HM catalog Emission Control Technology 2015

Your partner for Laboratory & Environmental – 

Immission / Emissions sampling equipment dust gas sampling – 

Analysis - Occupational Safety - Laboratory Consumables - 

Special stainless steel for Medical Technology Laboratory Equipment - 

Special machines and plants

CONTENT 

content .............................................................................................................................................................................. 2 

We have everything for your emission sampling technique: .................................................................. 9 

Section Dust: .................................................................................................................................... 9 

Section Dioxins: ............................................................................................................................. 10 

Section PAH/PCB/Tar: .................................................................................................................... 10 

Section Gase: ................................................................................................................................. 11 

Section Acids: ................................................................................................................................. 12 

Suction Pyrometer ................................................................................................................................................... 12 

Gas Temperature Measurements with Suction Pyrometer according to IFRF (International Flame 

Research Foundation) and VDE: ............................................................................................ 12 

Gas Velocity - Flow .................................................................................................................................................. 13 

Gas Velocity - Flow EQUIPMENT FOR AIR AND GAS Speed Measurement with Pitot tubes 

....................................................................................................................................................... 13 

Probes / Nozzles for the Isokinetic Sampling .............................................................................................. 14 

Gooseneck-Curve with interchangeable nozzles ........................................................................... 14 

Nozzle for gooseneck bent ............................................................................................................ 14 

Gooseneck-Curve without nozzle .................................................................................................. 14 

Nozzles according to VDI 2066, page 2 and EN 13284-1 ............................................................... 14 

Bent for nozzles ............................................................................................................................. 14 

Goosenecknozzle acc. EN 13284-1 und ISO 9096:......................................................................... 14 

Nozzles according to VDI 2066, page 7 and EN 13284-1: .............................................................. 15 

Filter Device for Dust- and Aerosol Sampling (TSP) ................................................................................. 15 

Plane filter device for dust range up to 50 mg/m³ according to VDI 2066 and EN 13284 ............ 15 

Accessories for Plane filter ........................................................................................................ 15 

Plane filter device pecial for very low dust range (< 5mg/m³) Construction ................................ 16 

according to VDI 2066, page 7 page 8 and EN 13284 .................................................................... 16 

Accessories for Plane filter Entrance: Internal thread G ¾ conical. .................................. 16 

Simple tubular filter device ........................................................................................................... 16 

Accessories for Simple tubular filter device ............................................................................ 17 

High precision tubular filter device for dust range from 20 bis 2000 mg/m³, with back up plane filter (Ø 45 

mm). according to VDI 2066 and EN 13284 .................................................................................. 17 

Accessories for High precision tubular filter device for dust range from 20 bis 2000 mg/m³, 18 

High dust tubular filter device for dust range up to 100 g/m³ according to VDI 2066 and EN 13284. 19 

Accessories for High dust tubular filter device ....................................................................... 19 

Stainless Steel cyclone separator for dust range up to 500 g/m³ ................................................. 19 

HM Labortechnik e.K. - Oststrasse 54 - 41065 Mönchengladbach – GERMANY 

Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 

E-Mail: info@hm-labortechnik.com / Onlineshop. www.hm-labortechnik.eu 

2

Accessories for Cyclone Separator .......................................................................................... 19 

Plane filter device for plane filter Ø 110 mm for dust range up to 2000 mg/m³. ......................... 20 

Dust filter from Duran or Quartz Glass for special application ..................................................... 20 

Pre dust filter ................................................................................................................................. 20 

Small sampling equipment according to EN 13284-1 and ISO 9096 ............................................. 20 

Heater for Filter Device out of aluminum half-pipes. ................................................................................ 21 

The half-pipes are unfold and thus permit free acces to the filter device. Now the hot sections 

can be removed trouble-free by means of thin spanners. ...................................................................... 21 

Small heater ................................................................................................................................... 21 

Large heater ................................................................................................................................... 21 

Accessories for heater ............................................................................................................... 22 

Self-regulating small heater for filter devices ............................................................................... 22 

Accessories for Self-regulating small heater .......................................................................... 22 

Temperatur Controller for the Heater ........................................................................................... 23 

Accessories for Temperature controller .................................................................................. 23 

Glass- and Quartz Fibre Filter ............................................................................................................................. 24 

Plane filter from glass- and quartz fibre ........................................................................................ 24 

Plane filter holder .......................................................................................................................... 24 

Petri glasses for plane filter holder ............................................................................................... 24 

Transport suitcase for plane filter holder ...................................................................................... 24 

Filter thimbles for tubular filter device ......................................................................................... 24 

Quartz wool 500 g ......................................................................................................................... 24 

Filter husk for tubular filter device ................................................................................................ 25 

Cone ............................................................................................................................................... 25 

Transport glasses ........................................................................................................................... 25 

Suitcase for transport glasses ........................................................................................................ 25 

Suction tube / probe for isokinetic sampling ............................................................................................... 26 

Combination - probe: non heated, electrcal heated or water cooled Ø 60 mm ........................... 26 

Non heated probe Ø 25 mm .......................................................................................................... 26 

Electrical heated probe Ø 25 mm .................................................................................................. 27 

Heated Power-Plant-Probe with integrated heated filter in front of probe Ø 64 / 60 mm .......... 27 

Water cooled suction tube (Universal Probe) ............................................................................... 27 

GAS SAMPLE PROBES ..................................................................................................................... 27 

Accessories for Suction tube / probe for isokinetic sampling ....................................................... 28 

Pump, gas meter, flowmeter and isokinetic control unit ........................................................................ 29 

Flow measurement adapted from STRÖHLEIN ............................................................................. 29 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


3

Manual unit for volumetric determination ................................................................................... 29 

Compact and robust gas-sampler with CP-Modul for gas sampling up to 320 l/h........................ 29 

Portable Gas-Sampler with dry running rotary vane vacuum pump ............................................. 29 

ITES - an automatic control unit for isokinetic sampling of particulate matter, gases, PM 2.5/10 and dioxin 

sampling. ....................................................................................................................................... 30 

Zambelli ISODUST and ISOSPEED................................................................................................... 30 

Gas-tight corrosion resistant dry running rotary vane .................................................................. 30 

Double diaphragm pumps KNF ...................................................................................................... 30 

Temperature-resistant and heated pumps ................................................................................... 31 

KNF LABOPORT® Mini Diaphragm Vacuum Pumps and Compressors .......................................... 31 

KNF Chemical Resistant Vacuum Pumps ....................................................................................... 31 

Ejector for suction ......................................................................................................................... 31 

Dry-Gas-Meter ............................................................................................................................... 31 

Accessories for flowmeter and isokinetic control unit .................................................................. 32 

Accessories for flowmeter and isokinetic control unit .................................................................. 33 

Washing Bottles, Carrying box , Connecting flange ................................................................................. 34 

For gas sampling with bubbler must use a heated suction tube with direct connection to the bubbler. 

....................................................................................................................................................... 34 

Matching clamps for KS 19 ............................................................................................................ 35 

Carrying box for the washing bottle .............................................................................................. 35 

Connecting flange .......................................................................................................................... 35 

Strain relief for bubblers................................................................................................................ 35 

Flow Measurement ................................................................................................................................................... 36 

Pitot Tubes ..................................................................................................................................... 36 

S-Pitot Tube ................................................................................................................................... 36 

Cylindrical Pitot Tube ..................................................................................................................... 36 

Accessories for the emission sampling lines .............................................................................................. 37 

Vacuum hose ................................................................................................................................. 37 

hose clamp Stainless Streel ........................................................................................................... 37 

Quick release hose connector ....................................................................................................... 37 

Hose connector .............................................................................................................................. 37 

Quick release hose connector 6k-3/4 ............................................................................................ 37 

Hose connector .............................................................................................................................. 37 

Seal for big coupling ...................................................................................................................... 37 

Double-Coupling ............................................................................................................................ 38 

Male Plug with thread G ¾ ............................................................................................................ 38 

Closing Cap for big coupling .......................................................................................................... 38 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


4

Plan filter holder ............................................................................................................................ 38 

Plane filter, material: quartz fibre ................................................................................................. 38 

Plane filter from glass fibre (100 pcs) ............................................................................................ 38 

Petri glasses for plane filter holder ............................................................................................... 38 

Tinplate box for plane filter holder ............................................................................................... 38 

Transport Suitcase ......................................................................................................................... 38 

Filter husk ...................................................................................................................................... 39 

Titanium cone ................................................................................................................................ 39 

Filter thimbles type Gothe (25 pcs) ............................................................................................... 39 

Transport glasses ........................................................................................................................... 39 

Suitcase .......................................................................................................................................... 39 

cartridge for plug with glass fibre for high dust filter device ........................................................ 39 

Dust collector for cyclone .............................................................................................................. 39 

Quartz wool ................................................................................................................................... 39 

Glass wool 1000 g, superfine ......................................................................................................... 40 

Gas Wash Bottles PFA. PTFE ......................................................................................................... 40 

Bottles for Gas Wash Bottles ......................................................................................................... 40 

Gas Wash Bottle Adapters ............................................................................................................. 40 

Rettberg Gas Wash Bottle ............................................................................................................. 40 

Gas Washing Bottle PP .................................................................................................................. 40 

Glas Gas wash bottles 100mL/250mL, .......................................................................................... 40 

Gaskets with PTFE wall for GL screwcap ....................................................................................... 40 

Hose connectors in PTFE ............................................................................................................... 40 

Low-cost acrylflowmeters ............................................................................................................. 41 

Different flowmeters ..................................................................................................................... 41 

Rotameter ...................................................................................................................................... 41 

Rotameter up to 4,1 m³/h ............................................................................................................. 41 

Seal, Gasket ................................................................................................................................... 42 

Packing cord................................................................................................................................... 44 

Spacer with seal ............................................................................................................................. 44 

inner tube/liner for suction tubes ................................................................................................. 44 

Closing cap for ............................................................................................................................... 44 

Sealing plug for ½ female thread ................................................................................................... 44 

Adapter for filterhead .................................................................................................................... 44 

Adapter for threads ....................................................................................................................... 44 

Connection part KS 19 ................................................................................................................... 44 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


5

Connecting Part with integrated Thermocouple ........................................................................... 45 

Substitute Part ............................................................................................................................... 45 

Adapter for suction tubes with exchangeable inner tube ............................................................. 45 

Front adapter for suction tubes with fixed inner tubes. ............................................................... 45 

Stuffing gland ................................................................................................................................. 45 

Gas distributor: .............................................................................................................................. 45 

KS-19 ball for gas distributor ......................................................................................................... 45 

Hose nozzle for gas distributor ...................................................................................................... 45 

Closing cap for gas distributor ....................................................................................................... 45 

Temperaturmessgerät Mini-K (-64 bis +1370 °C). ......................................................................... 46 

Temperature controller ................................................................................................................. 46 

Jacket thermoelement, NiCr-Ni (Type K), ...................................................................................... 46 

Transmitter for thermocouple....................................................................................................... 46 

Heated sampling line ..................................................................................................................... 46 

PTFE tube / Teflon Hose ................................................................................................................ 47 

Swagelok couplings........................................................................................................................ 47 

Tripod to support probes .............................................................................................................. 47 

Maintenance Kit for suction pump ................................................................................................ 47 

Ritter high accuracy wet (drum-type) gasmeter ........................................................................... 47 

ABS-N/ABJ-NM, with high-quality single-cell weighing system and EC type approval [M] .......... 48 

Vacuum Desiccator MOBILEX 'ready to use' ................................................................................. 48 

Auto-Desiccator Wall, PMMA ........................................................................................................ 48 

Memmert Vacuum Ovens VO Series ............................................................................................. 48 

Manometer / Barometer ......................................................................................................................................... 49 

Digital manometer Greisinger GDH 200-13 ................................................................................. 49 

Digital barometer Greisinger GPB 3300 ........................................................................................ 49 

Watproof pressure handheld device with 2 sensor connection, analog output and data logger GMH 5155 

....................................................................................................................................................... 49 

testo 435-4 - multi-function measuring ........................................................................................ 50 

testo 417 - Vane Anemometer ...................................................................................................... 50 

The Airflow Instruments Velocity Meter TA440-A ..................................................................... 50 

Höntsch very robust rotary vane anemometer ............................................................................. 50 

Gas analyzers ............................................................................................................................................................. 51 

Testo 350 ....................................................................................................................................... 51 

testo 340 4-Gas Combustion Analyzer .......................................................................................... 51 

JNOX NO2 to NO Converter ........................................................................................................... 51 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


6

gas conditioning and sampling .......................................................................................................................... 52 

JCM Gas Cooler .............................................................................................................................. 52 

JC 14 and JC 24 Peltier Cooler ....................................................................................................... 52 

M&C GAS COOLERS, CONDENSATE REMOVAL AND SEPARATORS................................................ 52 

M&C GAS CONDITIONINGS PORTABLE, FOR MAX. 350NL/HR ...................................................... 52 

M&C OXYGEN ANALYSERS PMA 10 230V ...................................................................................... 52 

Tailor made case for analyser ........................................................................................................ 52 

WORKPLACE ATMOSPHERES MEASUREMENTS PERSONAL AIR SAMPLING PUMP AND 

STATIONARY PUMPS FOR SAMPLING FOR RISK MATERIAL MEASUREMENT ......................... 53 

GilAir Plus Personal Air Sampling Pump (1 - 5,000 cc/min) ........................................................... 53 

Gilian 5000 Personal Air Sampling Pump (20 - 5,000 cc/min) ....................................................... 53 

Gilian 800i Air Sampling Pump (200 - 800 cc/min) ........................................................................ 53 

Gilian GilAir-3 and GilAir-5 Air Sampling Pumps (0 - 3,000 / 0 - 5,000 cc/min) ............................. 54 

Gilian Gilibrator-2 NIOSH Primary Standard Air Flow Calibrator................................................... 55 

Accessories for WORKPLACE ATMOSPHERES measurements ...................................... 55 

KC adsorptiontubes ....................................................................................................................... 55 

Dräger Gas Detector Pump accuro® .............................................................................................. 56 

Rental equipment / used equipment ................................................................................................................ 56 

FID 3-200 (J.U.M.® Engineering) .................................................................................................... 57 

FID 3-100 (J.U.M.® Engineering) .................................................................................................... 57 

FID 3-300A (J.U.M.® Engineering) .................................................................................................. 57 

FID 109A (J.U.M.® Engineering) ..................................................................................................... 58 

Non Methane Hydrocarbon Cutter Modell 900 (J.U.M.® Engineering) ........................................ 58 

Prandtl Pitot Tube WITH ELECTRIC Pressure sensor (AIRFLOW) ................................................... 59 

Heated sampling line (Winkler) ..................................................................................................... 59 

SAMPLE GAS DILUTION Modell 108 (J.U.M.® Engineering) ........................................................... 59 

OXYGEN ANALYSERS PMA 10 (M&C TechGroup) .......................................................................... 60 

Portable or for wall mounting, compact, for max. 70Nl/hr .......................................................... 60 

Datenlogger COMBILOG LT 1021 (Theodor Friedrichs) ................................................................. 60 

Datenlogger LASCAR EL-USB-3 ...................................................................................................... 60 

Notebook ....................................................................................................................................... 61 

service / REPAIR OF FID analyzers JUM® ENGINEERING ..................................................................... 61 

calibration ...................................................................................................................................... 61 

Sand Test Instrument, ELEMENTAL ANALYZERS and surface measuring instrument ............ 62 

AREAMAT Specific Surface Area Determination of Solids ............................................................. 62 

Areameter Specific Surface Area Determination of Solid ............................................................. 63 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


7

thermostat for sample preparation Areamat / Areameter ........................................................... 63 

Accessories for BET Analysis .......................................................................................................... 63 

Accessories for BET Analysis .......................................................................................................... 64 

Sand Test Instrument .................................................................................................................... 65 

Gas permeability device GJ1 .......................................................................................................... 65 

Strength test instrument ............................................................................................................... 65 

Pneumatic Compactor CJ1 ............................................................................................................. 65 

pneumatic Ejector ......................................................................................................................... 65 

Agitator .......................................................................................................................................... 66 

CS1001 ........................................................................................................................................... 66 

the Hydrogen Analyzer special for aluminium and aluminium allo .............................................. 66 

spare parts and consumables ........................................................................................................ 66 

ELECTRIC STEAM GENERATOR STAINLESS STEEL ........................................................................... 67 

Fume cupboards / PATHOLOGY ........................................................................................................................ 68 

Fume cupboards STAINLESS STEEL ................................................................................................ 68 

Pathology ....................................................................................................................................... 68 

Laboratory Supplies / Laboratory Instruments You can find in oure ............................................ 68 

Laboratory Catalogue .................................................................................................................... 68 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


8

WE HAVE EVERYTHING FOR YOUR EMISSION SAMPLING TECH- 

NIQUE: 

SECTION DUST: 

Isokinetic Sampling according to EN 13284-1, EPA 5, ISO 9096 and VDI 2066 

We offer complete solutions for portable sampling lines to determine gravimetrical the dust load in flowing gases with filter device IN- and 

OUT-Stack. 

