13.6 

13.6 

17.6 

17.6 

25 

25 

30 

30 

35 

35 

18.4 

18.4 

24 

24 

34 

34 

42 

42 

48 

48 

38 

38 

49 

49 

70 

70 

86 

86 

99 

99 

69 

69 

89 

89 

126 

126 

155 

155 

179 

179 

Atom. 


Press. 

1.5 

2 

3 

6 

1.5 

2 

3 

6 

1.5 

2 

3 

6 

1.5 

2 

3 

6 

Water 

Press. 


Spray Coverage (centimeters) at Indicated Distance from Nozzle 


0†† 0.3 0.7 1.5 

A B C A B C A B C A B C 

.20 6.4 7.6 12.7 8.9 11.4 15.2 15.2 17.8 23 25 33 41 

.70 6.4 8.9 12.7 8.9 11.4 17.8 15.2 23 30 28 38 51 

1.5 5.1 7.6 12.7 8.9 11.4 20 15.2 20 28 28 38 53 

.20 6.4 7.6 12.7 7.6 10.2 14.0 10.2 12.7 17.8 17.8 23 30 

.70 6.4 8.9 12.7 8.9 11.4 15.2 12.7 17.8 23 20 28 38 

1.5 6.4 8.9 14.0 7.6 12.7 17.8 10.2 15.2 23 20 30 41 

.20 6.4 7.6 12.7 7.6 10.2 15.2 8.9 11.4 16.5 15.2 20 25 

.70 6.4 8.9 12.7 8.9 10.2 15.2 10.2 12.7 16.5 15.2 23 30 

1.5 6.4 8.9 12.7 8.9 11.4 16.5 10.2 14.0 20 17.8 25 36 

.20 6.4 8.9 12.7 6.4 8.9 12.7 6.4 8.9 12.7 10.2 12.7 15.2 

.70 6.4 8.9 12.7 6.4 10.2 14.0 7.6 10.2 15.2 10.2 15.2 20 

1.5 6.4 8.9 12.7 7.6 10.2 15.2 7.6 10.2 16.5 11.4 15.2 23 

.20 6.4 8.9 15.2 7.6 11.4 15.2 15.2 20 25 25 36 46 

.70 6.4 8.9 12.7 10.2 12.7 17.8 17.8 23 30 28 38 53 

1.5 5.1 7.6 12.7 8.9 11.4 16.5 15.2 23 30 28 38 48 

.20 6.4 8.9 15.2 7.6 10.2 15.2 10.2 15.2 20 20 28 36 

.70 6.4 8.9 12.7 7.6 10.2 15.2 11.4 15.2 20 23 28 43 

1.5 5.1 7.6 12.7 7.6 11.4 15.2 11.4 15.2 23 23 30 43 

.20 6.4 8.9 15.2 7.6 10.2 16.5 8.9 12.7 17.8 16.5 23 28 

.70 6.4 8.9 14.0 7.6 11.4 17.8 10.2 15.2 20 17.8 25 33 

1.5 6.4 8.9 14.0 7.6 10.2 17.8 8.9 12.7 20 17.8 25 33 

.20 6.4 8.9 15.2 6.4 8.9 15.2 6.4 10.2 15.2 10.2 12.7 19.1 

.70 5.1 7.6 12.7 6.4 7.6 14.0 6.4 8.9 14.0 10.2 15.2 20 

1.5 5.1 7.6 15.2 6.4 8.9 15.2 7.6 10.2 15.2 11.4 15.2 19.1 

.20 7.6 10.2 12.7 7.6 10.2 15.2 12.7 17.8 23 23 30 41 

.70 – – – 7.6 12.7 15.2 12.7 17.8 25 20 30 41 

1.5 – – – – – – – – – – – – 

.20 7.6 10.2 12.7 8.9 11.4 16.5 10.2 15.2 20 15.2 20 28 

.70 6.4 8.9 12.7 7.6 10.2 14.0 10.2 15.2 22 17.8 23 38 

1.5 – – – – – – – – – – – – 

.20 7.6 10.2 14.0 7.6 11.4 15.2 8.9 12.7 17.8 15.2 20 28 

.70 6.4 8.9 12.7 8.9 11.4 15.2 10.2 12.7 17.8 15.2 20 27 

1.5 6.4 8.9 12.7 7.6 10.2 16.5 7.6 12.7 20 15.2 20 28 

.20 7.6 10.2 15.2 7.6 10.2 15.2 7.6 10.2 15.2 10.2 12.7 17.8 

.70 7.6 10.2 15.2 7.6 10.2 15.2 7.6 10.2 15.2 10.2 15.2 20 

1.5 7.6 10.2 14.0 7.6 10.2 15.2 7.6 10.2 15.2 10.2 15.2 20 

.20 7.6 10.2 12.7 11.4 15.2 22 15.2 20 28 25 30 43 

.70 – – – – – – – – – 25 36 43 

1.5 – – – – – – – – – – – – 

.20 7.6 10.2 12.7 8.9 12.7 17.8 12.7 16.5 23 20 28 38 

.70 – – – – – – 12.7 17.8 23 20 28 38 

1.5 – – – – – – – – – – – – 

.20 7.6 10.2 14.0 10.2 12.7 17.8 12.7 15.2 23 17.8 23 30 

.70 7.6 8.9 12.7 8.9 11.4 15.2 11.4 14.0 19.1 15.2 23 30 

1.5 – – – – – – – – – – – – 

.20 7.6 10.2 15.2 8.9 11.4 16.5 10.2 12.7 17.8 12.7 15.2 23 

.70 8.9 10.2 14.0 8.9 11.4 16.5 8.9 12.7 19.1 12.7 15.2 23 

1.5 6.4 8.9 11.4 7.6 10.2 15.2 8.9 11.4 17.8 10.2 15.2 20 

†Since the pressures of the air and liquid lines are independently controlled, any combination of these air and liquid pressures can be used. The total 

air capacity is the sum of the atomizing air l/min and the fan air l/min. For instance, for atomizing air at 1 bar and fan air at 2.1 bar, the total is equal to 

15 l/min + 125 l/min for a total of 140 l/min. 

††At 0 bar fan air pressure the spray forms a round spray pattern. Request Data Sheets 37459M-V113A, 37459M-V113, 37459M-V128 and 37459M-V152. 

Spray set-ups are interchangeable, but each set-up uses a different needle size. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F42


1/2J Series 

1/2J 

1/2J Series air atomizing nozzles 

1/2J 

Plug CP1706 


1/2JN 


1/2JN 

1/2JCO 

1 2 3 4 

5 



3. Fluid cap 

4. Fluid cap gasket CP8491 


Shut-off 


Clean-out needle 

assembly 11829 


with shut-off needle 

1/2JCO 


with clean-out needle 


• 1/2J air atomizing series ranges in capacity from 4.1 to 306 gph (15.5 to 1158 l/h). 

• The nozzles are available with shut-off and clean-out needles. 

• 1/2J body has liquid and air feeds at opposite ends of the body and is provided with a removable 

plug so other needle assemblies may be added in the future. 

• 1/2JN features a manual shut-off needle that enables the flow of liquid to be stopped. 

• 1/2JCO features a clean-out needle that is activated manually. 

