A Study of Hole Drilling on Stainless Steel AISI 431 by EDM Using ...

More documents

Recommendations

Info

However, it is reverse proportion to water pressure and duty factor.5 AcknowledgementThis work was supported by the National Research University Project <strong>of</strong> Thailand Office<strong>of</strong> Higher Education Commission and the National Research Council <strong>of</strong> Thailand (NRCT).6 ReferencesAli S., Hinduja S., Atkinson J., Pandya M. (2009). Shaped tube electrochemical drilling <strong>of</strong> goodquality holes. CIRP Annals - Manufacturing Technology , 58, 185-188.Bilgi D.S., Jain V.K., Shekhar R., Kulkarni A. (2007). <strong>Hole</strong> quality and inter-electrode gapdynamics during pulse current electrochemical deep hole drilling. International Journal<strong>of</strong> Advanced Manufacturing Technology, 34, 79-95.Choi I-H.,Kim J-D. (1998). A study <strong>of</strong> the characteristics <strong>of</strong> the electrochemical deburring <strong>of</strong> agovernor-shaft cross hole. Journal <strong>of</strong> Material Processing Technology, 75, 198-203.Diver C., Atkinson J., Helml H.J., Li L. (2004). Micro-EDM drilling <strong>of</strong> tapered hole forindustrial applications. Journal <strong>of</strong> Material Processing Technology, 149, 296-303.Fukuzawa Y., Mohri N., Tani T. and Muttamara A. (2004). Electrical discharge machiningproperties <strong>of</strong> noble crystals. Journal <strong>of</strong> Materials Processing Technology, 149(1-3), 393-397.Guitrau E.B. (1997). The EDM Handbook. Handser Gardner publication Cincinnati, 19-54.Han F., Wachi S., Kunieda M. (2004). Improvement <strong>of</strong> machining characteristics <strong>of</strong> micro-EDM using transistor type isopulse generator and servo feed control. PrecisionEngineering, 28, 378–385.Jeong Y. H., Min B. K. (2007). Geometry prediction <strong>of</strong> EDM-drilled holes and tool electrodeshapes <strong>of</strong> micro-EDM process using simulation. International Journal <strong>of</strong> Machine Tooland Manufacture , 47, 187-1826.Muttamara A., Fukuzawa Y., Mohri N., and Tani T. (2009). Effect <strong>of</strong> electrode Materials onEDM <strong>of</strong> Alumina. Journal <strong>of</strong> Materials Processing Technology, 209, 2545-2552.Muttamara A., Janmanee P., and Fukuzawa Y.(2010). A <strong>Study</strong> <strong>of</strong> Micro–EDM on SiliconNitride Using Electrode Materials. International Transaction Journal <strong>of</strong> Engineering,Management, & Applied Sciences & Technologies, 1(1), 1-7.Rajasekhar A., Madhusudhan Reddy G., Mohandas T. (2009). V.S.R. Murti. Influence <strong>of</strong>austenitizing temperature on microstructure and mechanical properties <strong>of</strong> AISI 431martensitic stainless steel electron beam welds. Materials and Design, 30, 1612-1624.480 Pichai Janmanee, and Apiwat Muttamara
Sen M., Shan H.S.(2005). A review <strong>of</strong> electrochemical macro- to micro-hole drilling processes.International Journal <strong>of</strong> Machine Tool and Manufacture,45, 137-152.Sharma S., Jain V.K., Shekhar R. (2002). Electrochemical drilling <strong>of</strong> inconel super alloy withacidified NaCl electrolyte. International Journal <strong>of</strong> Advanced ManufacturingTechnology, 19, 492-500.Yu Z.Y., Zhang Y., Li J., Luan J., Zhao F., Guo D. (2009). High aspect ratio micro-hole drillingaided with ultrasonic vibration and planetary movement <strong>of</strong> electrode by micro-EDM.CIRP Annals - Manufacturing Technology, 58, 213-216.Pichai Janmanee is an Assistant Pr<strong>of</strong>essor in the Department <strong>of</strong> Industrial Engineering at RajamangalaUniversity <strong>of</strong> Technology Krungthep (RMUTK), Bangkok, Thailand. He received a BE in IndustrialEngineering from Rajamangala University <strong>of</strong> Technology and ME in Production Engineering from King’sMongkut University <strong>of</strong> Technology North Bangkok(KMUT’NB). His areas <strong>of</strong> research include machiningand electrical discharge machining <strong>of</strong> hard materials.9Dr.Apiwat Muttamara is an Assistant Pr<strong>of</strong>essor <strong>of</strong> Department <strong>of</strong> Industrial Engineering at ThammasatUniversity. He received his B.Eng. from Kasetsart University and the D.Eng. in Materials Science fromNagaoka University <strong>of</strong> Technology, Japan. His areas <strong>of</strong> research include machining and electrical dischargemachining <strong>of</strong> hard materials.Peer Review: This article has been internationally peer-reviewed and accepted for publicationaccording to the guidelines given at the journal’s website.*Corresponding author (A. Muttamara). Tel/Fax: +66-2-5643001 Ext.3189. E-mail addresses:mapiwat@engr.tu.ac.th. 2011. International Transaction Journal <strong>of</strong> Engineering,Management, & Applied Sciences & Technologies. Volume 2 No.4. ISSN 2228-9860.eISSN 1906-9642. Online Available at http://TuEngr.com/V02/471-481.pdf481
Page 1 and 2: 2011 International Transaction Jour
Page 3 and 4: outside diameter of</strong
Page 5 and 6: 3.1 Analysis of Wa
Page 7 and 8: Figure 5(d) shows the phenomena <st
Page 9: Figure 7 shows impressions

A Study of Hole Drilling on Stainless Steel AISI 431 by EDM Using ...

Create successful ePaper yourself

Delete template?

Save as template?