Filter device according to EPA-, ISO and VDI-Guidelines. 

easy handling 

range: 0,1..500.000 mg/m³ 

temperature range up to 1000°C 

length up to 6000 mm 

compliance EN, USA-EPA and VDI 

highest measuring accuracy 

automatic sampling system 

available: Inox and Titanium 

IN-Stack sampling: OUT-Stack sampling: In small ducts and pellet boilers: 

OUT-Stack Sampling according to EN 14385, EPA 5 (e.g. Heavy Metals & Mercury): 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


9

SECTION DIOXINS: 

Everything for PCDD/F sampling in flowing gases - EN 1948 

PCDD / PCDF (Dioxins / Furans) 

Cooled probe method according to EN 1948-1 and VDI 3499 part 3 

Easy handling. 

Can combine and modular extensible as required. 

Minimized glass damage by protection with Aluminium or PVC. 

Universal holder for the suction tube with support for tripod-poles for stabilizing. 

Tenon joints allows a quick assembly and disassembly of the unit. 

The condensate trap (GL 45 brown glass bottle) is cooled by either a cooling coil with cryostat or with ice bath. A wire mesh keeps the center 

free from ice, so that the condensate trap can insert easy. Radially around the cooling jacket can plugged in the adsorber units or the drop 

separator and connected with glass. 

After the condensate trap flows the gas through two adsorber with an interposed standard plane filter. For easy filling, the adsorber have a GL 

60 thread (opening Ø 50 mm) and can be sealed gas-tight for a contamination-free transport. 

SECTION PAH/PCB/TAR: 

System for the measurement of organic compounds 

Sampling line for PCB and PAH 

System developed from HLUG (Hessian Agency for the Environment and Geology) with cooled condensate trap and small double XAD adsorption 

trap. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


10

Measurement of TAR according to CEN/TS draft 15439 

Sampling line for the TAR determination 

Method: Sampling according to EN 13284-1, heated thimble filter, absorption through 6 bubbler in isolated inox box with two separate sections. 

Construction according to CEN/TS 15439. Last trap is one XAD-cartridge. 

Size of the inox box (length x wide x high): 430 x 245 x 320 mm. 

Probe for continuous gas sampling 

SECTION GASE: 

Heated Gothe-Gas Sample Probe 

Optimum operational reliability 

Universal applicability 

Easy installation 

Problem-free maintenance 

Small stagnant space 

Proven technology by Gothe 

The Gothe gas sample probes can use for continuous gas sampling in high dust content, temperatures and humidity. 

The probe can combine with one preliminary filter and a main heated filter with can change without dismounting the complete gas sample 

probe. Designed is this probe for easy installation, reliable operation, trouble-free maintenance and universal applicability. Depending on the 

application, different prefilters with G ½ thread and main filters can used. 

The main filter element is placed in housing with low stagnant space and can exchange with simple tools and it is not necessary to remove the 

sample line, thus avoiding contamination of the clean gas path and also maintaining the integrity of the system. 

The special high performance heating cartridge permits controlled heating of the complete filter housing and probe up to 300°C. This ensures 

reliable operation external to the process preventing the temperature falling below the dew-point, as requested 180°C in the Standard. The 

temperature is controlled by an integral compact design capillary sensor thermostat. The calibration gas can be injected in front of the filter to 

be sure that it has the same circumstance as the sampling gas. 

Filter Heater 

Electrical heated with high performance heating cartridge ~ 400 Watt (230 V), length: ca. 200 mm, Ø 110 mm, with isolation, Stainless Steel 

calibration gas connector: Swagelok 6 mm, Stainless Steel suction gas connector: Swagelok 6 mm with holder for heated sampling line. Material 

heater: Aluminum. Material in contact with gas: Stainless Steel (or Titanium). 

Suction Tube 

With Ø 25 mm, fixed inner tube with 6 mm internal diameter, entrance: internal thread G ½, electrical heated with high performance heating 

cartridge (~ 400 W), material: Stainless Steel or Titanium, length: 1000 mm, 1500 mm or 2000 mm. 

Temperature Controller 

Temperature setting: 50..300°C, with 10°C increments. The controller is mounted at the heater in one aluminum box with switch signal lamp. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


11

Sampling lines for the determination of HCl, HF, etc. - EN 1911 

SECTION ACIDS: 

Isokinetic Sampling according to EN 1911 

We offer you complete solutions for the determination of hydrochloric or hydrofluoric and similar acids according to EN 1911 with heated filter. 

easy handling, range: 0,1..500.000 mg/m³, temperature range uo to 1000°C, length up to 6000 mm, compliance VDI, EN, USA-EPA, highest 

measuring accuracy, automatic sampling system, available: Inox and Titanium 

Sampling line with bubbler: 

For the determination of HF (gaseous fluorides) should use MONEL 400 (special steel) in accordance with ISO 15713-2006. 

The fragile quartz-nozzles must not longer used. 

For our customers: MONEL 400 gooseneck nozzles and inner-tubes (liner) matching to the Gothe suction tube. 

SUCTION PYROMETER 

GAS TEMPERATURE MEASUREMENTS WITH SUCTION PYROMETER ACCORDING TO 

IFRF (INTERNATIONAL FLAME RESEARCH FOUNDATION) AND VDE: 

Gas Temperature Measurements with Suction Pyrometer according to IFRF (International Flame Research Foundation) and VDE: 

For the determination of the temperature in the afterburning zone should be measured only the convective component of heat and not the 

radiative exchange between the thermocouple and its surroundings. For such measurement you need our robust suction pyrometers. The 

thermocouple is located in the front area of the probe and is shielded by a ceramic body and shielded against the IR radiation from the combustion 

chamber. The gases are drawn between the shields and over the thermocouple with high velocity (> 80 m/s ) so that the equilibrium 

thermocouple temperature is the gases temperature without the need for correction. The suction probes are fully jacketed and cooled. The 

sucked and cooled gas can use for oxygen measurement. The special bayonet coupling at the front of our pyrometer allows rapid exchange of 

broken ceramics. 

Application for temperatures up to 1600°C. . 

Pyrometer optional with two ceramics (front open) according to VDI / VDE or according to IFRF with three complete closed ceramics. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


12

GAS VELOCITY - FLOW 

GAS VELOCITY - FLOW EQUIPMENT FOR AIR AND GAS SPEED MEASUREMENT WITH PITOT TUBES 

Pitot tubes 

With Pitot tubes and difference pressure sensors can you measure very easy the gas pressure, velocity and volumetric flow. Unlike nozzles 

and orifice the pitot tubes cause in pipe lines no significant pressure loss. They are largely independent of position. Differences between the 

flow direction and the axis of the pitot tube head up to 15° practically do not affect the measurements. 

In general, pitot tubes are combinations of two tubes, one for total pressure and one for the static pressure. The difference between these 

pressures is the dynamic pressure. This dynamic pressure is in relationship with the gas density and velocity. By knowing of the gas density 

can you calculate very easy the velocity. 

The Pitot tube measurement with our high-precision micromanometers allows for much more accurate readings than other methods. Moreover, 

you must have only a relative small hole in the duct wall to allow at all times quick measurements. 

Prandtl-Pitot Tube S-Pitot-Tube Cylindrical Pitot Tube (probe according to VDEh) 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


13

PROBES / NOZZLES FOR THE ISOKINETIC SAMPLING 

GOOSENECK-CURVE WITH INTERCHANGEABLE NOZZLES 

includes a set of 5 nozzles and one gooseneck-curve for small tubes and openings (openings > G 2½). Total leg length 

(curve with nozzle): 77 mm, nozzle openings: 6, 8, 10, 12 and 14 mm. Complete in a small plastic-suitcase. Nozzle exit and 

entrance gooseneck-curve with screw thread M 12. Exit gooseneck-curve: external screw thread G ½. 

NOZZLE FOR GOOSENECK BENT 

Openings available from 4 - 24 mm, up to 14 mm in combination with gooseneck bent for small opening 3''. 

Or with special gooseneck bent for opening 2½''. Exit: Internal thread M 12 

Material: Stainless-steel or titanium 

GOOSENECK-CURVE WITHOUT NOZZLE 

(for nozzles according to European Standard EN 13284-1, total leg length (curve with nozzle): 77 mm, entrance gooseneckcurve: 

thread M 12 x 1, exit: external thread G ½, material: stainless-steel 

Nozzles according to VDI 2066, page 2 and EN 13284-1, 

Openings available from 6 - 30 mm, 

length: appr. 68 mm, 

Exit: External thread G ½ 

NOZZLES ACCORDING TO VDI 2066, PAGE 2 AND EN 13284-1 

material: stainless-steel up to 500°C, 1.4841 up to 1000°C or titanium up to 400°C 

BENT FOR NOZZLES 

Bent for nozzles, bent R = 25 mm, tube 10 x 1 mm, 

Entrance: Internal thread G ½, 

Exit: External thread G ½. material: stainless-stell or titanium 

GOOSENECKNOZZLE ACC. EN 13284-1 UND ISO 9096: 

Goosenecknozzlefor 

small openings, acc. ISO 9096, nozzle opening from 4 to 14 mm availiable with leg length 51 mm, exit: external thread 

G ½, tube: 10 x 1 mm. material: stainless-stell or titanium 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


14

NOZZLES ACCORDING TO VDI 2066, PAGE 7 AND EN 13284-1: 

Nozzles according to VDI 2066, page 7 and EN 13284-1: 

with exit G ¾, conical, only for plane-filter-device acc. VDI 2066, page 7 and impactor, 

nozzle diameter 2 - 18 mm available, length: 39-59 mm 

FILTER DEVICE FOR DUST- AND AEROSOL SAMPLING (TSP) 

PLANE FILTER DEVICE FOR DUST RANGE UP TO 50 MG/M³ ACCORDING TO VDI 2066 AND EN 13284 

Plane filter device for dust range up to 50 mg/m³ according to VDI 2066 and EN 13284 

or IN- and OUT-Stack-Sampling (absolute: 20 mg). for Ø 37, 45, 47 and 50 mm plane filter. 

material: stainless-stell or titanium 

ACCESSORIES FOR PLANE FILTER 

product 

Nozzles according to VDI 2066, page 2 and EN 13284-1 

Plan filter holder 

Bent for nozzles 

Plane filter from quartz fibre (25 pcs) 

Petri glasses for plane filter holder 

Plane filter from glass fibre (100 pcs) 

Transport Suitcase 

Self-regulating small heater for filter device 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


15

Plane filter device 

PLANE FILTER DEVICE PECIAL FOR VERY LOW DUST RANGE (< 5MG/M³) CONSTRUCTION 

ACCORDING TO VDI 2066, PAGE 7 PAGE 8 AND EN 13284 

special for very low dust range (< 5mg/m³), for IN-Stack-Measurements. 

Construction according to VDI 2066, page 7 page 8 and EN 13284. The probe is contructed cylindrically and smoothly fitted to 

the diffusor of the filter device with an aperture angle of 30°. Maximum gas flow rate: 4 m³/h, adsorption capacity of particulate 

matter (approximate value): 20 mg. Max. sampling flow rate: 4 m³/h, three-parts, incl. one plane filter holder with circle-ringgrooves 

and seals, without nozzle. 

Entrance: Internal thread G ¾ 

Exit: External thread G ½. for Ø 45 mm plane filter Outer diameter: 55 mm, Length: 81 mm 

product 

ACCESSORIES FOR PLANE FILTER ENTRANCE: INTERNAL THREAD G ¾ CONICAL. 

Nozzles according to VDI 2066, page 7 and EN 13284-1: 





SIMPLE TUBULAR FILTER DEVICE 

Simple tubular filter device for dust range from 20 to 1000 mg/m³, for IN- and OUT-Stack-Measurement. 

Construction according to VDI 2066 and EN 13284. (absolut 1-2 g), construction according to VDI 2066, page 2 (1981), 5-parts with 

filter bush. 

Separator with a filtering bush (bush stuffed with quartz wool or with quartz thimbles). 

Max. sampling rate: 4 m³/h, incl. one bush with cone, seal, without nozzle. 

Entrance: Internal thread G ½ Exit: External thread G ½ . 

Size: Outer diameter: 45 mm, Length: 145 mm. Material: stainless-stell or titanium 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


16

ACCESSORIES FOR SIMPLE TUBULAR FILTER DEVICE 

product 

Filter husk 

Titanium cone 


Filter thimbles type Gothe (25 pcs) 

Quartz filter thimbles type Gothe (25 pcs) 

Transport glasses 

Suitcase 

Glass wool 1000 g 

Quartz wool 500 g 

HIGH PRECISION TUBULAR FILTER DEVICE FOR DUST RANGE FROM 20 BIS 2000 MG/M³, WITH BACK 

UP PLANE FILTER (Ø 45 MM). ACCORDING TO VDI 2066 AND EN 13284 

Tubular-Plane-Filter-Device 

Filter device for IN- and OUT-Stack-Measurements. Construstion according to VDI 2066, page 2 and EN 13284. (absolut 1-2 g), 

construction according to VDI 2066, page 2 (1983), 8-parts with filter bush and plane filter holder (Ø 45 mm). Separator with a 

filtering bush (bush stuffed with quartz wool or with quartz thimbles). A plane filter (Ø 45 mm) following the bush filter retains broken 

fibres from the bush which may occur during the measurement. By this the detection limit of the gravimetric mass determination 

is reduce and the reproducibility of the measurement is enhanced. The separator consist of the filter housing and the filter. 

Max. sampling rate: 4 m³/h, incl. filter bush with cone, plane filter holder, seal, without nozzle. 

Entrance: Internal thread G ½ Exit: External thread G ½. 

Outer diameter: 55 mm, Length: 145 mm. Material: stainless-stell or titanium 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


17

ACCESSORIES FOR HIGH PRECISION TUBULAR FILTER DEVICE FOR DUST RANGE FROM 20 BIS 2000 

MG/M³, 

product 

Filter husk 

Titanium cone 

Filter thimbles type Gothe (25 pcs) 

Quartz filter thimbles type Gothe (25 pcs) 



Suitcase 

Glass wool 1000 g 






Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


18

HIGH DUST TUBULAR FILTER DEVICE FOR DUST RANGE UP TO 100 G/M³ ACCORDING TO VDI 2066 

AND EN 13284. 