– The needle slides through the liquid orifice to clear obstructions. 

– Ideal for intermittent spraying applications when liquid can dry in the orifice between uses. 





See Also 

http:// 







– Strainers 

Materials 

Ordering Info 

Nozzle Bodies 

Material 

Material 


Nozzle Type 

J JN JCO 

Nickel-plated Brass (none) l l l 



Nickel-plated Brass Air Cap and 

303 Stainless Steel Fluid Cap 

SSBR l l l 



Nozzle Body* 


1/2 JN – SS + SU77 – SS 

l l l l l 

Inlet 


Nozzle 

Body 

Assembly 

Type 

Material 



Set-up 

No. 

Material 



BSPT connections require the addition of a “B” prior 

to the nozzle body inlet connection. 




performance data charts) and material code: 422-6-73-70°. 



SU77 – SS 

l l 


Set-up 

No. 

Material 




and material code: 

SU77-SS. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F43

Nozzle Bodies/Nozzle Assemblies, 1/2J Series 



• JBC features the center lines of the air and liquid inlet entering 

in the back of the nozzle and parallel to the spray projection axis. 

• 1/2JBCJ features a steam jacket around the nozzle body 

for spraying liquids that are too viscous to spray at room 

temperature. 

• 2J is a dual spray assembly with opposing spray set-ups 

perpendicular to opposing air and liquid inlets. 

• Thick wall adapters replace retainer rings on nozzle assemblies 

and fit into threaded wall openings holding the nozzle securely 

in place. 



See Also 







• For JBC, request Data Sheets 4921, 6885 and 6185 

• For 1/2JBCJ, request Data Sheets 4610 and 6331 

• For 2J, request Data Sheets 5356 and 6530 

• For thick wall adapters, request Data Sheets 3378, 

7003 and 7323 

http:// 

Back Connect 

Steam Jacket 

Twin Spray 

Thick Walls 




steam inlet/outlet connection 


air and liquid inlet connection 



Please refer to data sheets 

1/2JBC air atomizing nozzle 

1/2JBC air atomizing nozzle used to spray 

seasoned cooking oil onto corn snacks. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F44


1/2J Series 



• For wide angle round, round, 360° circular and flat sprays, dimensions “A”, “B” and “C” are the 

pattern widths at distances from the nozzle. 





Wide angle round, round, flat 

and 360° circular spray air 

caps produce wide angle round 

hollow cone spray, round hollow 

cone spray, flat spray and 360° 

circular spray patterns. 


D 

8491 gasket must be ordered separately from the spray set-up, but is included in the 

standard nozzle assembly. Please contact your sales engineer. 

C 

B 

A 

9" 

(23 cm) 

18" (46 cm) 

27" (69 cm) 


Fluid cap 


8491 

gasket 





Set-up 

No. 

SU75 

SU85 


Set-up 


Fluid and 



Fluid Cap 

250375 

+ 


4533102 

Fluid Cap 

251376 

+ 


4693102 


Pattern 

Flat 

Flat 


Press. 




0.35 1 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

– – – 1.8 154 590 3.4 184 950 – – – – – – 

– – – 2.0 119 640 3.5 157 1010 – – – – – – 

– – – 2.1 93 690 3.7 133 1060 – – – – – – 

– – – – – – 3.8 112 1110 – – – – – – 

l/h 


l/min 

.70 134 315 1.3 320 440 2.1 575 570 3.0 740 710 3.9 840 860 

.85 100 380 1.4 255 520 2.2 505 640 3.1 690 770 4.1 790 930 

– – – 1.5 200 590 2.4 440 720 3.2 630 840 4.2 740 990 

– – – 1.7 154 670 2.5 380 790 3.4 570 910 4.4 690 1070 

– – – – – – 2.7 330 860 3.5 520 980 4.5 650 1140 

– – – – – – 2.8 275 930 3.7 470 1050 4.6 600 1210 

– – – – – – 3.0 235 1010 3.8 420 1120 4.8 550 1280 

– – – – – – 3.1 195 1080 3.9 345 1190 4.9 510 1350 

– – – – – – – – – 4.1 325 1260 5.1 465 1430 

– – – – – – – – – – – – 5.2 425 1490 

– – – – – – – – – – – – 5.3 390 1560 

– – – – – – – – – – – – 5.5 350 1640 


2.0 

3.5 

.70 

1.4 

2.5 

3.4 

4.5 

Liquid* 

1.0 

2.0 

.35 

1.0 

2.0 

3.0 

4.0 


Dimensions 

A 

(cm) 

46 

51 

51 

86 

86 

91 

91 

B 

(cm) 

76 

79 

86 

157 

157 

168 

170 

C 

(cm) 

91 

97 

119 

211 

208 

216 

226 

D 

(m) 

5.8 

7.0 

4.0 

4.6 

5.2 

5.8 

6.4 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F45


1/2J Series 



Wide Angle Round and Round Spray 


Set-up 

No. 

SU77 

SU78 


Set-up 


Fluid and 



Fluid Cap 

250375 

+ 


422-6-73-70° 

Fluid Cap 

250375 

+ 


422-6-94-70° 


Pattern 

Wide 

Angle 

Round 

Wide 

Angle 

Round 


Press. 




0.35 1 2 3 4 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

– – – – – – 2.1 213 176 3.1 316 214 4.2 238 351 

– – – – – – 2.3 127 249 3.2 195 292 4.3 154 439 

– – – – – – – – – 3.4 107 371 4.5 100 521 

.60 102 184 1.1 215 153 2.5 185 355 3.7 192 560 5.0 230 830 

.70 57 230 1.3 124 230 2.7 146 410 3.9 150 620 5.3 158 940 

.85 32 280 1.4 84 280 2.8 112 465 4.0 119 680 5.6 108 1080 

– – – – – – 3.0 86 520 4.2 86 770 – – – 

– – – – – – 3.1 65 580 4.6 51 910 – – – 


2.1 

3.2 

4.3 

.70 

1.3 

2.8 

4.0 

5.3 

Liquid* 

2.0 

3.0 

4.0 

.35 

1.0 

2.0 

3.0 

4.0 


Dimensions 

A 

(cm) 

36 

36 

36 

33 

34 

33 

34 

36 

B 

(cm) 

48 

48 

48 

47 

48 

47 

48 

48 

C 

(cm) 

69 

69 

69 

65 

67 

65 

67 

69 

D 

(m) 

