Ground Fault Circuit Protection Catalog [pdf] - carlingtech.com

PC-Series ELCI/RCBO Instruction Bulletin
12 | PC-Series – Wiring Diagrams & Panel Cut Out
voltage. Can cause death or serious injury. Turn off
pply before installing PC-Series ELCI/RCBO.
t a line to line fault
of the
st MINAL instructions
ATIONS
d applications.
sures.
or hi-pot test.
fore hi-potting
ect. 550-12, NEC).
ns.
d by a qualified
to enclosure in
.
or.
wires to the Load
Fig. A for terminal
e wires directly to
e Terminals.
nd mount front
aker actuator.
structions.
l in a convenient
instruct equipment
portance of
tests.
urn on the power
flashing and the
e green “POWER”
d the red
off.
4 5 6 7 8
LOAD NEUTRAL
3. Depress the “TEST” button. This will cause the actuator to
move to the “OFF” position and the red LED to turn on and
show steady illumination, indicating that the ELCI/RCBO is
functioning properly. The green LED will also go from
steady to off. If the actuator fails to move to the “OFF”
position or INDICATE the red OFF LED / fails SINGLE to illuminate, COLOR the
HANDLE
unit MUST
/ INDICATE ON
ROCKER ACTUATOR
ROCKER ACTUATOR
be replaced.
4. Turn the ELCI/RCBO actuator to the “ON” position. The
red LED should turn off and only the green LED should be
illuminated.
5. This test is to be performed on a monthly basis and
recorded on the “Monthly Test Reminder” label.
PCE
120 WHEN VAC VERSION ELCI/RCBO TRIPS:
W/ REVERSE The PC-Series POLARITY ELCI/RCBO opens the circuit when there is an
over INDICATOR current or ground fault condition. If the red LED is
continuously illuminated the tripping is due to a ground fault
condition. If the green LED is flashing, the tripping is due to an
over current:
1. Some faults are self-clearing. Try resetting the breaker
once.
2. If this device is installed as a main breaker, turn off all
branch breakers and reset the breaker. If it does not trip,
turn branch breakers on one at a time to locate the fault.
3. If the breaker continues to trip with the branch breakers off
recheck that the neutral is not grounded on the load side
of the ELCI circuit breaker.
4. If the breaker continues to trip, but no grounding of the
PCF
120/240 VAC
neutral
VERSION
is observed, disconnect all load side connections
W/ REVERSE and POLARITY reset the breaker. If the breaker still trips with no load
INDICATOR connections in place, the breaker may be defective.
5. If the breaker does not trip with the loads disconnected but
does trip when the loads are connected, the device is
performing its intended protection function, which means
that a hazardous condition could exist. A qualified
electrician should be called to evaluate the circuit and
perform more advanced troubleshooting if the problem
cannot be located.
NOTE: NEUTRAL & GROUND PIGTAIL WIRES - SUPPLIED 12" LONG MIN. (CIRCUIT CODES A,B,E & F)
PANEL CUTOUT ROCKER
PANEL CUTOUT HANDLE
TERMINAL
LOCATIONS
DRAWING FILE NO.
CLA-8112
REV
X
REVISIONS
DESCRIPTION
X
DWG REV
01
DATE
X
3.790 [96.27]
3.040 [77.22]
2.280 [57.91]
.156 DIA. [Ø3.96]
2 PLC'S. TYP.
PER POLE
3.040 [77.22]
2.280 [57.91]
LINE 1
LINE 2
SOURCE
NEUTRAL
2.062 [52.37]
1.453 [36.91]
LINE 1
LINE 2
1.660 [42.16]
1.260 [32.00]
MATERIAL:
ASSEMBLY
FINISH:
OT 2
AD HOT 1
LINE 1
1-Phase 120 / 240 VAC
with Neutral Switching
LINE 2
SOURCE
NEUTRAL
.432 [10.97]
.750 [19.05]
LOAD HOT 2 TYP.
OR 230V NEUTRAL PCA
LOAD HOT 1
PCB, PCD & PCE
PCC & LINE PCF 1
LINE 2
OR 230V NEUTRAL
HANDLE ACTUATOR
1-Phase 240VAC
IST-0010
Rev. C
.200 [5.08]
PANEL CUTOUT DETAIL
PROPRIETARY NOTICE
NOTICE TO ALL PERSONS RECEIVING THIS
TOLERANCES DRAWING. ±.005 THIS [.12] DOCUMENT IS THE PROPERTY OF
CARLING TECHNOLOGIES, INC. AND IS NOT TO BE
DISCLOSED, REPRODUCED IN WHOLE OR IN
PART OR USED FOR MANUFACTURING PURPOSES
BY ANYONE WITHOUT THE CONSENT OF
CARLING TECHNOLOGIES, INC.
PCA, PCB
PCD & PCE
CONTROL SYMBOLS
.XXX
PCC & PCF
ROCKER ACTUATOR
DRAWING VERSION
CRITICAL DIM.
CRITICAL CHAR.
TOOL NO.
REV.
1 01.16
REFERENCE NO.
PR5055-400
INTRALINK MODEL
PR5055-400-12
INTRALINK MODEL REVISION/VERSION
X
DRAWING INTERPRETATIONS
PROJECTIONS
DIMENSIONS
INCHES
[MILLIMETERS]
UNSPECIFIED TOLERANCES
X.XXX ± .005 [0.13] FRAC. ± 1/64 [0.4]
X.XX ± .01 [0.25] ANGLES ± 1 °
MODELED BY: CHECKED BY: SCALE
TAF
DRAWN BY:
APPROVED BY:
DATE DRAWN:
04-May-10
DATE APPROVED:
DO NOT SCALE DRAWING
TITLE
C SERIES ELCI ASSEMBLY
DRAWING FILE NO.
Carling Technologies
Innovative Designs, Powerful Solutions
0.750
SIZE
D
DRAWING REV.
CLA-8112 01
PRODUCT SERIES: C SHEET 5 OF 5
4 5 6 7 8
60 Johnson Avenue • Plainville, CT 06062–1177 • Phone: (860) 793–9281 • Fax: (860) 793–9231
Email: sales@carlingtech.com • www.carlingtech.com