High dust tubular filter device 

The dust is separated either by the bush plugged with glass-fibre wool or by inserting a Munktell glass-fibre thimbles. Three-part 

filter out of stainless steel, housing outside: Ø 70 mm, length: approx. 240 mm with union nut: Ø 80 mm, including a metal socket to 

plug with glass-fibre or quartz wool. Metal socket internal Ø: 56 mm, length: 150 mm, out of high-grade steel with high-grade steel 

filter base 

Entrance: union nut G ½, Exit: external thread G ½ 

Outer diameter: 70 mm, Length: 240 mm 

ACCESSORIES FOR HIGH DUST TUBULAR FILTER DEVICE 

product 

Glass fibre thimbles for high dust tubular filter (25 pcs) 

cartridge for plug with glass fibre for high dust filter device 

Adapter for Threads 

Matching basket for high dust filter device 

Cyclone Separator 

STAINLESS STEEL CYCLONE SEPARATOR FOR DUST RANGE UP TO 500 G/M³ 

Cyclone made of stainless steel, can be attached in front of and behind the suction tube. Separating performance: particles > 

5 µm, Area of application: up to 650°C. Dust collector with thread (75, 150 and 500 cm³), Suction rate: > 3.5 m³/h, 

Entrance: Internal thread G ½ 

Exit: External thread G ½ 

In the delivery capacity: cyclone without dust collector and without heater. 

Drawing: Trajectories for Gothe cyclones. Conditions: 3.5 m³/h, T: 180°C 

Green curve: trajectory for particles with diameter of 5 µm (CFX-simulation). 

ACCESSORIES FOR CYCLONE SEPARATOR 

product 

Dust collector for cyclone 

Heater for cyclone 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


19

PLANE FILTER DEVICE FOR PLANE FILTER Ø 110 MM FOR DUST RANGE UP TO 2000 MG/M³. 

Plane filter device for plane filter Ø 110 mm for dust range up to 2000 mg/m³. 

Plane filter holder for plane filter Ø 110 mm. Non heated and heated version (two ring heater cartridges (150 Watts, 230 V). 

Entrance: Union nut G ¾. Exit: External thread G ¾. 

DUST FILTER FROM DURAN OR QUARTZ GLASS FOR SPECIAL APPLICATION 

Dust filter from Duran or Quartz Glass for special application 

Pre dust filter 

Tubular-Glass-Dust Filter, two-parts, made of glass or quartz as dust separator for gas analysis, 

for dust range 5 .. 1000 mg/m³. 

Plane-Glass-Dust Filter, three parts, made of Duran or Quartz glass as dust separator with plane filter Ø 50 mm. 

PRE DUST FILTER 

Filter device for stuffing with wool to protect the sampling line for coarse dust. 

This filter can place in front of the suction tube. Material: Titanium 

SMALL SAMPLING EQUIPMENT ACCORDING TO EN 13284-1 AND ISO 9096 

Small sampling equipment according to EN 13284-1 and ISO 9096 

Functional sampling set for high precision dust monitoring at low range (< 20 mg/m³) and high range (< 1000 mg/m³). 

Complete in one stable plastic suitcase (255 x 210 x72 mm) with fitted PU-foam. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


20

HEATER FOR FILTER DEVICE OUT OF ALUMINUM HALF-PIPES. 

THE HALF-PIPES ARE UNFOLD AND THUS PERMIT FREE ACCES 

TO THE FILTER DEVICE. NOW THE HOT SECTIONS CAN BE RE- 

MOVED TROUBLE-FREE BY MEANS OF THIN SPANNERS. 

Small heater 

SMALL HEATER 

After opening, the small heating can completely be removed. All filter devices fit into the small heater. This heater is folded 

around the end of the suction tube. Electrical performance: Cartridge ~ 200 Watt, 230 V, Size: Ø 110 x 150 mm with thermocouple 

(NiCr-Ni) with 2 m cable for NiCr-Ni and 2 m power supply cable. 

Large heater 

LARGE HEATER 

The large heater serves filter devices with gas distributor. The heater is fastened to the suction tube by means of a 

flange and stabilizes the internal parts. At the back of the heater can mounting a carrying box for bubblers. Heater 

cartridge: ~ 400 Watt , 230 V. Weight: 3 kg. Shape: Aluminium-square tube: 120 x 120 x 285 mm, with 5 mm thick 

thermal mineral fibre insulation. In the delivery capacity: 5m cable for NiCr-Ni and power supply. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


21

ACCESSORIES FOR HEATER 

product 

Gas distributor 

KS-19 ball 

Hose nozzle for gas distributor 

c 

Temperature controller 

Self-regulating small heater for filter devices 

SELF-REGULATING SMALL HEATER FOR FILTER DEVICES 

Electrical heated, with powerful cartridge heater ~ 220 Watt (230 V), length ca. 155 mm, Ø 110 mm, matching for all filter devices, 

with built in temperature sensor, material: Aluminium. Controlling with built in temperature sensor at the heater. The heat 

controller is flanged at the Aluminium-housing. Selectable tremperature range: 50 .. 300°C, scale: 10°C with knob at the front 

plate aluminium-housing. 

ACCESSORIES FOR SELF-REGULATING SMALL HEATER 

product 

Gas distributor 

KS-19 ball 




Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


22

TEMPERATUR CONTROLLER FOR THE HEATER 

Temperature controller for all filter heater and all electrical heated suction tube with integrated thermocouple NiCr-Ni. 

Temperature controller for all filter heater and all electrical heated suction tube with integrated thermocouple NiCr-Ni. 

Housing from Makrolon, for thermocouple NiCr-Ni, with permanent digital 3-digit reading of the actual temperature. The 

scanning rate of the signal processing is 120 ms with a resolution of 10.000 points. There is one output for heater with 

exchangeable relay for resistive load (5 A fuse, 230 V) with status-LED. Control structure: ON/OFF, P, PI, PID - heating; self-optimization, 

adaptive optimization and alarm functions. Switchable to manual heating (impulse heating without thermocouple). 

Voltage: 210-240 VAC. Resistive load: 5 A. Operating temperature: -10 to 50°C 

ACCESSORIES FOR TEMPERATURE CONTROLLER 

product 

Filter device heater 

Electrical heated suction tube 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


23

GLASS- AND QUARTZ FIBRE FILTER 

Plane filter from glass- and quartz fibre 

PLANE FILTER FROM GLASS- AND QUARTZ FIBRE 

Both varieties have a high heavy metal purity. Fiberglass are stable to 500°C and without a binder. 

The quartz fiber can use up to 900°C and is without binder and can use for applications for heavy metal analysis 

and gases with high sulphur dioxide concentration. 

Plane filter holder Material: stainless-stell or titanium 

PLANE FILTER HOLDER 

with circle-ring-grooves and fixing ring for the plane filter device. 

Petri glasses for plane filter holder 

with lower part and cover from glass: 

PETRI GLASSES FOR PLANE FILTER HOLDER 

Tin box Ø 70 mm for plane filter holder Ø 45-50 mm, innerdiameter: 70mm, high 22 mm, weight: 29,3 g. 

Easy opening and closing by solid push-mechanism. 

Transport suitcase for plane filter holder 

TRANSPORT SUITCASE FOR PLANE FILTER HOLDER 

made of plastic with handle for save and contamination free transport. The filter holders are transported lying and can take 

out easy without any loss of filter material, matching for 8 petri-glasses. 

Glass-fibre / Quartz fibre thimbles for tubular filter device 

FILTER THIMBLES FOR TUBULAR FILTER DEVICE 

Tubular filter thimbles for high dust concentration up to 2 g/m³. Both varieties have a high heavy metal purity. Fiberglass are 

stable to 500°C and without a binder. The quartz fiber can use up to 900°C and is without binder and can use for applications 

for heavy metal analysis and gases with high sulphur dioxide concentration. 


QUARTZ WOOL 500 G 

for stuffing the Titanium or Stainless Steel husk for the dust sampling. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


24

FILTER HUSK FOR TUBULAR FILTER DEVICE 

Filter husk 

The husk should be stuffed with wool or with thimbles, length: 68 mm. Generally employ a cone when using glass- or quartzthimbles. 

The cone guarantees that the gas flow moves into the thimble and not past it. In the Stainless Steel and Titanium husks 

fit glass fibre and quartz fibre thimbles. The Stainless Steel and the Titanium cone is for the glass- and quartz fibre thimbles from 

company Munktell. 

Cone for filter husk 

CONE 

It is not necessarry to conditioning the cone with the single glass- or quartz fibre thimble (2-3 cones are sufficient for all samplings) 


TRANSPORT GLASSES 

for filter husk, glass with thread and cover 

Suitcase for transport glasses 

SUITCASE FOR TRANSPORT GLASSES 

for safe and free of contaminations for 8 transport glasses. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


25

SUCTION TUBE / PROBE FOR ISOKINETIC SAMPLING 

COMBINATION - PROBE: NON HEATED, ELECTRCAL HEATED OR WATER COOLED Ø 60 MM 

The combination probe is an advancement of the standard suction tubes. For a better isokinetic sampling. A Pitot tube and a thermocouple 

type K (NiCr Ni) are inserted into the outer tube. Both are installed parallelly to the inner tube. The flow rate and the temperature can be determined 

by this arrangement directly at the sampling point. Standard delivery with one S-Pitot Tube (easy to change by cutting ring screw 

connections, on request with Prandtl Pitot tube). The combination probe can be produced in Stainless Steel or Titanium, Version: non heated, 

electrical heated or water cooled, with exchangeable inner tube 10 x 1 mm. 

Heated Combiprobe: 

Cooled Combiprobe: 

Standard Combiprobe: 

Non heated probe Ø 25 mm 

NON HEATED PROBE Ø 25 MM 

with fixed inner tube 10 x 1 mm and with G ½ thread and quick release hose connector. Available in Stainless Steel, 

Special Steel ( 1.4841) and Titanium, outer-Ø: 25 mm 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


26

ELECTRICAL HEATED PROBE Ø 25 MM 

Electrical heated probe 

with integrated thermocouple for the heater regulation (NiCr-Ni). 

Quick-release hose connector, outer-diameter: Ø 25 mm. 

Heater cartridge (~ 500 W / m). 


Exit: External thread G ½. 

with fixed inner tube or with exchangeable inner tube 

Available in Stainless Steel, or Titanium, 

For the suction tube must order the matching adapter for the front (see accessories) 

Dont forget to order the inner tube for version with exchangeable inner tubes: Matching inner tubes see accessories. 

HEATED POWER-PLANT-PROBE WITH INTEGRATED HEATED FILTER IN FRONT OF PROBE Ø 64 / 60 

MM 

Heated Power-Plant-Probe 

The probe can be used in power plants with high concentration of sulphuric acid droplets in the flue gas. One 

exchangeable plane filter holder is in the front of a heated probe. Around of this plane filter holder and the 

conical entry is winding a second high performance heater cartridge. This avoids condensation at the filter 

(gas temperature above dew point, measured with a thermocouple in the gas stream). At the exit can screwed 

extensions. The filter can be heated above the dew point of the sulphuric acid and avoid wrongness dust 

measurement. Because the collected sulphuric acid droplets on the filter can sham up to 10 mg/m³ dust. 

Water cooled suction tube (Universal Probe) 

WATER COOLED SUCTION TUBE (UNIVERSAL PROBE) 

water cooled suction tube for exchangeable internal tube 10 x 1 mm, outerdiameter: 

Ø 33 mm. 

The cooling water would be guided along the inner tube, turned round and flows along the outside wall. By glassbreak 

of the inner tube, the individual parts can be removed over the rear internal thread G ¾. With sufficient water cooling, this suction tube 

can be used at temperatures up to 1000° C. 

If a hot-fan used instead of cooling water (adapters not in the delivery capacity) can the suction tube be heated. 


Exit: External thread G ½. 

Available in Stainless Steel, or Titanium, 

Necessary accessories for version with exchangeable inner tubes: 

Matching inner tubes see accessories. 

An adapter at the front is required (see accessories) 

GAS SAMPLE PROBES 

GAS SAMPLE PROBES 

Portable gas sample probe type PSP4000-H. With external ceramic filter type S-2K, filter porosity: 2µm. Electrically heated 

external filter 100-180°C adjustable by an incorporated thermostat. 7-pin plug with 4m connection cable and mains plug. 

Incl. mounting clamp for heated sample line. Gas inlet: G3/8"i, gas outlet: G1/8"i with tube connector 6mm. Power: 

230V/50Hz, 200W. Material: SS316, ceramic, Viton. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


27

ACCESSORIES FOR SUCTION TUBE / PROBE FOR ISOKINETIC SAMPLING 

product 

inner tube / liner for suction tubes Inner tube, 10 x 1 mm, material:Titanium for suction tubes with exchangeable inner tubes 

Front adapter for suction tubes with exchangeable inner tubes. Adapter to fixed the bent at suction tubes without integrated 

internal tube, entrance: screw cap G ½, exit: external thread G ½ with hole for tube 10 x 1 mm. Material:Titanium and Stainless Steel. 

Adapter for probe with fixed inner tube to fixed the bent for suction tubes with fixed internal tube 10 x 1 mm Entrance: Screw cap G 

½ Exit: External thread G ½, Material: Titanium and Stainless Steel. 

Spacer (Stainless Steel) with seal (rubber) for inner tube for cooled suction tube. 

Stuffing box for suction probe with exchangeable inner tube to fix the inner tube in the suction probe, thread G ½. Material: Titanium 

and Stainless Steel. 

Packing cord to seal the holder and the inner tube from the suction tube 

Packing cord Mineral fibre graphitized: Ø 4-5 mm, temperature resistance up to 500° C, Unit: Meter, Weight: ca. 50 g / meter, 

Packing cord PTFE: Ø 4 mm, temperature resistance up to 200° C, Weight: ca. 0,02 kg / m. Unit: Meter 

Packing cord PTFE graphitized: Net from PTFE-yarn with graphite and temperature-constant silicone-oil, temperature resistance up to 280° 

C Ø 4 mm, unit: meter 

Gas-tight holders 

Holder made of stainless steel for fixing the suction pipe at the measuring point. The gas-tight closure is achieved by a packing cord which 

is pressed against a flange on the suction pipe by means of screws. For shifting the suction pipe the flange is loosened. 

For suction pipes with external Ø: 25, 33, 50 or 60 mm, with external thread G 2, G 2½ or G 3. 

Sleeve reduction 

The holder can be adapted to the different coupling sleeves / sockets at the measuring points through sleeve reductions (bushing (M/F). 

The sleeve reduction is composed of stainless steel and an internal thread Variations: G 3 to G 2 or G 2½ to G 2. 

Tube-Cleaning-Set 

Set consist of: Tube brush hard, micro abrasive Ø 8,2 mm (zink-coated wire with surface of nylon-alumina, grain 600) with 1000 mm tube to 

shove and fix it inside a cordless screwdriver, one extension-tube Ø 6 mm with thread, length: 1000 mm, one cleaning brush soft with nylon, 

Ø 10 mm (with wire to pull it through the tube). 

Tripod to support probes 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


28

PUMP, GAS METER, FLOWMETER AND ISOKINETIC CONTROL 

UNIT 

FLOW MEASUREMENT ADAPTED FROM STRÖHLEIN 

Complete equipment for volume measurement in carrying system: The system consists of a carrying-system condensate 

bottle, drying tower, vacuum-gauge: 0- 400 mbar, thermometer, rotameter (0 to 4.1 m³ / h) and gas volume meter BK G6 

Complete equipment for volume measurement in carrying system 

MANUAL UNIT FOR VOLUMETRIC DETERMINATION 

Carrying-system (stable construction with holder and mountings from high-quality stainless steel), big drying-tower with 

water-separator (Art.-No. 16.011), gas volume meter with vacuum-gauge and thermometer, rotameter and hoses. All hoseconnections 

are equipped with quick connector. 

COMPACT AND ROBUST GAS-SAMPLER WITH CP-MODUL FOR GAS SAMPLING UP TO 320 L/H. 

Kompakter und robuster Gasprobennehmer mit CP-Modul 

In a carrying-system: drying tower, valve for the volume flow rate, flowmeter, range: 30-360 l/h, membrane pump, gas 

meter with thermometer. The integrated Gothe CP-Modul hold constant the adjusted gas flow also if the pressure change. 

E.g. 200 l/h adjusted by needle valve will be constant, if the pressure drop behind a filter increase from initially 50 mbar to 

250 mbar vacuum. 