6.7 

7.3 

8.5 

6.1 

7.9 

6.4 

7.3 

8.2 

SU79 

Fluid Cap 

250375 

+ 


469-6-125- 

70° 

Wide 

Angle 

Round 

.70 129 325 1.7 182 540 3.1 265 810 4.3 350 1000 – – – 

.85 82 380 1.8 143 590 3.2 245 860 4.6 260 1080 – – – 

1.0 45 415 – – – 3.4 173 910 5.0 186 1200 – – – 

– – – – – – 3.5 136 950 – – – – – – 

– – – – – – 3.6 120 980 – – – – – – 

.85 

1.7 

3.4 

4.6 

.35 

1.0 

2.0 

3.0 

36 

33 

33 

36 

50 

48 

47 

50 

69 

66 

66 

69 

7.9 

7.3 

7.0 

8.5 

SU89 

Fluid Cap 

251376 

+ 


469-6-130- 

70° 

Wide 

Angle 

Round 

.70 134 315 1.3 320 440 2.1 575 570 3.0 740 710 3.9 840 860 

.85 100 380 1.4 255 520 2.2 505 640 3.1 690 770 4.1 790 930 

– – – 1.5 200 590 2.4 440 720 3.2 630 840 4.2 740 990 

– – – 1.7 154 670 2.5 380 790 3.4 570 910 4.4 690 1070 

– – – – – – 2.7 330 860 3.5 520 980 4.5 650 1140 

– – – – – – 2.8 275 930 3.7 470 1050 4.6 600 1210 

– – – – – – 3.0 235 1010 3.8 420 1120 4.8 550 1280 

– – – – – – 3.1 195 1080 3.9 345 1190 4.9 510 1350 

– – – – – – – – – 4.1 325 1260 5.1 465 1430 

– – – – – – – – – – – – 5.2 425 1490 

– – – – – – – – – – – – 5.3 390 1560 

– – – – – – – – – – – – 5.5 350 1640 

.70 

1.4 

2.5 

3.4 

4.5 

.35 

1.0 

2.0 

3.0 

4.0 

33 

33 

28 

28 

28 

64 

66 

56 

53 

56 

91 

91 

81 

74 

79 

3.4 

4.9 

6.1 

6.7 

7.6 

SU72 

Fluid Cap 

250375 

+ 

4221250 

Round 

1.3 34 350 1.7 146 365 3.0 230 510 – – – – – – 

1.4 25 390 1.8 121 395 3.1 200 550 – – – – – – 

1.5 20 415 2.0 102 430 3.2 176 590 – – – – – – 

1.7 15.5 445 2.1 86 460 3.4 154 620 – – – – – – 

– – – 2.3 72 490 3.5 135 660 – – – – – – 

– – – 2.4 60 520 3.6 118 700 – – – – – – 

1.4 

2.0 

3.2 

.35 

1.0 

2.0 

9 

9 

9 

16 

16 

16 

25 

25 

25 

6.7 

7.3 

8.2 

SU82 

Fluid Cap 

251376 

+ 


4691312 

Round 

.70 134 315 1.3 320 440 2.1 575 570 3.0 740 710 3.9 840 860 

.85 100 380 1.4 255 520 2.2 505 640 3.1 690 770 4.1 790 930 

– – – 1.5 200 590 2.4 440 720 3.2 630 840 4.2 740 990 

– – – 1.7 154 670 2.5 380 790 3.4 570 910 4.4 690 1070 

– – – – – – 2.7 330 860 3.5 520 980 4.5 650 1140 

– – – – – – 2.8 275 930 3.7 470 1050 4.6 600 1210 

– – – – – – 3.0 235 1010 3.8 420 1120 4.8 550 1280 

– – – – – – 3.1 195 1080 3.9 345 1190 4.9 510 1350 

– – – – – – – – – 4.1 325 1260 5.1 465 1430 

– – – – – – – – – – – – 5.2 425 1490 

– – – – – – – – – – – – 5.3 390 1560 

– – – – – – – – – – – – 5.5 350 1640 

.70 

1.4 

2.5 

3.4 

4.5 

.35 

1.0 

2.0 

3.0 

4.0 

10 

15 

13 

10 

10 

18 

25 

20 

18 

18 

23 

33 

25 

25 

25 

7.0 

6.4 

11.3 

12.5 

14.3 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F46


1/2J Series 


Flat spray air caps produce 

a flat spray pattern. 


• The dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle. 

• The total distance of spray projection from the nozzle to the maximum dispersal point is represented 

by “D”. 

• SUE75 and SU380C are pressure set-ups using pressurized liquids. 

• In SU380C, the air and liquid mix internally, while in SUE75, they mix externally. 

• SU70 is a siphon set-up with the air and siphoned liquid mixing externally. 

C 

B 

A 


Fluid cap 

Flat spray 

pattern 


D 

9" 

(23 cm) 

18" (46 cm) 

27" (69 cm) 


8491 

gasket 








Set-up 

No. 


Set-up 


Fluid and 




Press. 



0.2 0.35 0.5 0.7 1 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Liquid* 


Dimensions 

A 

(cm) 

B 

(cm) 

C 

(cm) 

D 

(m) 

SUE75 

Fluid Cap 

250375 

+ 


14356 

2.1 522 877 2.8 681 1075 3.15 795 1174 3.85 953 1358 5.6 1158 1839 

2.45 522 962 3.15 681 1174 3.5 795 1273 4.2 953 1457 6.0 1158 1952 

2.8 522 1075 3.5 681 1273 3.85 795 1358 4.9 953 1641 6.3 1158 2037 

3.15 522 1174 3.85 681 1358 4.2 795 1457 5.25 953 1754 6.6 1158 2122 

– – – 4.2 681 1457 4.55 795 1556 5.6 953 1839 7.0 1158 2207 

– – – – – – 4.9 795 1641 6.0 953 1952 – – – 

2.45 

3.5 

3.85 

4.9 

6.3 

.20 

.35 

.50 

.70 

1.0 

21.6 

22.9 

24.1 

24.1 

25.4 

36.8 

42 

44.5 

46 

48 

52 

55 

58 

61 

66 

5.8 

6.7 

7.0 

7.6 

8.9 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F47


1/2J Series 



360° Circular Spray 


Set-up 

No. 

SU380C 


Set-up 


Fluid and 



Fluid Cap 

251376 

+ 


469-6-130- 

160HC 


Press. 




0.7 1.4 2.1 2.8 4.2 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 


Press. 

l/h 


l/min 

1.0 213 345 1.7 394 453 2.5 439 634 3.35 462 787 5.0 484 1138 

1.1 145 418 1.8 324 526 2.65 372 702 3.5 416 843 5.2 439 1197 

1.25 97.6 575 1.95 275 574 2.8 322 750 3.65 372 891 5.3 409 1254 

1.4 59 538 2.1 207 642 2.95 277 818 3.8 325 956 5.5 366 1310 

– – – 2.25 159 702 3.1 272 874 3.9 282 1019 5.6 325 1367 

– – – 2.4 116 758 3.2 188 931 4.05 250 1084 5.8 297 1429 

– – – 2.5 93 829 3.35 145 990 4.2 209 1135 5.9 257 1486 

– – – 2.65 27 900 3.5 114 1050 4.35 168 1189 6.0 232 1551 

– – – – – – – – – 4.5 141 1259 6.3 182 1670 

– – – – – – – – – 4.6 77 1296 – – – 


Odor control at a compost facility using air atomizing nozzles. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F48


External Mix, 1/2J Series 


C 

B 

A 


Fluid cap 

Round spray siphon air caps 

produce a round spray pattern. 

Round spray 

pattern 

D 

9" 

(23 cm) 

18" (46 cm) 

27" (69 cm) 

1705 

retainer ring 

1705 retainer ring and 8491 gasket must be ordered separately from the spray set-up, 

but are included in the standard nozzle assembly. Please contact your sales engineer. 

Refer to page F3 for Siphon/Gravity-Fed Liquid Spray Set-ups diagram. 

