Pit Jacks, Support Systems and Accessories - Tecalemit AS

More documents

Recommendations

Info

Pit JacksMAHA Pit Jacks & AccessoriesTable of Contents:PageSelection Criteria for Pit JacksHanging Hydraulic/Pneumatic Pit JackHanging Electro-Hydraulic Pit JackTest Stand and Transmission Jack Floor-runningUniversal Jack Floor-runningJack Adaption to existing Working PitIdeal Pit Working AreaSupport Bridge ABSupport System ABTSupport System ABAYAxle TraversesPit Edge DesignSupport and Lift matrixStandard Program Hanging Pit JacksStandard Program Floor-running Pit JacksStandard Program Axle Traverse and AccessoriesStandard Program Support Systems345678910111213141516171819What ever jack you need, we have it!Manual-hydraulic – Hydraulic/Pneumatic - Electro-hydraulicA jack without a support system is incomplete!2
Pit JacksMAHA Pit Jack & AccessoriesSelection Criteria for Pit Jacks:Load capacity:0.5 / 2.0 / 4.0 / 4.5 / 6.5 / 11.0 / 14.5 / 16.5 / 20.0 / 30.0 tAllow for generous load capacity. Pay attention to loaded vehicles:When lifting a rear axle, the entire flatbed axle and the third axle are lifted.Stroke:450 / 600 / 750 / 1.050 / 1.200 mm450 mm is suffi cient for all standard jobs on trucks. If necessary, extenders can be used toreach high lifting points. 600 mm is an intermediate solution. 750 mm is required for transmissionremoval or for jobs on elevated units or trailers. For frequent work on units, a telescopic universal jackwith 1.200 mm is the right choice.Carriage:„S-Carriage“, „P-Carriage“ or „B-Carriage“The standard jack is supplied with „S-Carriage“ with a stroke of 450 und 600 mm. We supply„P-Carriages“ with a stroke of 750 mm for professional application of support bridgeswith axle traverses. Testing pits are equipped with fl oor running „B-Carriages“ jacks with750 mm stroke.Our „fl oor running“ universal jack with a „B-Carriage“ is supplied with a stroke of 1.200mm. Due to its low height it is optimally suited for transmission and unit work. This jackcan be used outside of the pit for mobile lift systems, four cylinder lifts or truck lift units.Working speed/Operation/ControlManual-hydraulic, pneumatic, hydraulic-pneumaticManual-hydraulic jacks (MGH) are offered for infrequent tasks in work pits.A jack variation with faster working speed, the MGH-Z has been developed with pneumaticcontrol. This is equipped with a compressed air high-speed control up to load point andcompressed air feedback control from load point in rest position.The hydraulic-pneumatic control (MGH-Z-LM) is optimum. This is additionally equippedwith an air motor for automatic lifting with load.Lifting platforms:Lifting platforms are needed to lift vehicles properly and securely. These are divided intoaxle traverses for vehicles which cannot be lifted in the middle, pads for different liftingpoints and in unit and transmission plates for safe removal and installation of assemblies.Support systems:Two systems are available. In one system (AB) the vehicle is lifted in the middle and supportedat two points. The other system (ABT) lifts the vehicle with an axle traverse and issupported by it.The support bridge ABAY is a mixture of both systems.The supports systems are compatible with the lifting platforms and can be used variably ina modular system.3
Page 1: Pit Jacks,Support Systems and Acces
Page 5 and 6: Pit JacksElectro-hydraulic Pit Jack
Page 7 and 8: Pit JacksHydraulic/Pneumatic Univer
Page 9 and 10: Pit JacksIdeal Pit Working PlaceOpt
Page 11 and 12: Pit JacksSupport System ABTFor lift
Page 13 and 14: Pit JacksAxle traversesThe axle tra
Page 15 and 16: Support and Jack MatrixSupport syst
Page 17 and 18: Pit JacksDelivery Program Floor-Run
Page 19 and 20: Pit JacksSupport SystemsSupport sys

Pit Jacks, Support Systems and Accessories - Tecalemit AS

Create successful ePaper yourself

Delete template?

Save as template?