PORTABLE GAS-SAMPLER WITH DRY RUNNING ROTARY VANE VACUUM PUMP 

Portable Gas-Sampler with dry running rotary vane vacuum pump 

for gas sampling up to 2,5 m³/h. In a carrying system (transportation frame, material: stainless-steel-square-tube 15 x 15 

mm with handle) are: one drying tower (material: PVC, dimensions: Ø 75 mm x 170 mm), space for silicagel: 0,9 l, volume 

water separator: ca. 0,5 l one rotameter 0,2 .. 2,5 m³/h (scale 0,1 m³/h standard condition.) one dry running rotary vane 

vacuum pump (performance: 3 m³/h, vacuum: 800 mbar, 230 V/ 0,12 kW) one stainless steel regulation valve one dry gas 

volume meter (0,04 .. 6 m³/h, accuracy 2% with certificate) with thermometer (0..60°C, scale 1°C). one pulsation dumper 

with filter behind pump. Dimensions: ~ 340 x 340, high: ~ 450 mm, weight ~14 kg. The pump starts manually. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


29

ITES - AN AUTOMATIC CONTROL UNIT FOR ISOKINETIC SAMPLING OF PARTICULATE MATTER, GA- 

SES, PM 2.5/10 AND DIOXIN SAMPLING. 

ITES Automatic Isokinetic Sampler 

The ITES is an automatic control unit for isokinetic sampling of particulate matter, gases, impactor and dioxin sampling. 

The system consists of three separate units: 

- an intelligent controller with integrated calibrated orifice 

- case with external sensor for pitot tube and thermocouple placed at the probe 

- high performance frequency controlled pump with by-pass valve (SB 6: 5 m³/h). 

Sampling according to EN, ISO and VDI-Standards. Complete software controlled from standard laptop, 

developed for Windows 2000, XP, Vista and 7. 

In the delivery capacity: frequency controller, external sensor, gas tight and corrosion resistant dry running 

rotary vane vacuum pump SB 6, 3 m cable pump-controller, 5 m cable external sensor-ites, 5 m cable controller-laptop, 2 m power cable. The 

laptop is not in the delivery capacity 

Technical features: 

Difference pressure 

0,01..10 hPa (+/- 0,02 hPa) (on request other ranges possible) 

Absolute pressure 

400 .. 1300 hPa (+/- 0,2 % final Value) 

Temperature duct NiCr-Ni 

0 .. 500° C (+/- 0,4 % final Value) (on request other ranges possible) 

Operating temperature 

-10 .. 60° C 

Alarm output 

12 V 

Supply 

230 VAC, 50 Hz 

Orifice 0,5 .. 4 m³/h (>1m³/h with accuracy

TEMPERATURE-RESISTANT AND HEATED PUMPS 

KNF Temperature-resistant pumps can transfer air as well as neutral or aggressive gases at temperatures up to 240 °C. In order to prevent 

condensation of the measuring gas, the heated head pump types possess temperature-resistant pump head components 

and optional thermostatic or electronic temperature control. 

Vacuum Pumps and Compressors 

KNF LABOPORT® MINI DIAPHRAGM VACUUM PUMPS AND COMPRESSORS 

Diaphragm vacuum pumps and compressors are dry-running devices used in a wide range of laboratory applications. They 

transfer, compress and evacuate different types of air, gases and vapors without contamination. The pumps are used for 

various laboratory applications such as vacuum distillation, multiflask filtration and gel drying. 

KNF CHEMICAL RESISTANT VACUUM PUMPS 

KNF LABOPORT® is the name of our chemically resistant diaphragm vacuum pump line for aggressive media. These pumps can be used to 

transfer and evacuate almost all laboratory gases and vapors. They are characterized in particular by the use of resistant 

materials such as all-round PTFE for the pump head, FFPM for the valves, and KNF's structured diaphragm with a PTFE 

coating. 

Ejector for suction 

EJECTOR FOR SUCTION 

Ejectors are suitable for the suction by means of compressed air. The delivery volume depends on the pressure of the 

compressed air and the reduced pressure at the suction side. The delivery includes a pressure-reducing valve with compressed-air 

link and pressure indication, a sleeve valve at the suction side for adjusting the suction volume and a sound 

absorber. Compressed-air link: quick-coupler, suction side: quick-coupler. 

Gaszähler BK4 oder BK6 

DRY-GAS-METER 

Resistant and durable finish (interior parts out of plastic). Operating temperature: -20 to 60°C, limits of calibration errors: 

from 0,2 Qmax: 1.5 %, 

BK 4 Range (Q): 0,04 m³/h bis 6,0 m³/h / BK 6 Range (Q): 0,06 m³/h bis 10,0 m³/h 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


31

ACCESSORIES FOR FLOWMETER AND ISOKINETIC CONTROL UNIT 

product 

Gas cooler with water separator for damp and vapour-saturated gases. The gas cooler is operated in front of the drying tower, in order 

to reduce the consumption of silica-gel. However, the application of a drying tower remains necessary. Developed for application on the spot: 

built extremely stable, with place to stand and cooling links. Completely with quick release hose connector. Out of a 2 mm stainless steel pipe. 

Composed of a cooling device and a water collecting vessel. 

Small gas cooler (Cooling pot: Ø 130 x 200 mm, approx. 3 m of cooling coil (tube 10 x 1 mm): 

Large gas cooler (Cooling pot: Ø 220 x 200 mm, approx. 3 m of cooling coil (tube 18 x 1.5 mm) 

Drying Tower for Silica-Gel 

Drying towers for drying the gas with silica-gel (or a comparable drying agent). For the protection of the gas meter from aggressive media and 

- by the water separating chamber - from condensation water and dust particles. In accordance with VDI 2066 and EN 13284-1 the volume 

determination can be referred to the dry operating condition. 

Small drying tower (PVC-tube, Ø 75 x 280 mm): 

Big drying tower ( PVC-tube, Ø 160 x 400 mm): 

Silica-Gel (2-3 mm) 8 kg in practical bucket, H2O- adsorption ~ 25-27 weight-%, 

Drying agent containing cobalt dichloride (weight-% 0,2-0,9; hazard symbols: T, N; 

Drying tower Ströhlein 

Drying tower Zambelli 

Pulsation damper ITES Ø 75 mm, ca. 200 mm long, incl. hose with hose plug and fast connector with hose plug. 

Bimetal Dial Thermometers VA 0+ 60°C for gasmeters 

Manometer 0…-400mbar or 0…-250mbar for gasmeters 

Suction hoses 

Woven hose 19 x 4 mm for vacuum, temperature range: -40 .. + 120°C. 

Woven hose 13 x 3 mm for vacuum, temperature range: -40 .. + 120°C. 

PVC-hose 9 x 2 mm, temperature range: -20 .. + 60°C. 

Silicone hose 5 x 1,5 mm, temperature range: -60 .. + 180°C. 

Viton-hose 5 x 1,5 mm, temperature range: -20 .. + 300°C. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


32

ACCESSORIES FOR FLOWMETER AND ISOKINETIC CONTROL UNIT 

product 

Rotameter 

for the indication of the flow rate during the sampling. Complete with quick release hose connector, material: PVC, measuring accuracy: 2 % 

of the final value. Calibrated at Air 20°C, 1013 mbar. 

Range: 0,02 - 0,36 m³/h, 

Range: 0,6 - 6 m³/h, 

Rotameter to 4.1 m³ / h, very robust housing glass cone - flowmeter (0-100%, 4.1 m³ / h) 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


33

WASHING BOTTLES, CARRYING BOX , CONNECTING FLANGE 

FOR GAS SAMPLING WITH BUBBLER MUST USE A HEATED SUCTION TUBE WITH DIRECT CONNEC- 

TION TO THE BUBBLER. 

Bubbler with frit D0 

Bubbler with frit D0 for gas analysing, Set with three bubblers, one with check valve (shuts of when the sampling is 

terminated so that the liquid does not flow back into the suction pipe through the reduced pressure) and two standard 

bubblers, each with frit D 0, volume: 250 ml, Material: Duran. 

Entrance = Pan KS 19 

Exit = Ball KS 19 (last bubbler with smooth tube 10 mm) 

Have a look on our test report about the difference between Impinger and Frit-bubbler at different flow rat 

Bubbler (250 ml) filled with 100 ml water. 

Injection tube smooth Injection tube impinger Injection tube with frit D0 

Test flow rate: 1 m³/h 

All show a good mixing. The frit has no bad mixing events. 

More pressure drop over the frit about 30 hPa 

Test flow rate: 0,3 m³/h 

The best mixing has the frit followed by the impinger. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


34

MATCHING CLAMPS FOR KS 19 

Matching clamps for KS 19 

CARRYING BOX FOR THE WASHING BOTTLE 

Material: PVC, with an aluminum plate at the front for linking it to the filter device heater (for a direct link to a suction pipe the flange of the 

large heating is necassary). 

Carrying box for 3-bubbler in series 1 bubbler street, 

Length: ~490 mm, Wide: ~100 mm, High: ~170 mm, 

Carrying box for 6-bubbler in series, for 2 bubbler streets, 


Carrying box for 9-bubbler in series, for 3 bubbler streets, 


Connecting flange 

CONNECTING FLANGE 

for mounting the carrying box at the suction tube. With this flange can fixed the big heater and / or the carrying box at the 

suction tube. Material: Aluminium. Flange for heated and cooled suction tube. 

This flange is in the dilvery capacity of the big heater and must order only if the carrying box for bubbler is mounting directly at 

the suction tube. 

Strain relief for bubblers 

STRAIN RELIEF FOR BUBBLERS 

Clip for mounting at carrying box for bubbler. Include hose tube and thread with fast coupling system, each for hose clear width 9 

mm. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


35

FLOW MEASUREMENT 

PITOT TUBES 

L- (Prandtl) Pitot Tube 

suitable for measurements in aggressive gases and can be used without any correction-factor (VDI 2640, part 3 and ISO 

16911). Available Material: Titanium, Stainless Steel and special Steel for the use in 1000°C hot gases. 

S-Pitot Tube 

S-PITOT TUBE 

suitable for measurements in aggressive gases and can be used with correction-factor (ISO 10780: 1994 (E) and ISO 

16911, delivery with calibration certificate). Can deliver with integrated thermocouple NiCr-Ni. 

Available Material: Titanium, Stainless Steel and special Steel for the use in 1000°C hot gases. 

Cylindrical Pitot Tube (according to VDEh) 

CYLINDRICAL PITOT TUBE 

is suitable for measurements in tube-systems with small openings. With calibration certificate for the correction factor. 

Available Material: 

Stainless Steel and special Steel for the use in 1000°C hot gases. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


36

ACCESSORIES FOR THE EMISSION SAMPLING LINES 

VACUUM HOSE 

Vacuum hose 13 or 19 mm, temperature: -40 ... +120° C 

HOSE CLAMP STAINLESS STREEL 

hose clamp for 13 or 19 mm hose, Stainless Streel 

QUICK RELEASE HOSE CONNECTOR 

Quick release hose connector (small), internal thread G½, for hose male: 34.05, material: chromized brass 

HOSE CONNECTOR 

Hose connector for G½-hose (I.-Ø. 13 mm ), for female connector: 34.04, material: chromized brass 

QUICK RELEASE HOSE CONNECTOR 6K-3/4 

Quick release hose connector (big), 6k-3/4 internal thread G¾, for hose material: chromized brass 

HOSE CONNECTOR 

Hose connector G½- or G ¾- hose for female connector material: chromized brass 

SEAL FOR BIG COUPLING 

Seal for big coupling 6K-3/4 material Viton up to 300°C 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


37

DOUBLE-COUPLING 

Double-Coupling for big male plug 

MALE PLUG WITH THREAD G ¾ 

Male Plug with thread G ¾ 6k-3/4 

CLOSING CAP FOR BIG COUPLING 

Closing Cap for big coupling 

PLAN FILTER HOLDER 

Plan filter holder with circle-ring-grooves for the plane filter device, Material: Stainless Steel or Titanium, 

Size: Plane filter Ø 45 mm, Plane filter Ø 47 mm, or Plane filter Ø 50 mm, 

PLANE FILTER, MATERIAL: QUARTZ FIBRE 

Plane filter, material: quartz fibre, precipitation 99,99 % with DOP, unit with 25 pieces, special for havy metal analyse, 

Size: Ø 45 mm, 47 mm or 50 mm 

PLANE FILTER FROM GLASS FIBRE (100 PCS) 

Plane filter, material: glass fibre, precipitation 99,99 % with DOP, unit with 100 pieces, high purity 

Size: Ø 45 mm, 47 mm or 50 mm 

PETRI GLASSES FOR PLANE FILTER HOLDER 

Petri glasses for plane filter holder with lower part and cover from glass (Ø 80 mm) for plane filter holder Ø 45-50 mm 

TINPLATE BOX FOR PLANE FILTER HOLDER 

Tinplate box for plane filter holder Ø 45-50 mm Ø 70 x22 mm, weight 29,3 g. Easy opening and tight closing through mechanical 

push-switch system 

Transport Suitcase for Plan filter holder Ø 45 - 50 mm 

TRANSPORT SUITCASE 

made of plastic with handle for save and contamination free transport. The filter holders are transported lying and can 

take out easy without any loss of filter material, matching for 8 petri-glasses Ø 80 mm (without petri-glasses). 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


38

FILTER HUSK 

Filter husk the bush should be stuffed with wool or with thimbles. Generally employ a cone when using glass- or quartz-thimbles. 

The cone guarantees that the gas flow moves into the thimble and not past it. 

The Titanium husk is for glass- and quartz fibre thimbles from comp. Munktell. the bush should be stuffed with wool or with 

thimbles. Generally employ a cone when using glass- or quartz-thimbles. The cone guarantees that the gas flow moves into the 

thimble and not past it. 

The Titanium husk is for glass- and quartz fibre thimbles from comp. Munktell. 

TITANIUM CONE 

Titanium cone for filter husk It is not necessarry to conditioning the cone with the single glass- or quartz fibre thimble (2-3 cones 

are sufficient for all samplings) 

FILTER THIMBLES TYPE GOTHE (25 PCS) 

Glass fibre thimbles type Gothe 603 GM (MG 160), from comp. Munktell, retention: 0,3µm: 99,998 %, size: outer- Ø: 26 mm, 

internal-Ø: 21,5 mm, length: 68 mm, weight ca. 3g, pressure drop ca. 200 mbar, unit with 25 pieces 

Quartz fibre thimbles type Gothe, type G-Ti (MK 360) from comp. Munktell, Tmax.: 900° C, < 0,3 µm: 99,998 %, size: outer- Ø: 

26 mm, internal-Ø: 21,5 mm, length: 68 mm, weight ca. 3g, pressure drop ca. 200 mbar, unit with 25 piecesv 

TRANSPORT GLASSES 

for filter husk, glass with thread and cover 

SUITCASE 

Suitcase for safe and free of contaminations for 8 transport glasses (without transport glasses) 

CARTRIDGE FOR PLUG WITH GLASS FIBRE FOR HIGH DUST FILTER DEVICE 

Size of the cartridge: internal Ø: 56 mm, length: 150 mm, out of high-grade steel with high-grade steel filter base 

weight ca. 365gv 

DUST COLLECTOR FOR CYCLONE 

Dust collector for cyclone 75 cm³ with cover (Ø 50 mm x L: 45 mm) 

QUARTZ WOOL 

Quartz wool 500 g, Fibre size 5 to 30 µm. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


39

GLASS WOOL 1000 G, SUPERFINE 

Glass wool 1000 g, superfine 

GAS WASH BOTTLES PFA. PTFE 

PFA. Cap with S 40 buttress threads and frit made of PTFE. A pore size of approx. 50 μm for optimal pearling of the gas into the 

liquid. A wide field of application is possible due to the use of high-quality fluoroplastic. Suitable only for non-pressurised operation. 