8491 

gasket 


Round Spray Siphon Set-ups 



Set-up 

No. 

SU70 


Set-up 


Fluid and 



Fluid Cap 

250375 

+ 


437 


Press. 




Capacity 

l/min 





45 30 15 10 20 30 60 

.70 360 – – – 40 – – – 

1.5 570 – – – 97 64 – – 

2.0 660 – – – 117 90 – – 

3.0 870 – 260 225 150 123 90 – 

3.5 990 300 265 235 163 133 104 – 

4.0 1100 305 270 240 170 143 115 – 

5.0 1300 315 280 250 183 157 129 53 

5.6 1450 320 290 255 188 164 136 62 


1.5 

2.0 

3.0 

3.5 

4.0 

5.0 

5.6 



A 

(cm) 

8 

8 

8 

8 

8 

8 

8 

B 

(cm) 

15 

15 

15 

15 

15 

15 

15 

C 

(cm) 

22 

22 

22 

22 

22 

22 

22 

D 

(m) 

6.1 

6.7 

7.3 

7.9 

8.8 

9.8 

10.7 



Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F49


1J Series 


1J 

1JN 

1J Series air atomizing 


1 2 3 

4 



3. Fluid cap 


Plug CP1706 

Shut-off 


1J 

1JN 


1" NPT or BSPT (F) 

1" NPT or BSPT (F) 

with shut-off needle 

• Range in capacity from 24 to 1740 gph (91 to 6586 l/h). 

• Available with a shut-off needle. 

• 1J features liquid and air feeds at opposite ends of the body and 

are provided with a removable plug so other needle assemblies 

may be added in the future. 

• 1JN features a manual shut-off needle that enables the flow of 

liquid to be stopped. 


See Also 

http:// 


Materials 





Ordering Info 



– Strainers 

Nozzle Bodies 

Material 

Material 


Nozzle Type 

Nickel-plated Brass (none) l l 

303 Stainless Steel SS l l 




J 

JN 

SSBR l l 



Nozzle Body* 



1 JN – SS + SU159 – SS 

l l l l l 

Inlet 


Nozzle 

Body 

Assembly 

Type 

Material 



Set-up 

No. 

Material 







performance data charts) and material code: 1109-6-224-70-SS. 

To order spray nozzle without set-up, use inlet connection, 

nozzle body and material code: 1JN-SS. 



SU159 – 

l 


Set-up 

No. 

SS 

l 

Material 




number and material 

code: SU159-SS. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F50


1J Series 


Wide angle round, round, 

and flat spray air caps 

produce hollow cone, wide 

angle round spray, round 



• For wide angle round, round and flat sprays, dimensions “A”, “B” and “C” are the pattern widths 

at distances from the nozzle. 





C 

B 

A 


Fluid cap 


D 

12" 

(30 cm) 

30" (76 cm) 

48" (122 cm) 

5713 retainer ring must be ordered separately from the spray set-up, but is included in 





Wide Angle Round 


Set-up 

No. 

SU159 


Set-up 


Fluid and 



Fluid Cap 

4371000 

+ 


1109-6-224- 

70° 


Pattern 

Wide 

Angle 

Round 


l/min 

Press. 


Liquid Capacity (liters per minute)* and Air Capacity (liters per minute)* 


0.7 1.5 2 3 4 


l/min 


l/min 

Press. 


l/min 


l/min 

Press. 


l/min 


l/min 

Press. 


l/min 


l/min 

Press. 


l/min 

.85 12.1 1220 1.8 16.3 1840 2.2 19.5 2050 3.1 30 2360 4.2 33 3110 

1.0 9.1 1440 2.0 13.2 2110 2.4 16.1 2350 3.2 26 2650 4.4 30 3410 

1.1 6.4 1730 2.1 10.7 2420 2.5 13.3 2650 3.4 23 2940 4.5 26 3720 

– – – 2.2 8.5 2720 2.7 11.2 2940 3.5 19.7 3240 4.6 24 4040 

– – – 2.4 6.8 3030 2.8 9.2 3230 3.7 17.0 3530 4.8 21 4330 

– – – – – – 3.0 7.6 3510 3.8 14.7 3820 4.9 18.9 4670 

– – – – – – – – – 3.9 12.7 4120 5.1 17.0 5010 

– – – – – – – – – 4.1 11.0 4420 5.2 15.2 5380 

– – – – – – – – – 4.2 9.5 4810 5.3 13.7 5750 


1.0 

1.8 

2.2 

2.2 

3.0 

3.5 

4.2 

4.2 

5.1 

Liquid* 

.70 

1.5 

1.5 

2.0 

2.0 

3.0 

3.0 

4.0 

4.0 


Dimensions 

A 

(cm) 

48 

53 

43 

56 

48 

51 

43 

55 

48 

B 

(cm) 

94 

102 

84 

107 

93 

112 

102 

119 

104 

C 

(cm) 

140 

150 

119 

147 

137 

157 

137 

170 

142 

D 

(m) 

4.3 

5.4 

7.6 

7.0 

10.0 

11.3 

14.0 

12.8 

15.5 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F51


1J Series 



Round and Flat Spray 


Set-up 

No. 

SU152 

SU172 

SU155 


Set-up 


Fluid and 



Fluid Cap 

4371000 

+ 


11091547 

Fluid Cap 

6251000 

+ 


11251625 

Fluid Cap 

4371000 

+ 


11093187 


Pattern 

Round 

Round 

Flat 


l/min 

Press. 




0.7 1.5 2 3 4 


l/min 


l/min 

Press. 


l/min 


l/min 

Press. 


l/min 


l/min 

Press. 


l/min 


l/min 

Press. 


