Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Intended useUse and operation solely with the following machines3.2 Use and operation solely with the following machinesNOTEA suitable power source (system component) is required in order to operate the wirefeed unit!Taurus Basic 351, 401, 451, 551drive 200C drive 300C drive 4L drive 4 14099-005208-EW50110.04.2014
Intended useDocuments which also apply3.3 Documents which also apply3.3.1 WarrantyNOTEFor further information, please see the accompanying supplementary sheets "Machineand Company Data, Maintenance and Testing, Warranty"!3.3.2 Declaration of ConformityThe designated machine conforms to EC Directives and standards in terms of its designand construction:• EC Low Voltage Directive (2006/95/EC),• EC EMC Directive (2004/108/EC),This declaration shall become null and void in the event of unauthorised modifications, improperlyconducted repairs, non-observance of the deadlines for the repetition test and / or non-permittedconversion work not specifically authorised by the manufacturer.The original copy of the declaration of conformity is enclosed with the unit.3.3.3 <strong>Welding</strong> in environments with increased electrical hazardsIn compliance with IEC / DIN EN 60974, VDE 0544 the machines can be used inenvironments with an increased electrical hazard.3.3.4 Service documents (spare parts and circuit diagrams)DANGERDo not carry out any unauthorised repairs or modifications!To avoid injury and equipment damage, the unit must only be repaired or modified byspecialist, skilled persons!The warranty becomes null and void in the event of unauthorised interference.• Appoint only skilled persons for repair work (trained service personnel)!Original copies of the circuit diagrams are enclosed with the unit.Spare parts can be obtained from the relevant authorised dealer.3.3.5 Calibration/ValidationWe hereby confirm that this machine has been tested using calibrated measuring equipment, asstipulated in IEC/EN 60974, ISO/EN 17662, EN 50504, and complies with the admissible tolerances.Recommended calibration interval: 12 months099-005208-EW50110.04.201415
Page 1 and 2: Operating instructionsWire feed uni
Page 3 and 4: ContentsNotes on the use of these o
Page 5 and 6: 2 Safety instructions2.1 Notes on t
Page 7 and 8: Safety instructionsGeneral2.3 Gener
Page 9 and 10: Safety instructionsGeneralCAUTIONOb
Page 11 and 12: Safety instructionsTransport and in
Page 13: Intended useApplications3 Intended
Page 17 and 18: Machine description - quick overvie
Page 19 and 20: 4.4 Machine control - Operating ele
Page 21 and 22: Design and functionInstallationCAUT
Page 23 and 24: 5.3 Notes on the installation of we
Page 25 and 26: Design and functionConnecting the i
Page 27 and 28: Design and functionShielding gas su
Page 29 and 30: Design and functionMIG/MAG weldingF
Page 31 and 32: Design and functionMIG/MAG welding5
Page 33 and 34: Design and functionMIG/MAG weldingI
Page 35 and 36: Design and functionMIG/MAG welding5
Page 37 and 38: 6 Maintenance, care and disposalMai
Page 39 and 40: Maintenance, care and disposalDispo
Page 41 and 42: Rectifying faultsError messages (po
Page 43 and 44: Rectifying faultsWelding parameter
Page 45 and 46: Technical dataTaurus Basic drive 20
Page 47 and 48: Replaceable partsWire feed rollers1
Page 49 and 50: Appendix ASetting instructions11 Ap

Operating instructions - EWM Hightec Welding GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?