Capacity 250 / 500 / 1000mL 

BOTTLES FOR GAS WASH BOTTLES 

Bottles for Gas Wash Bottles Boro 3.3. NS 29 / 32. Size 100 / 250 / 500 ml without stand. 

GAS WASH BOTTLE ADAPTERS 

Gas Wash Bottle Adapters Made of DURAN® tubing. Without / With sintered glass disc and safety head, NS 29 / 32. 

RETTBERG GAS WASH BOTTLE 

Rettberg Gas Wash Bottle form with filter disc porosity 1, capacity 500 ml, two-piece version, with greasefree connection flange size 

DN 50, incl. Viton-O-ring and three-point clamp (aluminium), connections with thread and plastic hose connectors (PP), complete. 

High gas flow rate and saturation thanks to larger cross section of the filter disk and longer rise. 

GAS WASHING BOTTLE PP 

Gas Washing Bottle PP. Graduated cylinder with Vikem vinyl stopper. Insert and 70 μm frit made of PE. 

GLAS GAS WASH BOTTLES 100ML/250ML, 

Glas Gas wash bottles 100mL/250mL, different models 

GASKETS WITH PTFE WALL FOR GL SCREWCAP 

Gaskets with PTFE wall for GL screwcap 

HOSE CONNECTORS IN PTFE 

Hose connectors in PTFE 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


40

LOW-COST ACRYLFLOWMETERS 

Low-cost acrylflowmeters, various ranges/sizes (e.g. 0.04-0.5NL/min), accuracy 5% 

DIFFERENT FLOWMETERS 

Different flowmeters, sizes 65mm or 150mm, accuracy ±2%FS , with/without needle valve, measuring ranges from 6mL/min max. 

flow 

ROTAMETER 

Rotameter for the indication of the flow rate during the sampling. Complete with quick release hose connector, material: PVC, 

measuring accuracy: 2 % of the final value. Calibrated at Air 20°C, 1013 mbar. 

Range: 0,02 - 0,36 m³/h, 

Range: 0,6 - 6 m³/h, 

ROTAMETER UP TO 4,1 M³/H 

Rotameter very robust housing (0-100 %, 4,1 m³/h) With the following configuration: 97 Connection: Thread / vertically, A device 

version: Standard limit signal: without fitting material: stainless steel 1.4571 Application: Gas assembly type / thermowell: Geräteanschlussart 

line installation / polycarbonate: pipe thread, appliance connector: 1/2 "/ 1 / 2 ", stop material inlet / outlet: stainless 

steel 1.4571 1 stainless steel 1.4310, measuring tube Schwebek. combination: FP1 / 2" -27 11 GNSVT-48 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


41

SEAL, GASKET 

Aramid-composite-material (max. 400°C), Aramid-composite-material graphitize (max. 400°C), Teflon (max. 220°C), Silicone (max. 200°C), 

soft Nyhalit (max. 300°C) 

Information to the sealingmaterial: 

Aramid-composite material: Aramid (known as Kevlar) is a high temperature-stable aromatic Polyamid-fibre. These fibre don't melt, it is resistant 

against acids and organic solvents. Through admix of softeners (e.g. Rubber) the fibre stuck together and can use as seals. This mixture 

loses their softeners from 150°C and becomes fragile. The function as seal is still given until 400°C. After this thermal treatment, the seal 

can use not a second time, they are too brittle. By the treatment with graphite, the evaporation of the softeners is clearly delayed and the seal 

consequently reach a longer temperature-stability. 

Nyhalit: Material of Nyhalit becomes fragile at application until 300°C and can not use a second time. 

Teflon: Teflon is thermal stable until 250°C, becomes very soft from 200°C however and can not use as a safe seal. 

Size 

Ø mm 

Used Area 

Size 

Ø mm 

Used Area 

Di 1 24/38 Probe part: 1/40 Di 32 16/43 zero pressure probe with wrap mother Ø 50 

mm 

Di 2 32/48 probe part: 1/50 Di 33 43/72 bent with plane filter holder Ø 45 mm 

Di 3 44/58 probe part: 1/60 Di 34 11/15 quartz tube 

Di 4 24/50 zero pressure probe with wrap mother Ø 55 mm Di 35 18/38 filter device part: 302 

Di 5 24/50 zero pressure probe GT with wrap mother Ø 55 

mm 

Di 6 32/50 zero pressure probe with wrap mother 

Ø 55 mm 

Di 7 32/50 zero pressure probe GT with wrap mother Ø 55 

mm 

Di 36 34/59 bent with plane filter Ø 37 mm 

( drawing 8455 ) 





Di 8 12/19 for all threads with internal thread G ½ Di 39 98/124 drying tower part: 16-A 

(middle) 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


42

Size 

Ø mm 

Used Area 

Size 

Ø mm 

Used Area 

Di 9 18/24 all external threads G ¾ Di 40 72/110 high dust filter 

part 12 

Di 10 32/38 filter husk (9.0) Di 41 72/110 high dust filter 

part 12 

Di 11 30/38 filter husk (8.0) 

and threads G 1 

Di 42 72/110 high dust filter 

part: 12 

Di 12 43/49 plane filter Ø 45 mm (11.02-top) Di 43 55/67 glass drying tower 

Di 13 40/47 plan filter Ø 45 mm (11.02-top) Di 44 98/111 glass drying tower HLUG 

Di 14 46/55 plane filter Ø 50 mm (11.03-top) Di 45 52/58 XAD- part: 619/620 

Impactor 60.01 

Di 15 48/56 plane filter Ø 50 mm (11.03-bottom) Di 46 45/56 XAD- part: 619/620 

gas probe 4.32 

Di 16 100/110 plane filter Ø 110 mm (12.03-top) Di 47 67/88 drying tower Teil: 16-B 

(small) 

Di 17 100/116 plane filter Ø 110 mm (12.03-bottom) Di 48 24/42 filter device part: 302 

Di 18 44/66 plane filter Ø 45 mm, P-45 

in bent 

Di 49 22/43 gas probe 6960 

for 50 mm 

Di 19 44/66 plane filter Ø 45 mm, P-45 in bent Di 50 43/30 gas probe: 6957 

Di 20 34/58 plane filter Ø 37 mm, P-37, in bent Di 51 32/39 plane filter Ø 37 mm P-37 

Di 21 34/58 plane filter Ø 37 mm, P-37, in bent Di 52 35/43 plane filter Ø 37 mm P-37 

Di 22 20/24 probe 1/25 Di 53 6/28 extensible pitot tube Ø 15 mm 

Di 23 18/24 cyclone-part 11 and 15 Di 54 8/32 extensible pitot tube Ø 20 mm 

Di 24 24/37,4 cyclone part 11 and 15 Di 55 13/18 hose connector G ½ ( 80°C ) 

Di 25 26/38 filter device (7.0) with thread G ¾ Di 56 11/24 hose connector G ¾ ( 80°C ) 

Di 26 14/20 cyclone 

part 11 and 15 

Di 57 24/34 combi-probe 

Di 27 20/26 all threads external G ½ Di 58 55/80 filter chamber 30.6 

Di 28 48/72 plane filter Ø 50 mm part P-50 in bent Di 59 15/7 

15/3,5 

for pitot tube in combi probe 

Di 29 48/72 plane filter Ø 50 mm part: P-50 in bent Di 60 58/72 high dust filter 13.03 

Di 30 40/45 plane filter Ø 45 mm part 350 Di 61 61/72 high dust filter 13.03 

Di 31 45/50 plane filter Ø 50 mm part 352, Di 62 49/54 Impactor 60.01 

Di 63 40/55 plane filter device glass P-37 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


43

PACKING CORD 

Paxking cord to seal the holder and the inner tube from the suction tube 

SPACER WITH SEAL 

Spacer (Stainless Steel) with seal (rubber) for inner tube for cooled suction tube. 

INNER TUBE/LINER FOR SUCTION TUBES 

Inner tube, 10 x 1 mm, material:Titanium for suction tubes with exchangeable inner tubes 

CLOSING CAP FOR 

Closing cap for G ½, G ¾, Caps with seals to close the threads, material: brass, with PTFE-Seal 

SEALING PLUG FOR ½ FEMALE THREAD 

Sealing plug for ½ female thread to close outer threads G ¾ (leak test). 

ADAPTER FOR FILTERHEAD 

Adapter for filterhead Connecting part for plane-filter-device VDI 2066, Bl. 7 and Impactor behind external thread G ½, e.g. behind 

the bent or suction tube. Entrance: Screw cap G ½, exit: External thread G ¾ with conical exit, material: Titanium (up to 

400° C), weight: ~ 0,2 kg 

ADAPTER FOR THREADS 

Adapter for threads internal thread G ¾ - external thread G ½ 

CONNECTION PART KS 19 

Connection part KS 19 to connect bubblers behind external thread G ½. Entrance: internal thread G ½, exit: ball KS 19, material: 

titanium, weight: ~ 0,1 kg 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


44

CONNECTING PART WITH INTEGRATED THERMOCOUPLE 

Connecting Part with integrated Thermocouple This part can be used for the regulation of the heater in the suction tube 

and the heater for the filter device. It measured directly in the gas stream. The gas temperature can directly be read and 

thus a falling below the dew point can be avoided. Available in Stainless Steel and Titanium, with NiCr-Ni, with 3 m cable. 

Entrance: Screw cap G ½ Exit: External thread G ½ 

SUBSTITUTE PART 

Substitute part This part has the length of the filter devices and can set for it. Entrance: internal thread G ½, exit: external 

thread G ½ 

ADAPTER FOR SUCTION TUBES WITH EXCHANGEABLE INNER TUBE 

Front adapter for suction tubes with exchangeable inner tubes. 

Adapter to fixed the bent at suction tubes without integrated internal tube, 

entrance: screw cap G ½, exit: external thread G ½ with hole for tube 10 x 1 mm. 

FRONT ADAPTER FOR SUCTION TUBES WITH FIXED INNER TUBES. 

Front adapter for suction tubes with fixed inner tubes. 

Adapter to fixed the bent at suction tubes with integrated internal tube 10 x 1 mm, 

entrance: screw cap G ½, exit: external thread G ½. 

STUFFING GLAND 

Stuffing gland to seal the inner tube from a suction tube 

GAS DISTRIBUTOR: 

Gas distributor: To separate the main gas stream into two gas streams. e.g. one main gas volume for the hose with the big pump 

and one sample stream through washing bottles. 

Entrance: Screw cap G ½ for the exit of the filter device, 

90° bent exit with external thread G ¾ with the hose fast connector. 

Exit: 2 x M 12 thread for adapter. 

KS-19 BALL FOR GAS DISTRIBUTOR 

KS-19 ball for gas distributor 

Entrance M 12 thread for gas distributor 40.19-T, with matching seal (Di-8-M, the same seal as for G ½ thread), 

Exit: ball KS 19, 

Material: Titanium. 

HOSE NOZZLE FOR GAS DISTRIBUTOR 


Entrance: M 12 thread for gas distributor 40.19-T, with matching seal (Di-8-M, the same seal as for G ½ thread), 

Exit: Hose nozzle (6 .. 10 mm hose), 

Material: Titanium. 

CLOSING CAP FOR GAS DISTRIBUTOR 

Closing cap for gas distributor 

Entrance M 12 thread for gas distributor 40.19-T, with matching seal (Di-8-M, the same seal as for G ½ thread), 

Exit: ball KS 19, Material: Titanium. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


45

TEMPERATURMESSGERÄT MINI-K (-64 BIS +1370 °C). 

Temperature measuring device Mini-K (-64 .. +1370 °C) The compact and waterproof measuring device is ideally suitable for operating 

various K-typ sensors.Usage areas are heating/air-conditioning or process measurements. Delivery without the sensors. 

Included in the delivery: Battery (CR2032). Manual: only German Version. Splash-water protected IP65, Features: Hold display, 

Automatic switch-off, C/F-changeover. 

Technical data 

Dimensions: (W x H x D) 43 x 78 x 20 mm 

Specification: Mini-K (niCr-Ni) 

Base accuracy: ±(1% or 1 °C) 

Power supply: 1 x CR2032 

Resolution, temperature: 0.1 °C 

Temperature range: -64 to +1370 °C 

Weight: 41 g 

TEMPERATURE CONTROLLER 

Temperature controller for all filter heater, all electrical heated suction tube with integrated thermocouple NiCr-Ni and both short and long 

heated sampling lines 

Housing from Makrolon, for thermocouple NiCr-Ni, with permanent digital 3-digit reading of the actual temperature. The scanning rate of the 

signal processing is 120 ms with a resolution of 10.000 points. There is one output for heater with exchangeable relay for resistive load (5 A 

fuse, 230 V) with status-LED. Control structure: ON/OFF, P, PI, PID - heating; self-optimization, adaptive optimization and alarm functions. 

Switchable to manual heating (impulse heating without thermocouple). 

Voltage: 210-240 VAC, Resistive load: 5 A, 

JACKET THERMOELEMENT, NICR-NI (TYPE K), 

Jacket thermoelement, NiCr-Ni (Type K), Class 1, -220 °C...+1150 °C, different lengths, diameters and connections possible 

TRANSMITTER FOR THERMOCOUPLE 

An analogue transducer for thermocouples acc. DIN EN 60584 or DIN 43713. The temperature-sensitive voltage will be transformed 

voltage-linearly into a output signal. The transducer can mounted inside the protection head type B. 

HEATED SAMPLING LINE 

Heated sampling line with internal PTFE hose 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Robust internal carrier hose 

Hose end caps in silicone rubber 

Isolated with filt and 7mm silicone foam 

Outer protection in polyamide braiding 

Power consumption approx.. 100W/m 

length at demand 

Traction relief with stainless steel pulling cable 

Options: 

Exchangeable or fixed internal hose 

Second non-heated PTFE hose e.g. for calibration 

Integrated power or signal cable 

Diameter internal PTFE hose 6mm, 8mm or greater 

Two internal heated hoses instead of one 

Inox end pieces to prevent damage to internal hose 

Explosion proof version (ATEX) 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


46

PTFE TUBE / TEFLON HOSE 

PTFE tube / Teflon Hose Inside Ø of 0.5 mm, and 10 mm 

SWAGELOK COUPLINGS 

Swagelok couplings 

TRIPOD TO SUPPORT PROBES 

Tripod to support probes Tripod for probes Adjustable height 

MAINTENANCE KIT FOR SUCTION PUMP 

Maintenance Kit / Maintenance Kit for suction pump Ritschel TLV 6. TLV 15 consisting of: 6 x lamella, 1 x gasket set (3 seals) and 1 x Microtop 

cartridge 

RITTER HIGH ACCURACY WET (DRUM-TYPE) GASMETER 

Ritter high accuracy wet (drum-type) gasmeter, range from 0,016 L/min to 300 L/min, measuring accuracy ±0.2% 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


47

ABS-N/ABJ-NM, WITH HIGH-QUALITY SINGLE-CELL WEIGHING SYSTEM AND EC TYPE APPROVAL [M] 

ABS-N/ABJ-NM The bestseller in analytical balances, with high-quality single-cell weighing system and EC type approval [M] 

Only ABJ-N: Automatic internal adjustment in the case of a change in temperature > 2 °C and time-controlled every 4 hours 

Only ABS-N: Adjusting program CAL, external test weights at an additional price 

Dosage aid: High-stability mode and other filter settings can be selected 

Simple recipeweighing and documenting with a combined tare/print function. In addition, the mixing ingredients for the recipe are 

numbered automatically and printed out with their corresponding number and weight value 

Identification number: 4 numeric positions, printed on calibration protocol 

Automatic data output to the PC/printer each time the balance reaches a steady state 

Single-cell advanced technology: 

Fully automatic manufactured weighing cell from one piece of material 

Stable temperature behaviour 

Short stabilisation time: Steady weight values within approx. 3 sec under laboratory conditions 

Shock proof construction 

High corner load performance 

VACUUM DESICCATOR MOBILEX 'READY TO USE' 

Vacuum Desiccator MOBILEX 'ready to use' 

Vacuum desiccator with screw thread in the lid. With desiccator base with flat flange, no outlet, desiccator lid with threaded 

outlet type MOBILEX, porcelain desiccator plate, silicone sealing ring with bonded PTFE face, stopcock 

with PTFE spindle, PBT screw cap with pierced aperture GL 32. 