l/min 

.85 12.1 1220 1.8 16.3 1840 2.2 19.5 2050 3.1 30 2360 4.2 33 3110 

1.0 9.1 1440 2.0 13.2 2110 2.4 16.1 2350 3.2 26 2650 4.4 30 3410 

1.1 6.4 1730 2.1 10.7 2420 2.5 13.3 2650 3.4 23 2940 4.5 26 3720 

– – – 2.2 8.5 2720 2.7 11.2 2940 3.5 19.7 3240 4.6 24 4040 

– – – 2.4 6.8 3030 2.8 9.2 3230 3.7 17.0 3530 4.8 21 4330 

– – – – – – 3.0 7.9 3510 3.8 14.7 3820 4.9 18.9 4670 

– – – – – – – – – 3.9 12.7 4120 5.1 17.0 5010 

– – – – – – – – – 4.1 11.0 4420 5.2 15.2 5380 

– – – – – – – – – 4.2 9.5 4810 5.3 13.7 5750 

.85 22 1370 1.7 37 1780 2.0 48 1560 3.1 54 2270 4.1 65 2360 

1.0 16.7 2320 1.8 32 2290 2.1 42 1950 3.2 49 2630 4.2 61 2660 

1.1 13.1 3620 2.0 28 3000 2.2 37 2400 3.4 46 3030 4.6 52 3480 

1.3 10.4 5300 2.1 25 3840 2.4 34 2920 3.5 42 3510 4.9 46 4520 

– – – 2.2 22 4930 2.5 30 3430 3.7 39 3990 – – – 

– – – – – – – – – 3.8 37 4590 – – – 

.85 12.1 1220 1.8 16.3 1840 2.2 19.5 2050 3.1 30 2360 4.2 33 3110 

1.0 9.1 1440 2.0 13.2 2110 2.4 16.1 2350 3.2 26 2650 4.4 30 3410 

1.1 6.4 1730 2.1 10.7 2420 2.5 13.3 2650 3.4 23 2940 4.5 26 3720 

– – – 2.2 8.5 2720 2.7 11.2 2940 3.5 19.7 3240 4.6 24 4040 

– – – 2.4 6.8 3030 2.8 9.2 3230 3.7 17.0 3530 4.8 21 4330 

– – – – – – 3.0 7.6 3510 3.8 14.7 3820 4.9 18.9 4670 

– – – – – – – – – 3.9 12.7 4120 5.1 17.0 5010 

– – – – – – – – – 4.1 11.0 4420 5.2 15.2 5380 

– – – – – – – – – 4.2 9.5 4810 5.3 13.7 5750 


1.0 

1.8 

2.2 

2.2 

3.0 

3.5 

4.2 

4.2 

5.1 

1.0 

1.7 

2.5 

3.2 

4.6 

1.0 

1.8 

2.2 

2.2 

3.0 

3.5 

4.2 

4.2 

5.1 

.70 

1.5 

1.5 

2.0 

2.0 

3.0 

3.0 

4.0 

4.0 

.70 

1.5 

2.0 

3.0 

4.0 

.70 

1.5 

1.5 

2.0 

2.0 

3.0 

3.0 

4.0 

4.0 


Dimensions 

A 

(cm) 

10.2 

10.2 

10.2 

10.2 

10.2 

10.2 

10.2 

12.7 

12.7 

15 

15 

15 

15 

15 

74 

81 

58 

94 

81 

94 

74 

124 

96 

B 

(cm) 

20 

20 

23 

23 

23 

23 

25 

23 

23 

28 

28 

25 

25 

28 

152 

163 

127 

185 

167 

183 

150 

223 

203 

C 

(cm) 

30 

33 

33 

33 

33 

36 

38 

33 

35 

33 

36 

36 

36 

38 

213 

234 

178 

246 

228 

264 

224 

320 

284 

D 

(m) 

9.1 

11.0 

12.5 

11.9 

14.0 

16.5 

19.2 

17.9 

21.3 

7.6 

9.1 

10.7 

12.8 

15.2 

6.4 

7.0 

7.9 

7.3 

8.5 

9.1 

10.0 

9.4 

10.3 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F52

Pressure Spray and Siphon/Gravity-Fed 

Spray Set-ups, External Mix, 1J Series 


Flat spray and round 

spray air caps produce a 

flat spray pattern and the 

siphon air caps produce a 

round spray pattern. 


• For flat spray, dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle. 

– The total distance of spray projection from the nozzle to the maximum dispersal point is 


– When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. 

– The liquid and compressed air or gas are mixed externally to produce a completely atomized spray. 

• For round spray, dimensions “A”, “B” and “C” are the pattern widths at distances from the nozzle. 

– The total distance of spray projection from the nozzle to the maximum dispersal point is 


– When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid siphon or 

a gravity-feed. 

– Designed to draw liquid through the feed line into the air flow where it is atomized. 

C 

B 

A 


Fluid cap 


D 

Flat spray 

pattern 

12" 

(30 cm) 

30" (76 cm) 

48" (122 cm) 


12415 retainer ring must be ordered separately from the spray set-up, but is included 

in the standard nozzle assembly. Please contact your sales engineer. 





Set-up 

No. 

SUE175B 


Set-up 


Fluid and 



Fluid Cap 

625780 

+ 


12116 


Pattern 

Flat 


l/min 

Press. 




0.2 0.3 0.5 0.7 1 


l/min 


l/min 

Press. 

Siphon Set-ups Round Spray 


Set-up 

No. 

SU170 


Set-up 


Fluid and 



Fluid Cap 

6251000 

+ 


1125 


l/min 


l/min 

Press. 


l/min 


l/min 

Press. 


l/min 


l/min 

Press. 


l/min 

1.4 49 2460 1.8 59 2860 2.1 76 3260 2.8 90 3960 3.5 107 4700 

1.8 49 2860 2.1 59 3260 2.8 76 3960 3.5 90 4700 4.2 107 5410 

2.1 49 3260 2.8 59 3960 3.5 76 4700 4.2 90 5410 4.9 107 6120 

2.8 49 3960 3.5 59 4700 4.2 76 5410 4.9 90 6120 5.6 107 6850 

3.5 49 4700 4.2 59 5410 4.9 76 6120 5.6 90 6850 6.3 107 7590 

4.2 49 5410 4.8 59 6120 5.6 76 6850 6.3 90 7590 – – – 


Press. 




Capacity 

l/min 

Refer to page F3 for Siphon/Gravity-Fed Liquid Set-ups. 



(liters per minute)* 



45 30 15 10 20 30 60 

1.4 2971 – – 12.9 7.2 – – – 

1.75 3396 19.7 17.0 13.6 8.3 – – – 

2.1 3821 20.1 17.4 14.4 9.1 5.3 – – 

2.8 4670 20.4 17.8 14.8 9.8 6.8 4.2 – 

4.2 6368 20.8 18.5 15.9 11.0 8.3 5.7 1.5 

5.6 8066 21.2 18.9 16.6 11.4 8.7 6.1 1.9 

7.0 9764 21.6 19.3 17.0 11.7 9.1 6.4 2.3 


Dimensions 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F53 


2.1 

2.8 

3.5 

4.2 

4.9 


2.1 

2.8 

4.2 

5.6 

7.0 

Liquid* 

.20 

.30 

.50 

.70 

1.0 

A 

(cm) 

51 

56 

58 

56 

56 

B 

(cm) 

91 

94 

99 

97 

99 

C 

(cm) 

119 

122 

130 

124 

127 



A 

(cm) 

13 

13 

13 

13 

13 

B 

(cm) 

26 

26 

26 

26 

26 

C 

(cm) 

38 

38 

38 

38 

38 

D 

(m) 

7.6 

8.5 

9.1 

9.8 

10.7 

D 

(m) 

8.8 

10.5 

13.4 

16.5 

19.5

Fogger Spray Nozzles, 



23412 


threaded type 

QJ25655 

Split-eyelet type to clamp on 

1/2", 3/4", 1" pipe size 


• 23412 produces high quality, cost-efficient dry fog. 

– Drops average fifteen microns in size and less. 

– Drop size is adjustable to meet specific industrial needs by 

changing the ratio of compressed air to water. 

– Maintenance time is reduced because the built-in check 

valve, spray tip, and internal strainer are quickly serviced 

without tools. 

– Can use PVC pipe and low-pressure air tubing. 

– Tip has a relatively large clog-reducing orifice. 

• QJ25655 provides fast installation of the nozzle onto the liquid 

supply pipe – no additional pipe fittings are required. 

– Pipe cutting, threading and brazing are eliminated. 

– Features a chemical-resistant, tight-fitting Buna-N seal to 

ensure leak-free performance. 

