Model 22 Series II - Cybarcode, Inc.

More documents

Recommendations

Info

3-16 MODEL 22 SERIES II OPERATIONS AND MAINTENANCE MANUAL Accu-Sort Systems Interface Box End of Cable (15 pin "D" male) Note: Connectors are shown from the soldering side The shield is electrically connected to both cable shells. Pin Connections for Connections Between The Interface Box and the Model 22 Series II Model 22 End of Cable J1 or J3 (15 pin female "D")
MAKING CONNECTIONS TO YOUR MODEL 22 SERIES II 3-17 USING MODEL 22 SERIES II PARALLEL OUTPUTS The Model 22 Series II has two parallel outputs; NVC/NO MATCH and GO/MATCH. These outputs are activated or deactivated from pin 4 and pin 5 respectively on the Model 22 Series II 15-pin connector. Both of these are controlled by software. (Refer to your Accu-Setup Small Scanner Module Programming Manual.) You can use these outputs to have a beeper sound when you receive a no read or no match (when used as a verifier), or you could have a light turn on every time there is a go (good read) or match (when used as a verifier). There are many other uses for these outputs. When you connect these pins to the small scanner interface box, they control the relays in the box. HOW THE OUTPUTS WORK The names of the two outputs directly reflect their purpose. The NVC/NO MATCH output changes its electrical state dependent on receiving a no read or a no match (while in verifier mode). The GO/MATCH output changes its electrical state dependent on receiving a good bar code or a match (while in verifier mode). For example, if you set the NVC/NO MATCH timer for 150 milliseconds, every time the scanner sees a non-valid bar code the NVC/NO MATCH timer signals until that 150-millisecond time period is complete. Solutions with Vision
Page 1: Model 22 Series II Bar Code Scanner
Page 5 and 6: INTRODUCTION This is the Operations
Page 7 and 8: CUSTOMER SERVICE If you have any pr
Page 9 and 10: GENERAL PRECAUTIONS Please follow t
Page 11 and 12: LABEL LOCATIONS The following label
Page 13 and 14: Table of Contents Chapter One Intro
Page 15 and 16: Table of Figures PARTS TABLE.......
Page 17 and 18: Chapter One Introduction 1Heading 2
Page 19 and 20: INTRODUCTION 1-3 Supply Voltage Cab
Page 21 and 22: INTRODUCTION 1-5 Other Accessories
Page 23 and 24: INTRODUCTION 1-7 Typical applicatio
Page 25 and 26: Chapter Two Start-Up and Operation
Page 27 and 28: START UP AND OPERATION 2-3 MOUNTING
Page 29 and 30: START UP AND OPERATION 2-5 USING MO
Page 31 and 32: START UP AND OPERATION 2-7 SETTING
Page 33 and 34: Chapter Three Making Connections to
Page 35 and 36: MAKING CONNECTIONS TO YOUR MODEL 22
Page 47: MAKING CONNECTIONS TO YOUR MODEL 22
Page 51 and 52: Chapter Four Maintenance And Troubl
Page 53 and 54: MAINTENANCE AND TROUBLESHOOTING 4-3
Page 55 and 56: Appendices AHeading 2 Appendix A Co
Page 57 and 58: A-3 The remainder of this section d
Page 59 and 60: SEQ (1 ASCII digit) = The sequence
Page 61 and 62: Both the master and the slave must
Page 63 and 64: Multidrop Protocol Examples Message
Page 65 and 66: MESSAGE FORMAT The transmission of
Page 67 and 68: APPENDIX B: ASCII CHART HEXADECIMAL
Page 69 and 70: MODEL 22 SERIES II B - HIGH DENSITY
Page 71 and 72: MODEL 22 SERIES II D - LONG RANGE O
Page 73 and 74: Index A Accessories ...............
Page 75: Revision History Revision History D

Model 22 Series II - Cybarcode, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?