AUTO-DESICCATOR WALL, PMMA 

Bohlender Auto-Desiccator Wall, PMMA Temperature resistance: - 20 to + 70 °C 

6 chambers, 6 doors, each chamber usable with up to 17 shelves, incl. 1 shelve, 1 tray and 1 hygrometer per chamber. Electrical 

power connection 230 V / 50 Hz is required. 

6 Big-Star-desiccators in compact design. Solid casters with brakes. Ground clearance for comfortable handling. Further shelves 

optionally available. Separate doors with extra strong magnetic lock. 

MEMMERT VACUUM OVENS VO SERIES 

Vacuum ovens VO allow handling of heat- and oxygen-sensitive substances and materials gently. Adjustable temperatures 

from 20 to 200 °C, pressure range from 10 to 1100 mbar. Short heating times, precise temperature control and turbo-drying. 

Basic model: 

Working chamber stainless steel, 1.4404 (ASTM 316), housing textured stainless steel (rear zinc-plated steel). 

Underglass function display, push-turn control. 

Weekly programme timer with real-time clock, ramp timer. 

MEMoryCard XL for programming up to 40 temperature and pressure ramps and documentation of temperature and pressure-(vacuum) process. 

USB-interface. Electrical supply: 230 V, 50 / 60 Hz. 

Works calibration certificate for 160 °C at 50 mbar pressure for each thermoshelf shipped together with the vacuum oven. 

Items supplied: 

Removable interior mounting. 

Thermoshelves made of aluminium 3.3547 (ASTM B209), coated with eloxal, with integrated large-area heating (size 200: 1 thermoshelf, 

sizes 400 and 500: 2 thermoshelves). 

Modules (optional): 

Inert gas inlet: programmable and digital controlled inlet for inert gas with flow rate reduction. 

Pump control: optimised rinsing procedures for the pump membranes as well as signal output for pump ON / OFF (recommended in combination 

with PMP). 

Premium module: comprises the inert gas inlet, pump control, one printer interface, extra connectors for thermoshelves 1 (size 200) resp. 2 

(size 400 / 500), an additional thermoshelf (size 400 / 500) and a drip tray. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


48

MANOMETER / BAROMETER 

DIGITAL MANOMETER GREISINGER GDH 200-13 

Digital manometer for over/under pressure or pressure difference 

Measuring range: 0.0...199.9 or 0...1999 mbar rel. ( ± 1999 mbar) 

Resolution: automatic change 0.1mbar / 1mbar 

Miscellaneous: automatic zero point adjustment, manual slope adjustment, tare function, auto-off 

DIGITAL BAROMETER GREISINGER GPB 3300 

GPB 3300 Digital barometer 

Resolution 0.1 mbar 

Sea level-adjustment 

Manual slope and offset adjustment 

Measuring range: 300,0 ... 1100,0 mbar (hPa) abs. 

Overload: max. 4000 mbar abs. 

Accuracy: ± 2.0 mbar (at 0-50°C) 

Selectable measuring units: mbar, mmHg 

Features: Sea level correction, Min-/max- value memory, Auto-Off, BAT, 

Zero-function, digital offset and scale adjustment 

Shipment: 1 device incl. sensor, 1 Battery, 1 operating manual 

WAT- 

PROOF PRESSURE HANDHELD DEVICE WITH 2 SENSOR CONNECTION, ANALOG OUTPUT AND 

DATA LOGGER GMH 5155 

GMH 5155 Waterproof pressure handheld device with 2 sensor connection, analog output and data logger 

Features: 

Water-proof (device and plug-in connections), Serial intervace, Analog output, Data logger, Average filter, Silicone protection 

cover, Large double display, Background illumination 

Application: 

Industry und craft, HVAC: heating, ventilation, air-conditioning, Leakage test / pressure test, Chimney draft measurement: under 

pressure, Leakage test at buildings (i.E.: 4 Pascal test), Measurements of gas and oil firings, Automobile trade 

Sensor connections: 2 

Sensor: 1x 7-pole bayonet socket 

Output / ext. Supply 4-pole socket for serial interface and supply (with accessories: USB adapter USB 5100) 

Display: two 4½-digit 7-segment display (15 mm and 12 mm) 

Data logger: 0 - 1 V, freely adjustable with measuring point input, 40 adjustable measuring point texts or measuring point numbersValue memory: 

Cyclic: 8.000 data sets / Singular: 1000 data sets 

Min-/Max-Alarm: channel: 3 - off: Alarm function inactive - on: Alarm report via display, integrated buzzer and interface 

- no Sound: Alarm report only via display and interface 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


49

TESTO 435-4 - MULTI-FUNCTION MEASURING 

With the multi-function measuring instrument testo 435-4 perform all measurements, you need to adjust ventilation and air-conditioning systems 

and to assess the ambient air quality. A differential pressure sensor for Pitot tube measurement and filter monitoring is integrated in the 

testo 435-4. In addition, you have a comprehensive range of optional sensors and probes to choose from. 

This meter uses a sensor to start. 

Product advantages: Including differential pressure sensor for Pitot tube measurement or filter monitoring. Further optional sensors (z. B. 

Anemometer, humidity probes, Lux and degree of turbulence probe) available for differents-th measurement purposes. Large Instrument memory 

for up to 10,000 readings. PC software for Ana lysis and documentation of measurement data including 

TESTO 417 - VANE ANEMOMETER 

Vane Anemometer testo 417 enables measurements at the air outlet and inlet, 

The clear display not only displays current speed and direction, but also Vo-volume flow and temperature. In addition to the time 

and point averaging, you can read the min / max values by pressing a button. 

Advantages: Compact anemometer with integrated 100 mm vane, measurement of flow, volume flow and temperature Ideal for 

measurements at the air outlet and air intake, measurement of poppet valves, ventilation grilles and swirl diffusers possible with 

optional accessories 

THE AIRFLOW INSTRUMENTS VELOCITY METER TA440-A 

The Airflow Instruments Velocity Meter TA440-A is like having multiple meters for the price of one, yet simple to operate. The TA440-A 

includes an articulated probe– all in one compact package. Ideal applications include HVAC system performance, commissioning, plant maintenance, 

critical environment certification and duct traverses. 

FEATURES AND BENEFITS 

Articulated probe 

Accurate air velocity measurement 

Simultaneously measures and displays velocity, temperature and humidity 

Calculates volumetric flow, wet bulb and dew point temperature 

Data logging 

INCLUDED ITEMS 

Instrument with articulated probe 

Hard carrying case 

Four alkaline batteries 

USB cable and LogDat2 Downloading Software 

Operation and service manual 

Calibration certificate 

HÖNTSCH VERY ROBUST ROTARY VANE ANEMOMETER 

Höntsch very robust rotary vane anemometer, range 0.01 ... 120 m/s at temperatures of -40 ... +550 °C for liquid or gaseous 

media 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


50

GAS ANALYZERS 

TESTO 350 

The testo 350 Portable Emission Analyzer 

Analyzer box - for high accuracy measurements 

Contains up to six sensors, pumps, gas path, sample conditioning, and more 

Utilizes continuous sensor temperature monitoring for superior accuracy 

Conditions the gas sample automatically, thermoelectric (peltier) chiller as required by regulatory agencies 

TESTO 340 4-GAS COMBUSTION ANALYZER 

The ultimate instrument in portable combustion and engine tuning 

Optimizing combustion, increasing efficiency and minimizing fuel use are necessary to compete in today's market. The Testo 

340 provides the information to understand your process, enabling you to make informed combustion decisions. It is the ideal 

tool toconfirm proper set-up or identify emission problems. 

Up to 4-gas sensors to use and measure simultaneously 

CO sensor with dilution (option) for high-range testing 

Infrared printing so you can print records (flash Mode) to Testo infrared printer 

Mass measurements in lbs/year 

Rugged and durable – 4-Gas Flexibility in a rugged, compact handheld design 

4-gas choice of O2, CO, COlow, NO, NOlow, NO2, and SO2 

Field-replaceable pre-calibrated sensors means zero downtime 

so you can keep testing! 

All sensors read at the same time 

18 fuels to choose from, plus 10 user-defined fuels (input from easyEmissions) 

Automatic Sensor Protections keeps your analyzer working longer 

Integrated pressure sensor measures draft or differential pressure and simultaneously measure exhaust gas and flow velocity for flow 

Designed for simple, fast operation and constructed for demanding daily rugged use 

JNOX NO2 TO NO CONVERTER 

The JCT JNOX series of NOx converters are designed to efficiently convert NO2 to NO prior to measurement 

by NDIR extractive analysers. The high quality and reliability of the conversion is characterized by an efficiency 

of over 95% at high flow rates, as well as a low maintenance, long life converter cartridge. 

The JNOX series converters are available in 4 different models including options for bypass streams with selection 

valves and metallic or carbon converter material; thus ensuring that the JNOX series meets all requirements. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


51

GAS CONDITIONING AND SAMPLING 

JCM GAS COOLER 

The JCM series gas cooler from JCT is based on the peltier technique of cooling. This proven technology allows for an 

extremely robust compact cooler that is also very lightweight, hence it is ideal for use in applications with limited space. 

The JCM series coolers are available with a range of options that can include moisture monitoring, integrated peristaltic 

drain pumps and/or temperature alarm. These compact gas coolers have corrosive resistance high quality heat exchangers 

and are ideal for gas analysis or water analysis. 

JC 14 AND JC 24 PELTIER COOLER 

The new peltier coolers JC 14 and JC 24 provide a reliable gas conditioning prior to gas analysis. They have a 

short start-up time and are applicable for continous operation. The JC 14 and the JC 24 are upgradeable to turnkey 

gas conditioning units. Optionally available with: condensate detector, solenoid valve, calibration port, sample 

gas pump, stainless steel gas inlet. 

M&C GAS COOLERS, CONDENSATE REMOVAL AND SEPARATORS 

The ECP 1000 gas cooler is used in gas analysis to lower the dew point of humid to avoid condensation in the analyser. 

An extremly stable gas dew point avoids water vapour crosssensitivity and volumetric errors. one stream, max. flow 150 

Nl/hr, different materials of heat exchangers, power 115/230V 60/50Hz 

M&C GAS CONDITIONINGS PORTABLE, FOR MAX. 350NL/HR 

The M&C portable gas conditioning unit PSS-5... is designed to carry out precise gas analyses at different locations.The 

entire gas conditioning unit is housed in a robust aluminium-frame case to enable the user to carry out a 

rapid gas analysis, which is safe with little maintenance work. The PSS-5... gas conditioning unit is suitable for 

variable, discontinuous use as well as for continuous operation. The components built into the PSS-5... gas conditioning 

unit can be used for standard applications. If you have special problems please ask us for other solutions. 

M&C OXYGEN ANALYSERS PMA 10 230V 

Due to the extremely fast response time of the patented M&C magneto-dynamic measuring cell with no stagnant 

volume as well as the negligible cross sensitivity from other sample gas components, the portable M&C oxygen analyser 

PMA 10 has a wide variety of applications. The analyser is a suitable and reliable instrument for monitoring 

oxygen concentrations in various gas analytical control applications including flue gas-, inert gas-, fermentation processes-, 

food packing machines-, ambient air- and laboratory process control measurements. 

TAILOR MADE CASE FOR ANALYSER 

Tailor made case for analyser and/or accessories 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


52

WORKPLACE ATMOSPHERES MEASUREMENTS PERSONAL AIR 

SAMPLING PUMP AND STATIONARY PUMPS FOR SAMPLING FOR 

RISK MATERIAL MEASUREMENT 

GILAIR PLUS PERSONAL AIR SAMPLING PUMP (1 - 5,000 CC/MIN) 

One Air Sampling Pump with All the Features You Need and Want 

QuadModeSM Air Sampling Technology 

Selectable Automatic Fault Recovery 

Standard Temperature & Pressure Correction 

Superior Design & Comfort 

Real-time Clock with Data-logging 

Innovation Delivered 

The ultimate personal air sampling pump delivering enhanced performance, greater versatility, and superior design and comfort. 

The Widest Flow Range of Any Personal Air Sampling Pump 

The GilAir® Plus features wide dynamic flow and pressure ranges to address all personal air sampling methods with flow ranges between 20 

and 5,000 cc/min. With patent pending QuadModeSM air sampling technology, the GilAir Plus can perform both high-flow constant pressure 

and constant flow (450-5,000 cc/min) and low-flow constant pressure and constant flow (20-499 cc/min) with a single pump without external 

adaptors. It's like getting two pumps in one. 

Unmatched Versatility 

Samples particulates, vapors, gases, and metal fumes 

Works with all common sampling media 

Multi-language capability: English, Spanish, French, Italian, Dutch, Portuguese and German 

Outlet port for bag sampling 

GILIAN 5000 PERSONAL AIR SAMPLING PUMP (20 - 5,000 CC/MIN) 

The Gilian 5000 is a high-performing personal air sampling pump leading the industry in back-pressure performance, reliability 

and ease-of-use. The pump offer flow rates up to 5000 cc/min, and thanks to several advanced features, the pump 

overcome the main causes of sampling errors, saving you time and money. The air flow display holds calibration for 30 

days, even with atmospheric changes. The back-pressure capabilities of the Gilian 5000 are the highest in the industry for 

any personal sampling pump. 

Up to 5 LPM 

Highest back-pressure capability 

Programmable 

Live flow display 

NiMH battery 

EN1232 - Type P compliant 

GILIAN 800I AIR SAMPLING PUMP (200 - 800 CC/MIN) 

Gilian 800i is a powerful personal air sampling pump targeting applications requiring a 200 to 800 cc/min flow range and 

backpressures up to 80 inches H2O. Gilian 800i is an ideal solution for VOC monitoring applications using thermal 

desorption tubes, including modified versions of NIOSH method 2549 and EPA TO-17 at higher flow rates for improved 

sensitivities. 

Gilian 800i is powered by a memory-free NiMH battery pack that provides run-times over eight hours and quick-charge 

in less than four hours. The pump is controlled by a lockable keypad linked to a digital menu interface. Gilian 800i can 

be programmed for scheduled sampling or intermittent duty cycles, delayed start, or a four stage program with repeat 

cycling. 

With intrinsically safe certification for use in hazardous classified areas and meeting EN 1232 Type-G for personalized 

sampling pump performance in workplace environments, Gilian 800i is the new leader for powerful low flow personal air sampling. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


53

GILIAN GILAIR-3 AND GILAIR-5 AIR SAMPLING PUMPS (0 - 3,000 / 0 - 5,000 CC/MIN) 

The GilAir pumps (GilAir-3 & GilAir-5) have one of the largest user bases of any air sampling pump worldwide. These 

reliable 3 and 5 liter per minute air sampling pumps have automatic constant flow assuring sampling is maintained 

within +/- 5% of the initial set point. Setting the flow rate on the GilAir-3 & GilAir-5 is a simple process that requires 

no special adjustment tool so you spend less time configuring pumps. 

The most recognized air sampling pump on the market. 

The GilAir-3 and GilAir-5 are recognized for durability and reliability when it counts most. 

Automatic constant flow — the most important feature of any sampling pump — is standard on all GilAir-3 and GilAir-5 pumps. It assures flow 

is maintained within 5% of the initial set point, even with varying back-pressures from flow restrictions or buildup of material on the filter. 

GilAir-3 and GilAir-5 pumps are suitable not only for conventional pull-through sampling media but also for bag sampling and other pressure 

applications. 

NiMH batteries are now available for the GilAir-3 & GilAir-5. 