Ordering Info 

Specifications 

Complete Nozzle 

Assembly 

23412 – 1/4 – 20 

l l l 

Nozzle 

Body 

Inlet 


Fluid 

Orifice 

Dia. 


Assembly 

QJ25655 – 3/4 – 20 

l l l 

Nozzle 

Body 

Pipe 

Size 

Fluid 

Orifice 

Dia. 

BSPT connections require the addition of a “B” prior to the nozzle body 

inlet connection. 

Nozzle 

Inlet 

(in.) 

AirJet 

Fogger 

Type 

1/4 23412 

To Clamp On 

Pipe 

Size 

(in.) 

1/2 


Fogger 

Type 

Fluid 

Orifice 

No. 

Orifice 

Dia. 

Nom. 

(mm) 

16 .41 

20 .51 

26 .66 

Fluid 

Orifice 

No. 

Orifice 

Dia. 

Nom. 

(mm) 

16 .41 

3/4 QJ25655 

20 .51 

1 26 .66 

Humidification to reduce static charge in paint manufacturing plants. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F54




23412, QJ25655 

Water 

Pressure 

1.5† 

2 

3 

3.5 

4 

5 

5.5 

6 

7 

Fluid Orifice No. 16 (0.41 mm Dia.) 

Air Pressure* 


0.7 1.5 2 3 3.5 4 5 5.5 

4.5 4.2 – – – – – – 

42 71 – – – – – – 

6.4 6.1 4.5 – – – – – 

40 68 96 – – – – – 

7.6 6.1 5.7 5.3 – – – – 

40 68 93 119 – – – – 

7.9 7.2 6.4 5.7 4.9 – – – 

40 65 91 119 142 – – – 

8.7 7.9 7.2 6.4 5.3 4.9 3.0 – 

37 65 91 116 142 164 193 – 

9.8 9.1 8.3 7.2 6.4 6.4 5.7 3.8 

37 65 88 113 139 161 190 215 

10.2 9.8 9.1 8.3 7.6 7.2 6.4 6.1 

37 62 88 113 139 161 187 212 

11.0 10.6 9.8 9.1 8.3 7.6 7.2 7.2 

34 59 88 110 133 161 184 212 

11.7 11.4 10.6 9.8 9.1 8.7 8.3 8.3 

34 59 85 110 133 159 184 212 

23412, QJ25655 

Water 

Pressure 

1.5† 

2 

3 

3.5 

4 

5 

5.5 

6 

7 




0.7 1.5 2 3 3.5 4 5 5.5 

11.7 6.4 – – – – – – 

40 79 – – – – – – 

13.6 7.9 6.4 – – – – – 

37 71 102 – – – – – 

16.3 11.7 8.3 – – – – – 

34 65 96 – – – – – 

18.5 14.0 11.7 8.7 – – – – 

34 62 91 119 – – – – 

– 16.3 14.0 11.7 8.3 – – – 

– 59 85 110 142 – – – 

– 18.2 16.3 13.6 11.7 7.9 – – 

– 57 82 108 136 167 – – 

– 20 18.5 15.9 14.0 11.7 8.3 – 

– 54 76 102 130 159 190 – 

– – 20 18.5 16.3 13.6 11.7 – 

– – 74 99 125 153 205 – 

– – 22 20 18.2 16.3 14.0 11.7 

– – 71 93 122 150 167 205 



23412, QJ25655 

Water 

Pressure 

1.5† 

2 

3 

3.5 

4 

5 

5.5 

6 

7 




0.7 1.5 2 3 3.5 4 5 5.5 

12.5 6.8 – – – – – – 

37 68 – – – – – – 

16.3 12.9 7.9 – – – – – 

31 59 91 – – – – – 

– 17.0 13.6 9.1 – – – – 

– 54 79 110 – – – – 

– 20 17.4 14.0 9.5 3.4 – – 

– 51 76 102 133 167 – – 

– 23 20 17.8 14.4 10.6 4.9 – 

– 48 71 96 125 153 190 – 

– – 23 21 18.2 15.1 11.4 6.4 

– – 68 93 119 144 175 210 

– – 26 23 21 18.2 15.5 11.7 

– – 65 91 116 142 167 198 

– – 28 26 24 21 18.9 16.3 

– – 62 85 110 136 159 187 

– – 30 28 26 24 22 18.9 

– – 59 82 108 130 156 181 

†For applications with liquid pressures below 30 psi (2 bar), request 

end cap sub-assembly 21950-20-NYB. 

In each line, figures in plain face indicate water atomized in gph (l/h) at 

psi (bar) water pressure. 

Figures in boldface indicate atomizing air in scfm (Nl/min) at psi (bar) 

air pressure. 

AirJet Fogger has a horizontal throwing distance of 15' (4.5 m) and will 

expand to approximately 8' (2.4 m) wide/3' (.9 m) thick. 

1. Values in blue area show optimum evaporation under normal room 

conditions, when center line of spray is 5' (1.5 m) from the lower 

surface. 

2. Values in red area can require up to 10' (3 m) for evaporation. Other 

values may be used where extended heat, higher air velocity exist or 

where slight surface wetting is permitted. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F55

DripSafe 





• High-volume/high-efficiency air atomization. 

• Produces an adjustable, high-quality dry fog without wetting with 

pressure-fed liquid. 

• Ideal for large/open structures and areas with high air exchange rates. 

• Operation is through a drip safe air-actuated liquid shut-off valve. 

• Automatically prevents liquid from spraying until air pressure at the 

nozzle is sufficient for fine atomization. 

• Drip safe valve simplifies system construction and control while 

improving performance. 

• Operates using normal water pressures found in municipal water 

systems, eliminating the need for expensive, high-pressure hydraulic 

pumps. 

• Air requirements are met using an air compressor with a 

capacity range that is suitable for the application. 

• Requires minimal maintenance. 

• The flat spray tip has a large orifice that reduces clogging. 

• Spray set-up and built-in strainer are quickly removed by 

hand if cleaning is required. 

• Spray tip is brass; valve and body polymer. 

• Operates at pressures up to 100 psi (7 bar) with a minimum 

air pressure range of 25 to 35 psi (1.7 to 2.5 bar). 

• A split-eyelet or saddle clamp version of the AirJet 

Fogger (45269 Series) is also available for quick and easy 

mounting to the liquid supply pipe. 

45265 

45269 



Applications 

1/4" NPT or BSPT (F) Split-eyelet type to clamp on 

pipe 1/2" to 1" 

• Evaporative cooling 

• Fogging 

• Humidification 

• Insecticide spraying 

• Plant propagation 

Specifications 

Nozzle 

Inlet 


(in.) 


Fogger 

Type 

1/4 45265 

Fluid 

Orifice 

No. 

Orifice 

Dia. 

Nom. 

(mm) 

16.0 .41 

20 .51 

26 .66 

See Also 







– Strainers 

• For 23412 and QJ25655, request Data Sheets 23412 

and 25635 

• For 45265 and 45269, request Data Sheets 45265-1-2 

and 45269-1-2 

http:// 

To Clamp On 

Pipe 

Size 

(in.) 

1/2 


Fogger 

Type 

Fluid 

Orifice 

No. 

