SmartLVL 15 Design Guide - Tilling Timber

NOTES:SINGLE SPAN VERANDAH BEAMAS 4055 CLASSIFICATION C1, C2 AND C3 [Cont’d]Roof load width (mm) 1500 3000 4500 6000 7500Rafter/truss spacing600 1200 600 1200 600 1200 600 1200 600 1200(mm)Member size Roof massDxB (mm) (kg/m 2 Maximum Verandah beam span - Single span)190x58 10 5200 5100 3700 3500 2900 2800 2500 2500 2300 170020 4800 4800 3700 3500 3000 2900 2600 2500 2300 220040 4100 4100 3400 3300 2900 2900 2600 2600 2400 220060 3700 3600 2900 2900 2600 2600 2300 2300 2200 210090 3200 3200 2600 2600 2200 2200 2000 2000 1900 1900200x58 10 5400 5400 3800 3700 3100 3000 2700 2600 2400 230020 5000 5000 3900 3700 3100 3000 2700 2600 2400 230040 4300 4300 3500 3500 3100 3100 2800 2700 2500 240060 3900 3800 3100 3100 2700 2700 2500 2500 2300 230090 3400 3400 2700 2700 2400 2400 2200 2100 2000 2000240x58 10 6400 6300 4500 4500 3700 3500 3200 3000 2800 270020 5700 5600 4600 4500 3700 3500 3200 3100 2800 280040 4900 4900 4200 4200 3700 3600 3300 3100 2900 280060 4500 4500 3700 3700 3300 3200 3000 3000 2800 280090 4000 4000 3300 3200 2800 2900 2600 2600 2400 2400300x58 10 7400 7400 5500 5400 4500 4500 3900 3700 3500 330020 6600 6600 5600 5500 4600 4500 3900 3800 3500 330040 5700 5700 4900 4900 4500 4500 4000 3900 3600 340060 5200 5300 4500 4500 4000 4000 3700 3700 3500 340090 4800 4800 4000 4000 3600 3500 3300 3200 3000 3000 5360x58 10 8300 8300 6400 6400 5200 5200 4500 4500 4000 390020 7500 7500 6500 6400 5300 5200 4600 4600 4100 400040 6500 6500 5600 5600 5100 5100 4700 4700 4200 410060 6000 6000 5100 5100 4700 4700 4300 4300 4100 410090 5500 5500 4700 4700 4200 4200 3900 3900 3600 10 3600 5400x58 10 8900 8900 7000 7000 5700 5600 4900 4900 4400 430020 8000 8000 7000 7100 5800 5700 5000 5000 4500 440040 7100 7100 6100 6000 5500 5500 5100 5100 4600 4500 560 6500 6500 5500 5500 5000 5000 4700 4700 5 4400 5 4500 1090 5900 5900 5000 5000 4600 4600 4200 5 4200 10 4000 10 4000 5450x58 10 9600 9600 7700 7700 6300 6200 5400 5400 4900 490020 8700 8700 7700 7600 6400 6300 5500 5400 4900 4900 540 7700 7600 6600 6600 6000 6000 5600 5600 5 5000 5 5000 1060 7100 7100 6000 6000 5500 5500 5100 5100 5 4900 10 4900 2090 6400 6400 5500 5500 5000 5000 4600 4700 5 4400 15 4400 25300x75 10 7700 7700 6300 6200 5100 5100 4400 4400 4000 380020 6900 6900 6100 6000 5200 5100 4500 4400 4000 390040 6100 6000 5200 5200 4800 4800 4400 4500 4100 400060 5600 5500 4800 4800 4300 4300 4000 4000 3800 370090 5100 5100 4300 4300 3900 3900 3500 3500 3300 3200400x75 10 9200 9200 8000 7900 6500 6400 5600 5500 5000 500020 8400 8300 7400 7400 6600 6500 5700 5600 5100 510040 7400 7400 6400 6400 5900 5800 5500 5500 5200 520060 6800 6900 5900 5800 5300 5300 5000 5000 4700 4800 590 6300 6200 5300 5300 4900 4900 4500 4600 4300 4300 10525x75 10 10800 10800 9900 10000 8200 8100 7100 7000 6300 620020 10000 10000 8900 8900 8300 8200 7100 7100 6400 630040 8900 8900 7800 7800 7200 7200 6700 6700 6400 5 640060 8300 8300 7200 7200 6500 6500 6100 6100 5800 5 5800 1090 7600 7600 6500 6500 6000 5900 5500 5500 10 5200 10 5300 151. D = member depth, B = member breadth, NS = not suitable.2. End bearing lengths = 35 mm at end supports and 70 mm at internal supports for continuous members. Subscript values indicate the minimum additionalbearing length where required to be greater than 35 mm at end supports and 70 mm at internal supports3. Restraint value for slenderness calculations is 1200 mm4. Not all sizes of SmartLVL 15 in this table are stocked in each state. (F17 sizes of 120, 140, 190 and 290 mm depths not currently stocked in WA).Please check with your supplier before orderingSmartLVL 15 Design Guide 59