The GilAir-3 and GilAir-5 are now available with nickel-metal hydride (NiMH) batteries that virtually eliminate memory effects and lazy battery 

issues. NiMH batteries are environmentally friendly, recyclable and do not pose a risk to the environment when being disposed. New NiMH 

battery packs are backwards compatible with GilAir-3 and GilAir-5 pumps that currently use NiCd batteries and are user replaceable by removing 

only two screws on the rear of the pump. 

GilAir-3 and GilAir-5 pumps also boast these features: 

Basic, Clock, & Programmable Models The GilAir-3 and 5 are available in 3 models; Basic, Clock and Programmable. The Basic model is 

straight-forward and easy to use. Clock models provide an elapsed-time clock display. Programmable models enable a timer which can start 

or stop the pump at preset time intervals or program a delayed start. 

Flow Fault & Test Indicators 

The fault light indicator activates when the pump flow control is outside +/-5% of the required flow rate, such as from low battery, blocked 

tubing or filter. If fault conditions persist for 30-60 seconds, the pump automatically shuts down and freezes the timer. Models with a timer 

display preserve run time on the display, ensuring a valid sampling result. When the fault condition is cleared before shutdown, the pump will 

resume normal sampling and fault light turns off. The GilAir-3 & 5 also has a Battery Test indicator light that illuminates when the battery can 

provide a minimum of 8 hours of operation over operating range. 

External Filter Housing 

Clear filter housing allows an immediate visual inspection of the internal filter's condition. This feature protects the pump from dirt and debris 

and is externally mounted on the pump, allowing for quick inspection. Filter replacement requires the removal of just four screws. A built-in 

moisture trap helps prevent moisture from entering and damaging the pump chamber, such as moisture carryover from impingers. 

Optional Low Flow Modules 

Constant Flow module allows sampling from 20-500 cc/min. 

Constant Pressure (Multi-flow) Module allows sampling from 1-750 cc/min. 

These modules can be quickly added to pumps to adapt them to the lower flow rates required for sorbent tube sampling. The multi-flow module 

maintains constant pressure and allows sampling with multiple sorbent tubes, each with an independently set flow rate. 

GilAir-3 & GilAir-5 Hazardous Approval Ratings: 

UL: Class I, Division I, Groups A, B, C & D Class II, Groups E, F & G Class III, Temp Code T3C 

CE: Ex II 2 G, Eex 1a IIC T4 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


54

GILIAN GILIBRATOR-2 NIOSH PRIMARY STANDARD AIR FLOW CALIBRATOR 

The Gilibrator-2 System provides users with a convenient and highly automated way to check almost any commercially available air sampling 

pump for proper air flow function before deployment. The system consists of an electronic Gilibrator-2 Base which is used with any of three 

sizes of wet bubble cells. These patented interchangeable components are also available as part of kits which can also include a complete 

calibration diagnostic panel. All cells use a twist-on bayonet design for quick and easy mounting to the base. All are certified for accuracy and 

traceable to NIST. 

Calibration Cells 

Three bubble cells are available, for air flow ranges of 1 to 250 cc/min (low flow cell), 20 cc/min to 6 LPM (standard flow cell) and 2 to 30 LPM 

(high flow cell). These interchangeable wet cells generate perfect bubble films at the touch of a button. An infrared sensor reads the bubble 

flow rate, which is then calculated and displayed. 

Gilibrator-2 Base 

Easy to operate, microprocessor-controlled unit features simple on/off and reset touchpad with large LCD screen that displays flow rate, the 

calculated average of multiple flow samples in a series and the sample number. Light in weight, it operates with either AC power or rechargeable 

batteries (8???hour life) for easy portability in either the lab or the field. 

Gilibrator-2 Diagnostic Kit 

Offers the industrial hygienist a complete, portable calibration laboratory. Consists of Gilibrator-2 Base with three wet bubble cells in a 

cushioned carrying case, with a full diagnostic panel built into the top lid of the case. The panel uses an interchangeable rotameter design for 

2 to 5,000 cc/min flow capability and will run any of several diagnostic tests:"Load" simulation ?__ Offers two load simulations for high and 

low flows to imitate sample line back-pressures.Back-pressure reading ?__ A built-in Magnehelic?? gauge allows visual monitoring of in-line 

back-pressures up to 40" H2O (10 kPa).Leak checking ? Built-in Magnehelic?? gauge allows visual leak testing and monitoring capabilities.Pump 

flow adjustment ?__ Rotameters allow instant visual indication of approximate flow rates, assisting in properly adjusting air flows. 

Optional PC Interface Kit & Printer 

A PC Interface Kit is available for real-time data download and manipulation. The kit includes a cable for connecting a computer to the RS-232 

port of the Gilibrator-2 Base, as well as software that allows the user to log pump and calibrator serial numbers, data, operator name, flow 

rates, averaging data, number of samples, sample sequence, and standard deviation data. An optional printer is available for hard copy printouts 

of ?? calibration data. 

ACCESSORIES FOR WORKPLACE ATMOSPHERES MEASUREMENTS 

All accessories for workplace atmosphere measurements: nozzle sets, filter holders, cyclone filter holders for respirable dust, etc. 

KC ADSORPTIONTUBES 

SKC adsorptiontubes 226-01 (active carbon), 226-10 (silicagel), 226-30 (XAD-2), 226-57 (XAD-7), etc. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


55

DRÄGER GAS DETECTOR PUMP ACCURO® 

The Dräger Tube® measurement system is a proven method of measuring contaminants in soil, water or air. More than 

500 substances of different concentrations can be measured. 

All Dräger Tubes® are alike in configuration and operation, a certain volume of air has to be drawn through the tube. This is 

done using the accuro® gas detector pump. When brought into contact with a particular substance, the chemical reagent 

system inside the tube reacts and changes colour. The concentration of the substance is indicated by the length of the 

discolouration and can be read off directly from a scale. 

The Dräger Tube® measurement system offers the benefits of measurement accuracy, cost efficiency and quick and easy operation. More 

than 250 tubes for a huge variety of substances, applications and measurement ranges are available upon request. 

accuro® set: pump incl. case, tube opener and spare part set. 

RENTAL EQUIPMENT / USED EQUIPMENT 

Rental of gas analyzers and accessories 

The following devices are available upon request with timely deadlines vote with us available for rent: 

Mietgeräteliste 

Subject, rental period, price and other terms are agreed in advance of a rent in a lease. Rental equipment can be either sent to be picked up 

by us or delivered by us. Filled gas cylinders are excluded from shipping. The shipment of rental equipment is done by us overnight delivery 

usually to 12 clock the tenant or another agreed address. The rent is determined according to the rental period after daily or weekly rates. 

Transportation times and costs are to be considered. 

In case of early redelivery only the actual rental period is calculated. In case of delayed return of the tenant bears the additional costs. For 

rental periods from four weeks Discounts are possible. 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


56

FID 3-200 (J.U.M.® ENGINEERING) 

FID 3-200 heated, portable FID for total organic carbon measurements, TÜV qualification tested 

Heated FID Model 3-200 is a portable, versatile, robust total hydrocarbon analyzer for high accuracy, sensitivity 

and stability. The Model 3-200 is based on our tried and tested for over 30 years flame ionization detector {FID), 

which is integrated together with the sample gas-carrying components in a heated chamber at 190'C for the loss 

of Koh-lenwasserstoffmolekülen avoid having hohern molecular weight and to enable reliable measurement 

results-Nisse for trace measurements in ultra-pure gases and air and other gases. The per-manent heated 

sample gas filter is permanently installed and is cleaned by backwashing with compressed air and has a replaceable 

Filtersiebscheibe with a pore size of 2 PRM. Connected Measuring gas lines are automatically carried 

out when each Rückspülvorgan g. The generator for the tsrennluft is installed. A costly, external supply of combustion 

air from gas cylinders is there-her superfluous 

FID 3-100 (J.U.M.® ENGINEERING) 

FID 3-100 (J.U.M.® Engineering) heated, portable FID for total organic carbon measurements 

This particularly compact designed FID Model 3-100 was developed specifically for the mobile one-sentence. 

The analyzer is insensitive to vibrations and can also be used in the vehicle. He is a reliable, easy-to-use instrument 

with a high-security Betriebssi for measuring the total hydrocarbon concentration in air and in other 

gases. Base is a specially developed for continuous measurement flame (Fl D). For Ver-avoidance of the loss 

of hydrocarbons with high molecular weight are FID and all housed with sample gas components coming into 

contact in a heated chamber to 200'C 

FID 3-300A (J.U.M.® ENGINEERING) 

FID 3-300A (J.U.M.® Engineering) 

The 3-300A heated FID was designed in the early 80's as a space saving alternative to our VE7. Also the 3- 

300A was a "first" in the industry due to its sample filter back purge feature. It is also a very much liked 19" 

rack mount heated FID throughout the stack testing community and well known for its ruggedness, forgivingness 

and long standing accuracy and sensitivity. The 3-300A is fully identical to the VE7 and 3-200 and 

has been officially approved for that. 

TÜV approved and certified for 2. BImSchV. 13. BImSchV and 17. BImSchV and fully complies with QAL1, EN 

12619, EN 13526 (EU) and with EPA Method 25A and Method 503 (USA) 

Features 

Maintenance free sample filter back purge system allows filter to be cleaned without dismantling (automatic optional) 

Built in burner air generator, no external air cylinder needed 

All components in contact with sample fully heated and controlled at 190 degree C 

Built-in sample pressure and sample pumps 

Automatic flame out alarm and contact 

Fast response within 1 second 

Low fuel consumption 

Very selective 

Microprocessor controlled PID-type temperature controller 

Remote control for sample, calibrate and back purge is standard 

Remote or automatic range change optional 

Applications 

Stack gas hydrocarbon emissions monitoring 

Fence line monitoring 

Raw exhaust vehicle emissions analysis 

Catalytic converter testing 

Measuring engine combustion efficiency 

Hydrocarbon contamination monitoring in air and other gases 

Carbon adsorption regeneration control 

Detection of trace hydrocarbons in purity gases used in the semi conductor industry 

LEL monitor of solvent laden air 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


57

FID 109A (J.U.M.® ENGINEERING) 

The J.U.M 109A is being build since 1989. It is a heated FID analyzer to continuously and simultaneously 

measure the Methane concentration, the Total Hydrocarbon concentration and the Non Methane concentration 

simultaneously within a gaseous sample. The 109A is a table top or 19-inch rack mount Heated FID analyzer 

for the NMHC measurement in ambient air, exhaust gases from a combustion process e.g. stack emissions, 

from any type of an industrial vent, from an internal combustion engine, or from any other emission containing 

hydrocarbons. 

The 109A can be used as a table top or rack mount analyzer. It fully complies with EN 12619, EN 13526, QAL 

1 (EU), with 2. BImSchV, 13. BImSchV and 17. BImSchV, (Germany) and with EPA Method 25A and Method 503 (USA). 

Features 

Made in Germany 

All critical components including pumps, sample filters, detectors and main electronics are manufactured in house 

Dual detector/ dual electrometer design 

Fully heated to 190 degree C 

Equipped with zero and span gas inlets to be selected from internal selector or from remote sources. Auto cal check optional 

Typical sensitivity 0.01 ppm CH4 

21/2 digit LED display. Optional direct concentration display to read up to 3 decade ranges without range change 

Internal sample pump and air pump 

Internal combustion air supply (No external air cylinder needed) 

Very low fuel consumption (less than 20 cc/min @ 100% H2) 

Disposable sample filter in rear panel 

Automatic ignite capability (optional) 

Automatic flame out alarm contact and fuel shut off 

Sample pressure regulator not in contact with sample gas 

Multiple range capability, 5 selectable ranges are standard 

19" rack mount unit, 221 mm high 

Applications 

Optimization of natural gas fired baking ovens and other furnaces 

Gas purifying system monitoring 

Stack gases (CEM) and all other Environmental and process applications 

Air and gas scrubber efficiency 

Process chemical gas analysis 

Personnel safety 

Solvent recovery 

Catalytic converter and thermal combustor testing 

Automotive catalyst and engine emissions 

Fence line (perimeter) monitoring 

NON METHANE HYDROCARBON CUTTER MODELL 900 (J.U.M.® ENGINEERING) 

Modell 900 is an external Non Methane Hydrocarbon Cutter which allows the added capability to measure 

alternately METHANE ONLY or THC with one heated total hydrocarbon analyzer (HFID). 

The J.U.M. Engineering Model 900 External NMHC Cutter is the low cost alternative compared to "all in one" 

heated non methane hydrocarbon analyzers. The cutter is housed in a 19 inch rack mount case and is to be 

added in series to the sample inlet of a total hydrocarbon FID analyzer. In the "Methane"-mode the catalyst 

allows only Methane to reach the FID analyzer. The FID analyzer will consequently measure Methane only. 

In the "THC"-mode the catalyst is bypassed and the FID analyzer will consequently measure total hydrocarbons, 

including the Methane. A stainless steel assembly (pat. pend.) which contains a proprietary catalyst is 

housed inside of the heated oven in the rack mount case. The heated oven is maintained at a stable temperature by an internal microprocessor 

controlled temperature controller. 

The Model 900 includes all necessary plumbing, our permanent sample filter which is cleaned by back purging and all solenoid switching 

valves, all in one oven. The switching valves allow the catalytic converter to be switched into and out of the sample stream. The heated FID 

analyzer will consequently measure total hydrocarbons or methane only. To determine the non-methane hydrocarbon concentration the methane 

concentration needs to be subtracted from the total hydrocarbon concentration following the various national regulations. All connectors 

are on the rear panel, all controls are activated by front panel switches. Remote control for CH4-sample, THC-sample, calibrate and backpurge 

is available. 

Technical Data 

Dimensions W x D x H (mm): 483 (19") x 580 x 132 

Converter chamber: fully heated 

Chamber temperature: factory pre-set, locked and wire sealed 

Temperature control: dgital PID-type controller with µ-processor 

Catalyst effiency: >98% for Ethane and heavier hydrocarbons. 

warm up time: 180 minGas connectors: stainless steel 616S, Swagelok® 1/4" 

Max. sample flow: 2,5 Liters / Minute 

CnHm inlet. concentration: max. 1000 ppm Propane equivalent 

Power requirements: either230VAC/50Hz, 500 W or 115VAC/60Hz, 500 W 

Ambient temperature: 5°C - 43°C (41°F - 110°F) 

Weight: approx. 17 kg 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


58

PRANDTL PITOT TUBE WITH ELECTRIC PRESSURE SENSOR (AIRFLOW) 

Prandtl Pitot Tube WITH ELECTRIC Pressure sensor (AIRFLOW) 

HEATED SAMPLING LINE (WINKLER) 

Heated sampling line (Winkler) with Temperature controller 

SAMPLE GAS DILUTION MODELL 108 (J.U.M.® ENGINEERING) 

The Model 108 dilutes an introduced sample gas in a 1:10 (standard), or a 1:100 (optional) dilution rate to allow 

the linear measurement of hydrocarbon concentrations above several thousand ppm up to 10% and above. The 

sample injection method is used in this 190 deg.C heated sample diluter for fast response and improved zero 

and span stability of a hydrocarbon measurements. 

The Model 108 is also used to minimize negative effects due to highly concentrated interference compounds and contamination. Additionally, 

so called "memory effects" or hydrocarbon hang-up due to condensation of heavy hydrocarbons as well as other condensed impurities in the 

sample gas can be largely prevented. A total hydrocarbon analyzer, placed downstream of the diluter will continuously draw a constant 

amount of zero or room air through the diluter. The internal sample pump draws the sample into the diluter. The Model 108 is equipped with a 

permanent sample filter to be back purged with high pressure air or nitrogen for cleaning, 2 micron stainless steel sample filter. Downstream 

of the internal sample pump is the actual dilution capillary setup which is controlled by precision flow/pressure regulation to ensure a constant 

flow of sample through the diluter capillary. The diluter capillary flow is finely adjustable to maintain the correct injection amount. 

