TUBE MANUAL

More documents

Recommendations

Info

Design tables for conduit systems Values are for orientation purposes only; subject to change Design of conduit systems When dimensioning a compressed air pipeline, the following items are particularly important: • A pressure decrease from 6 bar to 5 bar reduces the power of your machines and tools by up to 27%. • If the final compression pressure is increased by 1 bar to compensate for decreases in pressure, costs for operating power increase by 10%. • The following is essential for compressed air pipelines: the compressed air flow rate must remain between 5-10 m/s. • Apart from the straight pipeline sections, all pipeline fittings can be responsible for the pressure loss. Substitute pipeline lengths are specified for these pipeline fittings • Dimensioning of a closed circular pipeline takes half of the nominal length of the total closed circular pipeline and the entire compressed air requirement into consideration • At working overpressures above 7 bar, pressure loss in the pipeline is reduced • The design tables specify the respective outer diameters of the compressed air pipes because the article designations are also based on the outer diameter hndr Page 20.10.20082
Design tables for conduit systems Values are for orientation purposes only; subject to change Closed circular pipeline, aluminium Working overpressure 7 bar, ∆ P (max.) 0.2 bar, flow speed (max.) 10 m/s Alum. 25 50 75 100 150 200 250 300 400 500 750 1000 100 15 15 15 15 15 15 15 15 18 18 18 18 200 15 15 15 15 15 18 18 18 18 18 22 22 300 15 15 15 18 18 18 18 18 22 22 22 22 400 15 15 18 18 18 18 22 22 22 28 28 28 500 15 18 18 18 22 22 22 28 28 28 28 28 1000 18 18 22 22 22 22 28 28 28 28 32 32 1500 22 22 22 22 28 28 28 32 32 32 32 32 2000 22 22 28 28 28 28 32 32 32 32 40 40 3000 28 28 28 28 32 32 32 32 40 40 40 40 4000 28 28 32 32 32 32 32 40 40 40 50 50 5000 28 32 32 32 32 40 40 40 40 50 50 50 6000 32 32 32 40 40 40 40 50 50 50 50 63 8000 32 32 40 40 40 40 50 50 50 63 63 63 10000 40 40 40 40 50 50 50 63 63 63 63 63 12000 40 40 50 50 50 50 63 63 63 63 63 63 15000 40 50 50 50 63 63 63 63 63 63 63 >63 20000 50 50 63 63 63 63 63 63 63 >63 >63 >63 hndr Page 20.10.20083
Page 1 and 2:
TUBE MANUAL Status: 10/2008 Table o
Page 3 and 4:
Schneider Airsystems - Pipeline Ins
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Table of contents 1. Conventional u
Page 29 and 30:
4.1 Sliding sleeve 4.2 Blind cap 4.
Page 31 and 32:
____________________ 6 Schneider Dr
Page 33 and 34:
7. Address ____________________ 8 S
Page 35 and 36:
Page 37 and 38:
4.2 Blind cap 5. Disassembly ______
Page 39 and 40:
6. Notes ____________________ 6 Sch
Page 41 and 42:
7. Address ____________________ 8 S
Page 43 and 44:
Page 45 and 46:
5. Disassembly 6. Address _________
Page 47 and 48:
Page 49 and 50:
4.1 Sliding sleeve 4.2 Air shut-off
Page 51 and 52:
7. Notes ____________________ 6 Sch
Page 53 and 54:
8. Address ____________________ 8 S
Page 55 and 56:
Page 57 and 58:
4.2 Air outlet (clamp) 5. Disassemb
Page 59 and 60:
7. Notes ____________________ 6 Sch
Page 61 and 62: 8. Address ____________________ 8 S
Page 63 and 64: Thank you for placing your trust in
Page 65 and 66: 7. Handling and storage 8. Address
Page 67 and 68: PA pipelines, lengths of pipe and r
Page 69 and 70: PA pipelines, lengths of pipe and r
Page 71 and 72: ClickIt - brass plug-in system 15-2
Page 83 and 84: ClickIt - V4A plug-in system 15+22
Page 93 and 94: PP Screw Connection System 32-63 mm
Page 101 and 102: Brass Screw Connection System 32-63
Page 111: Design tables for conduit systems V
Page 115 and 116: Design tables for conduit systems V
Page 117 and 118: Identification of pipelines Article
Page 119: Art. no. old Art.Nr. Designation Ty
show all

TUBE MANUAL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?