Orifice 

Dia. 

Nom. 

(mm) 

16.0 .41 

3/4 45269 

20 .51 

1 26 .66 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F56

DripSafe 




45265, 45269 

Water 

Pressure 

1.5 

2 

2.8 




0.7 1.5 2 3 3.5 4 5 5.5 

4.5 4.2 – – – – – – 

42 71 – – – – – – 

6.4 5.7 4.5 – – – – – 

40 68 96 – – – – – 

7.6 6.4 5.7 5.3 – – – – 

40 68 93 119 – – – – 

45265, 45269 

Water 

Pressure 

1.5 

2 

2.8 




0.7 1.5 2 3 3.5 4 5 5.5 

11.7 6.4 – – – – – – 

40 79 – – – – – – 

13.6 7.9 6.4 – – – – – 

37 71 102 – – – – – 

16.3 11.7 8.3 – – – – – 

34 65 96 – – – – – 

45265, 45269 

Water 

Pressure 

1.5 

2 

2.8 




0.7 1.5 2 3 3.5 4 5 5.5 

12.5 6.8 – – – – – – 

37 68 – – – – – – 

16.3 12.9 7.9 – – – – – 

31 59 91 – – – – – 

– 17.0 13.6 9.1 – – – – 

– 54 79 110 – – – – 

In each line, figures in plain face indicate water atomized in gph (l/h) 

at psi (bar) water pressure. 

Figures in boldface indicate atomizing air in scfm (Nl/min) at psi (bar) 

air pressure. 

1. Values in blue area show optimum evaporation under normal 

room conditions, when center line of spray is 5' (1.5 m) from the 

lower surface. 

2. Values in red area can require up to 10' (3 m) for evaporation. 

Other values may be used where extended heat, higher air 

velocity exist or where slight surface wetting is permitted. 

3. AirJet Fogger has a horizontal throwing distance of 15' (4.5 m) 

and will expand to approximately 8' (2.4 m) wide/3' (.9 m) thick. 



Ordering Info 


Assembly 

45265 – 1/4 – 16 

l l l 

Nozzle 

Body 

Inlet 


Fluid 

Orifice 

Dia. 


Assembly 

45269 – 1/2 – 16 

l l l 

Nozzle 

Body 

Pipe 

Size 

Fluid 

Orifice 

Dia. 

BSPT connections require the addition of a “B” prior to the nozzle body 

inlet connection. 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F57

Humidification Spray Nozzles and Units 



• All equipment supplied for humidification systems except piping 

and wiring. 

• 1/4JH siphon air atomizing nozzles provide automatic, efficient 

humidity control with low installation and operating costs. 

– Nozzles operate either with compressed air drawing water 

from the float box by siphon action, or with water being 

delivered to the nozzle under pressure. 

– Produces a fine atomized spray for rapid evaporation and 

efficient humidification. 

– For information on siphon set-ups, see pages F23 to F53. 

• 1/4JT pressure-fed air atomizing nozzles provide automatic, 

efficient humidity control with low installation and operating 

costs. 

– Suitable for use in systems where water is under pressure. 

– Have built-in strainers for air and water plus a ball check valve 

in the water line. 

– Produces a fine atomized spray for rapid evaporation and 

efficient humidification. 

– For information on pressure set-ups, see pages F5 to F48. 

• 45400 humidification unit is a self-contained humidifier suitable 

for use with deionized water (DI). 

– Easy to install on a wall or for use in non-ducted applications. 

– Air regulator and gauge, 24VDC air control solenoid and air line 

filter are included within the Humidification Unit. 

– Wall-mounting bracket is also provided. 

– 9.7 lbs. (4.4 kg). 

– For each spray set-up, water capacity ranges from 2.7 lbs./hr 

at 10 psi (0.7 bar) air to 6.5 lbs./hr at 60 psi (4 bar) air. 

• YMF MiniFogger ® III is ideal for humidification applications with 

limited space due to its compact design. 

– Available with a choice of one to four stainless steel spray 

nozzle set-ups with a wide variety of flow-rate sizes/droplet 

sizes and types. 

– For each spray set-up, water capacity is 0.26 to 1.19 gph 

(1.0 to 4.5 l/h), and air capacity is 30 to 35 nl/min at 43.5 psi 

(3.0 bar). 

– Can be placed in hard-to-reach spaces and can be easily 

installed on a header, on a wall or on a ceiling. 

– 0.46 lbs. (210 g) for single spray set-up type; 0.55 lbs. (250 g) 

for multiple four set-up types. 

– Height is 4.53" (115 mm). 

– The body, retainer cap, and tank are made of corrosionresistant 

polypropylene with stainless steel air and water 

connections. 

– Materials are also compatible with deionized water. 

• 46215-008 provides a finely atomized spray without the use of 

compressed air. 

– Produces a hollow cone spray pattern. 

– Requires a minimum liquid pressure of 450 psi (31 bar) 

to the nozzle. 

– Maximum operating pressure of 1000 psi (69 bar). 

1/4JH 

45400 

YMF 

46215-008 

Siphon inlet connection 

1/4" NPT and BSPT inlets 

1/4JT 


MiniFogger III 


air and liquid inlet connection 


misting nozzle 

Pressure-fed inlet connection 

1/4" NPT and BSPT inlets 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F58

Humidification Spray Nozzles and Units 


Materials 


See Also 





YMF MiniFogger III 

Set-up 

No. 

45400 


Press. 

bar 

Orifice 

Diameter 

(mm) 




Capacity 

l/min 

Water 

Capacity 

l/h 

.7 10.7 1.2 

1.4 16.1 1.6 

2 20.9 2.0 

2.8 25.9 2.3 

3.5 31.0 2.7 

4 36.7 3.0 

Data per Nozzle (Air Pressure 0.3 MPa) 

Liquid 

Capacity 

l/h 


Capacity 

l/min 

Mean 

Droplet Size 

(micron)* 

Pressure 

bar 


Distance 

(m) 

SU2.5N 0.54 2.5 35 8.5 2.7 

*Sauter Mean Diameter 

0.1 MPa = 1 bar 




• For 1/4JH siphon air atomizing nozzles, request 


• For 1/4JT pressure-fed air atomizing nozzles, request 


• For 45400 humidification unit, request Data Sheet 45400 

• For YMF MiniFogger ® III, request Data Sheet YMF 

46215-008 

Liquid 

Capacity 

l/h 

35 3.6 

41 3.8 

48 4.2 

55 4.5 

62 4.7 

69 4.9 

A – Float box with float valve 

B – TW liquid strainer 

C – Air atomizing nozzle 

D – Spray pipe assembly 

E – Pipe hanger 

F – Air filter 

G – Pressure regulator with gauge 

H – Solenoid valve 

I – Switching relay 

J – Humidistat 

http:// 

Nozzle Bodies 

Material 

Material 


Nozzle Type 

JH JT 45400 YMF 46215 

Brass (none) l 

Nickel-plated Brass (none) l l 

Kynar ® KY l 


Air/Fluid Caps 

Nickel-plated Brass SSBR l l 



SSBR l l 

Kynar KY l 


PTFE TEF l 

Ordering Info 


Nozzle Body* 


1/4 JH – SS + SU1A – SS 

l l l l l 

Inlet 


Nozzle 

Body 

Material 




Set-up 

No. 