Features 

All components in contact with sample fully heated and accurately controlled at 190 deg.C 

Built-In air pressure pump and heated sample pump 

1:10 dilution rate is standard 

1.100 dilution rate is available instead of 1:10 as an option 

Standard, permanent installed sample filter to be cleaned by back purge with hydrocarbon free compressed air or with nitrogen. 

Optional available is an easy to change sample filter in stead of the back purge filter. It is accessible on the rear panel. No special tools required 

for filter changes 

Calibration valves for zero- and span calibration, standard manual turn switch and remote operation, e.g. PLC or PC 

Large oven temperature display with analog 0-5 VDC temperature output @ 10mV/deg.C 

Precision sample pressure regulator on front panel for precise and easy calibration 

Fast response 

Applications 

Stack gas hydrocarbon emissions monitoring 

European-EPA and USA-EPA Method compliance monitoring of high concentration raw source hydrocarbons before a catalytic or thermal 

combustion 

Catalytic converter testing 

Flare gas HRVOC emissions monitoring 

THC/NMHC testing of fuel cell reformer emissions 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


59

OXYGEN ANALYSERS PMA 10 (M&C TECHGROUP) 

Due to the extremely fast response time of the patented M&C magneto-dynamic measuring cell with no stagnant 

volume as well as the negligible cross sensitivity from other sample gas components, the portable M&C 

oxygen analyser PMA 10 has a wide variety of applications. The analyser is a suitable and reliable instrument 

for monitoring oxygen concentrations in various gas analytical control applications including flue gas-, inert 

gas-, fermentation processes-, food packing machines-, ambient air- and laboratory process control measurements 

PORTABLE OR FOR WALL MOUNTING, COMPACT, FOR MAX. 70NL/HR 

The M&C portable gas conditioning unit CSS-M is designed to carry out precise gas analyses at different locations.The 

entire gas conditioning unit is housed in a robust aluminium-frame case to enable the user to carry 

out a rapid gas analysis, which is safe with little maintenance work. The CSS-M gas conditioning unit is suitable 

for variable, discontinuous use as well as for continuous operation. The components built into the CSS-M gas 

conditioning unit can be used for standard applications. 

Portable gas conditioning system type CSS-M for 70Nl/h. In a steel-sheet housing, consisting of: Peltier gas 

cooler ECP regulated to 5°C, fine filter FPF-2 with liquid alarm, sample gas pump N3KPE, peristaltic pump 

SR25.2 and flowmeter FM40. Power: 230V/50Hz. # The sample gas pump starts automatically when gas cooler 

remains under +8°C. 

Datenlogger COMBILOG LT 1021 (Theodor Friedrichs) 

DATENLOGGER COMBILOG LT 1021 (THEODOR FRIEDRICHS) 

versatile data logger for multiple analog and digital inputs and outputs, alarm and arithmetic channels, extensive 

sensor database, cyclical automatic data transfer to PC or Note-book possible, suitable with GSM modem for remote 

data transmission. 

‣ 6 analog inputs (voltage, current, resistance) 1 analog output 0 ... 10 V 

‣ 16 digital inputs / outputs (status, counter, frequency, Gray code) 

‣ Alarm and arithmetic functions - 512 kB internal memory 

‣ extensive sensor database - A / D conversion: 10 bit 

‣ sampling and recording intervals selectable (in increments) 

‣ serial interfaces RS 232 and RS 485 - Power supply: 10 ... 30 VDC 

‣ Housing: Aluminum / ABS - Dimensions: 189 x 90 x 83 mm (WxHxD), IP 20 

‣ Weight: 720 g 

‣ Installation: DIN-rail mounting (35 mm) 

Accessories: 

‣ COMGRAPH software for data acquisition from COMBILOG LT 1021 incl. Evaluation (Table-steering and graphics options), data 

exportable and readable in Excel 

Combilog Configuration Software 

‣ to create projects in the datalogger (channel allocation, data storage intervals, averaging times etc. Programming; Programming of 

the data logger is done via RS 232 interface) 

DATENLOGGER LASCAR EL-USB-3 

Datenlogger LASCAR EL-USB-3 

Single-channel data logger with 0-30 V input and USB interface to upload to PC 

‣ 1 analog input 0 ... 30 V DC - internal resolution 50 mV 

‣ inaccuracy about 1% (resolution 2.5 decimal places) 

‣ Memory capacity: 32510 Data 

‣ USB interface for configuration and data readout 

‣ recording intervals selectable from 1 second to 12 hours (in increments) 

‣ 2 programmable alarm thresholds 

‣ Status indication with 2 LED 

‣ Supply: 3.6V lithium-ion battery 

‣ plastic housing 

‣ Dimensions 110 x 23 mm (L x D) 

Accessories (Software) 

‣ EasyLog USB 

‣ easy to understand software for configuring and reading the data (English) 

‣ equires Windows XP or Vista 

‣ Data visualized as a graphic, as a graphic printable and exportable (eg in Excel) 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


60

NOTEBOOK 

Notebook 

USB ports, software for reading single-channel data loggers (type EL-USB-3) and the data acquisition of Combilog 

data loggers. 

Notebook S10-2 black 

Processor: Intel Atom N270 

Display: 10.1-inch WXGA (1024 x 600) LED TFT glossy 

HD 160 GB, 1024 MB DDR2 

Fi, RJ45, Mic, Speakers, Headphones, VGA, 3xUSB 2.0, software: Windows XP, Ecograph (for reading COMBILOG data loggers), 

EasyLog USB (for reading LASCAR data loggers), OpenOffice 

SERVICE / REPAIR OF FID ANALYZERS JUM® ENGINEERING 

For the sake of high measurement reliability and the long-term value preservation of a FID analyzer we recommend, depending on the operating 

conditions a maintenance devices in one- to two-year intervals, more frequently in exceptional cases. 

A standard FID maintenance in our workshop takes about a week and includes the following work: 

‣ decomposition, thorough cleaning and installation of all measured gas leading parts (measuring gas filters, measuring gas valve, 

sample gas and control air pump, tubes, capillaries) 

‣ renewal of wear parts in pumps and filters (pump diaphragms, valve plates and seals, measuring gas exchange filter cartridge, dust 

filter) 

‣ Setting the pump pressure, lubricate the pump bearings 

‣ cleaning of the detector 

‣ control and if necessary renew the spark plug 

‣ refilling the air filter cartridge 

‣ checking all electrical equipment functions (heating, display, ignition amplifier, valve functions, measurement outputs) 

‣ control and possibly optimizing the flame settings of the detector (reduction of sour-material cross-sensitivity) 

‣ calibration and testing 

CALIBRATION 

DKD (ISO17025) Calibration of gas meters, Ritter drum gas meter, Pitot tubes and manometer etcetera…………. 

(On request pick-up and delivery service) 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


61

SAND TEST INSTRUMENT, ELEMENTAL ANALYZERS AND 

SURFACE MEASURING INSTRUMENT 

AREAMAT SPECIFIC SURFACE AREA DETERMINATION OF SOLIDS 

With the AREAMAT you can determine quickly, easily and accurately the specific surface of finely divided, dispersed 

solids or porous materials using the Brunauer, Emmet and Teller method (BET, see DIN 66131). 

Typical customers are manufacturers of adsorbents, catalysts, fillers, fertilizers, cement, metal powders, pigments, 

pharmaceutical and ceramic materials and other solids. 

BET single point methode according DIN 66131, low temperatures-nitrogen adsorbtion, Extensive measuring 

range 

Equilibrium method, no influence of transport processes and thermal diffusion, the adsorbate coverage of all accessible pores 

Differential method, no influence of the dead volume, no vacuum required 

Fully automatic, fast response times, automatic endpoint detection and analysis, the output of the differential pressure during the measurement 

Wide-mouth glass jars, suitable for larger material (neck diameter 18 mm) 

Automatic switching between water and cold bath, automatic level control 

Automatic storage of the curve to the conclusion, visual comparison of the measured curves by graphical overlap 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


62

AREAMETER SPECIFIC SURFACE AREA DETERMINATION OF SOLID 

With the Areameter you can determine quickly, easily and accurately the specific surface of finely divided, dispersed solids or porous materials 

using the Brunauer, Emmet and Teller method (BET, see DIN 66131). 

BET single point methode according DIN 66131, low temperatures-nitrogen adsorbtion, Extensive measuring range 

Equilibrium method, no influence of transport processes and thermal diffusion, the adsorbate coverage of all accessible 

pores 

Differential method, no influence of the dead volume, no vacuum required 

Manual operation system, fast response times, manuel endpoint detection and analysis, the output of the differential pressure 

during the measurement 

Wide-mouth glass jars, suitable for larger material (neck diameter 18 mm) 

Manual switching between water and cold bath, manual level control, only manuel valve control possible 

THERMOSTAT FOR SAMPLE PREPARATION AREAMAT / AREAMETER 

Thermostat for Areamat / Areameter for external sample preparation to parallel degassing of up to 8 samples 

Temperature adjustable up to 300 ° C 

ACCESSORIES FOR BET ANALYSIS 

product 

Adsorption vessel KPG 9 / KPG 18 with or without sealing plugs 

displace capillary KPG9 / KPG 18 

adapter for adsorption vessel 

cover for Dewar vessel 

flow meter rota meter – thermostat 

set of seals and O-rings 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


63

ACCESSORIES FOR BET ANALYSIS 

product 

hose connection 

regulator for nitrogen 

plug for adsorption vessel KPG 18 to purge the thermostat with nitrogen 

plug for drying tube 

drying tube 

overpressure vessel and O-ring Buna 17x2 

plug for adsorption vessel KPG 18 

plug to close adsorption vessel KPG 18 

vessel holder KPG 18 

holder KPG 18 for displace capillary 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


64

Benefits and Specifications 

Innovation in Moulding Material Testing 

SAND TEST INSTRUMENT 

Our new sand test instrument helps you to work more accurately, to create less rejects on raw material and thus keep 

your costs at a minimum. At the same time, it is easy to handle and robust in construction. 

One Instrument for All Tests 

The comprehensive options for measurement together with a high reproducibility of your measurements and the analysis 

of mechanical-technological parameters reduces your work to a fraction of its orginial amount. Due to its all comprising 

functionalities, it replaces an entire sand test lab which makes it on top of that also a space saver. 

‣ robust 

‣ space-saving 

‣ automatical testing 

‣ adjustable / variable testing speed 

‣ high reproducability 

‣ time saving 

‣ simple / uncomplicated handling 

‣ user friendly 

‣ security system provided 

‣ precise calculation of analysis results 

‣ fast change-over at testing 

GAS PERMEABILITY DEVICE GJ1 

The gas permeability device GJ1 measure the gas permeability of foundry sand. The gas permeability is influenced by 

the clay content, the degree of compaction and the sand grain size. 

STRENGTH TEST INSTRUMENT 

The strength test device SJ1 measure the compression / bending / shear is / double shear and the splitting tensile 

strength of green and core sand. 

PNEUMATIC COMPACTOR CJ1 

The Compactor CJ1 is approved only for the compression of green sand. With the device, the compressibility can be linked to 

form a clay substance determined in%. By the pneumatic device, the different compaction is excluded by different users. The 

sample will be compressed pneumatically reproducible with a pressure of 100 N/cm² 

‣ quick and uniform testing the compactibility 

‣ digital result 

‣ ergonomic work 

‣ robust construction and easy operation 

‣ optional interface for data transfer 

‣ large display 

PNEUMATIC EJECTOR 

he pneumatic ejector EJECTOR is exclusively for ejecting from compacted Green and core sand by VDG (German Association 

Foundry Professionals) produced specimens. The specimens are ejected by moving down the Pneumatic cylinder without changing 

their properties. Also Core sand samples with no split specimen tube can be ejected gently. 

Advantages 

‣ no alteration of the test specimen properties 

‣ improved reproducibility of shear, pressure and gap measurement 

‣ the sand specimen will not be damaged during ejection 

‣ minimizing the additional compaction 

‣ ergonomic working 

‣ no defective sample 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


65

AGITATOR 

The mechanical, analogue mixers provide a very high torque at low speeds and a falling at high speeds. Thus, both high viscosity 

fluids are slowly stirred, and thin liquids are thoroughly mixed. The electronically controlled, digital mixers have, however, 

a constant torque throughout the speed range. They are used to create reproducible test conditions. 

Technical data 

‣ Rotation speed under nominal load 0/150 – 6000 rpm 

‣ Rotation speed attitude stepless 

‣ Rotation speed – Setting accuracy 1 rpm 

‣ Nominal voltage 230 +/- 10% VAC 

‣ Frequency 50/60 Hz 

‣ max. power output at the agitator shaft 125 W 

‣ dimensions (LxWxH) 316 x 200 x 1000 mm 

‣ weight approx. 5,3 kg 

CS1001 

CS1001 

Features of the Carbon/Sulfur Analyzer 

Analysis principles: 

Infrared light absorption during combustion in Oxygen flow. 

HF Induction furnace 

Options: 

Selectable temperature ramps 

Selectable different frequencies 

Selectable different power for combustion 

Solid state infrared detectors with gold path for simultaneous detection of SO2 and CO2 gas 

Automatic furnace dust cleaning by brush 

Automatic furnace cleaning by Oxygen 

Robot module 

Automatic high/low range selection 

Options: 

Up to 4 different detectors 

Selectable range for each IR detector 

THE HYDROGEN ANALYZER SPECIAL FOR ALUMINIUM AND ALUMINIUM ALLO 

Features of the Hydrogen Analyzer special for aluminium and aluminium alloy 

Analysis principles: 

Melting of the sample in a high frequency induction furnace (HF). 

Features 

Melting point control with automatic furnace stop 

Automatic furnace cleaning by N2 gas 

Gas calibration 

Measurement of temperature by pyrometer 

Self cleaning of the quartz combustion tube by heating 

SPARE PARTS AND CONSUMABLES 

We have the following for systems manufacturers constantly consumables, spare parts and consumables 

Ströhlein Instruments 

JUNG INSTRUMENTS 

others on request 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


66

ELECTRIC STEAM GENERATOR STAINLESS STEEL 

The innovative electrically heated steam generator in the market of high-quality stainless steel 1.4301 in absolute premium quality. All wetted 

parts are stainless steel quality 1.4571. The systems are adapted to the individual needs of our customers 

‣ for heating 

‣ moistening 

‣ deforming 

‣ drying 

‣ sterilization 

‣ pasteurization 

‣ homogenizing 

‣ cooking, simmering, tires, shoes 

‣ as a heat source for other production processes 

‣ independence from major central supplies 

‣ steam generation where it is needed 

‣ no space-consuming boiler house 

‣ no recurring boiler testing necessary by rapid amortization of the steam generator 

‣ no oil tank required 

‣ no energy loss in long pipes 

‣ clean and easy handling 

‣ individual, to the needs of their 

‣ company tailored steam generators 

‣ approval in accordance with European Pressure Equipment Directive 

‣ Built-up only wetted parts made of stainless steel 1.4571 

‣ use of demineralized water to produce the saturated steam possible 

Steam amount of 14 kg/h Until 448 kg/h Higher power on request 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


67

FUME CUPBOARDS / PATHOLOGY 

FUME CUPBOARDS STAINLESS STEEL 

Fume cupboards made of stainless steel 

are produced on the individual needs of our customers. 

PATHOLOGY 

Pathology cutting tables stainless steel 

are produced on the individual needs of our customers. 

LABORATORY SUPPLIES / LABORATORY INSTRUMENTS YOU CAN FIND IN OURE 

LABORATORY CATALOGUE 

Laboratory catalogue 2015-2016 

CONSUMABLES 

INSTRUMENTS 

CHEMICALS 

LABORATORY PLANNING 

CHROMATOGRAPHY 

FOODALYT 

or under http://hm-labortechnik.eu 


Tel.: +49 (0) 02161 599 650 - Fax.: +49 (0) 02161 599 6525 


68

HM catalog Emission Control Technology 2015

Create successful ePaper yourself

Delete template?

Save as template?