Material 




To order spray set-up only, use spray set-up number 

and material code: SU1A-SS. 






connection, nozzle body and material code: 1/4JH-SS. 

A 

Humidification 

Unit 

YMF-3 – 4 

l l 


Unit 

Type 

No. 

of 

Set-ups 


Unit 

45400 – 1 

l l 


Unit 

Type 

Typical humidifying set-ups for siphon nozzles 

G 

B 

F 

I 

H 

C 

D 

E 

J 

No. 

of 

Set-ups 



Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F59

Humidification System Components 



• 2335-SE pipe assembly consists of straight and formed tubing 

with fittings, globe valve and split-eyelet connectors. 

– Not assembled. 

• 11438-85 humidistat will respond to humidity levels in the 

range of 20% to 95% RH. 

– Maximum operating temperature 125°F (52°C). 24V DC; 110V. 

Overall height 6" (15 cm). 

• 11438-95 switching relay has built-in transformer that supplies 

low-voltage current for humidistat circuit. 

– 2-wire 24V control, 115V AC. Maximum temperature 115°F 

(46°C). 

• 55089 electric humidistat quick relative humidity LCD readouts 

from 1% to 99% with repeatability of ±5%. 

– Operating temperature range 32°F to 160°F (0°C to 71°C). 

– 24V (DC or AC). 

• 45604 float valve used in 45600 float box to shut off inlet flow 

at a preset water level. 

– Made of ABS plastic, 304 Stainless Steel, polypropylene 

with fiber washers and a brass nut. 



• 55400 valve package is easy to install and use – simply connect 

to existing air and fluid lines. 

– The NEMA type 4 panel is completely sealed to eliminate moisture 

damage to components. 

– Safety feature ensures there is no product damage due to 

unintentional water release. 

– Stainless steel components available for use with deionized water. 

– Separate atomizing and cylinder air lines with adjustable delay 

time assures liquid atomization. 

• 2202 pipe hanger for proper spacing between air and liquid lines. 

Sizes fit 1/2" piping. 

– Hanger is held by threaded rod and nuts (not included) for 

vertical adjustment. 

– Made of cast aluminum. 4" (10 cm) spacing. 

– Use with 2335-SE spray pipe assembly. 

See Also 





• Section L, Accessories 



– Strainers 

• For 2335-SE pipe assembly, request Data Sheet 2335-SE 

• For 55089 electrical humidistat, request Data Sheet 55089 

http:// 

2335-SE 

11438-85 11438-95 

55089 

Spray pipe assembly 

Humidistat 

Switching relay 

Electric humidistat 

45604 45600 

55400 

2202 

Float valve 

Float box 

Valve package 

Pipe hanger 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F60

Air Atomizing Accessories 


• 22140 pressure tank assembly meets ASME ® 

Boiler and Pressure 

Vessel Code requirements and OSHA safety regulations. 

– Constructed of 304 Stainless Steel. 

– Assembly includes a pressure regulator with gauge, ASME 

coded pressure relief valve, air bleed valve and plug valves 

for air inlet and liquid outlet. 

– Tanks are available in 1, 2, 5 and 10 gallon (3.8, 7.6, 18.9 and 

38 liter) capacities. 

– The air inlet and liquid outlet have 1/4" NPT (F) connections. 

– The maximum working pressure is 140 psi at 100°F (9.5 bar 

at 38°C). 

– The 22140 features brass fittings and an EPR lid seal. 

• 38180 split-eyelet swivel union simplifies installation and 

maintenance of air atomizing nozzles and spray guns. 

– Connector design reduces costs by eliminating cutting, 

threading, welding and brazing operations and adjustment 

of fittings, unions and nipples. 

– Recommended pressure is up to 250 psi (17 bar) for liquid 

and air lines. 

– Fits 1/2", 3/4" or 1" pipe or similar O.D. tube. 1/4" NPT or 

BSPT (M) outlet pipe connections. 

– Nickel-plated brass with zinc-plated pipe clamps or all 

stainless steel construction. 

• 39273, 39275 level switch kit indicates a low liquid level condition 

inside the pressure tank. 

– Use standard 39273 level switch with 5 and 10 gallon (18 and 

38 liter) pressure tank assemblies with external 1/4" NPT (F) 

threads. 

– Use 39275 level switch with 1 and 2 gallon (4 and 8 liter) 

pressure tank assemblies with external 1/4" NPT (F) threads. 

– Features a U.L. listed float switch, quick disconnect and 12' 

(3 m) PVC jacketed cable. 

– Available in brass with Buna-N float or all stainless steel. 

• 39272 tank heater bands provide anywhere from 6°F to 60°F (3°C 

to 33°C) heat gain depending upon the tank size and number of 

bands used. 

– Silicone rubber construction with fiberglass mesh 

reinforcement for added strength, flexibility, and corrosion 

resistance. 

– Features quick-release band clasp and built-in thermostat for 

temperature control. 

– Two sizes fit 9" and 12" (288.6 and 304.8 mm) diameter tanks. 

• 38673 push-in tube fittings provide fast and easy hook-up of 

air atomizing nozzles. 

– Durable nickel-plated brass construction includes Buna-N 

O-ring. 

– Select from six configurations with 1/8", 1/4" or 3/8" NPT (M) 

connections for 1/4", 3/8" and 1/2" O.D. tubing. 

• 45592 ferrule-type tube fittings are intended for use when 

operating at higher pressures. 

– The 316 Stainless Steel is of durable construction and can be 

easily taken apart for cleaning. 

– Six configurations available with 1/8", 1/4" or 3/8" NPT 

connections for 1/4", 3/8" and 1/2" O.D. tubing. 

• 38691 and 38692 strong, semi-rigid nylon tubes designed for use 

with 38673 fittings. 

– Abrasion resistant and dimensionally stable tubing available in 

12', 25' and 50' (3.6 m, 7.5 m and 15 m) lengths. 

– Maximum working pressure is 250 psi (17 bar) at –40°F to +70°F 

(–40°C to +20°C). 

– 38691 has 1/4" O.D. 

– 38692 has 3/8" O.D. 



Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F61

Air Atomizing Accessories 


22140 

38180 

Pressure tank assembly Split-eyelet swivel union 


39273 and 

39275 

38673 and 

45592 

39272 

Level switch kit Tube fittings Tank heater bands 

See Also 

http:// 


• For 22140 pressure tank assembly, request Data Sheet 22140 

• For 38180 split-eyelet swivel union, request Data Sheet 38180 

• For 39273, 39275 level switch kit, request Data Sheet 39275 and 39273 

• For 39272 tank heater bands, request Data Sheet 39272 

• For 38673, request Data Sheet 38673 

• For 45592 ferrule-type tube fittings, request Data Sheet 45592 

• For 38691 and 38692, request Data Sheets 38691 and 38692 

Phone 1(630) 665-5000, FAX 1(630) 260-0842 


F62

Section F â Air Atomizing Spray Nozzles - Spraying Systems Co.

Create successful ePaper yourself

Delete template?

Save as template?

Section F â Air Atomizing Spray Nozzles - Spraying Systems Co.