ELECTRA-flo - V1.5x - 9-19-11.PMD - Air Monitor Corporation

More documents

Recommendations

Info

ELECTRA-floSECTION 5 – OPERATION5 – OPERATION5.1 – INTRODUCTIONThe ELECTRA-flo has been configured at the Factory to customer specified parameters which are recorded on theELECTRA-flo Factory Information Set-Up Sheet, provided separately. Review this information and verify that theELECTRA-flo set-up is correct for your application. If any problems or discrepancies are detected, contact Air Monitor'sCustomer Service Department at 1-800-AIRFLOW prior to proceeding.5.2 – START-UP1. After Installation has been verified in accordance with Section 4, turn power switch located at the lower front sideto the ON position (see Figure 4.1).2. Display will briefly indicate:ELECTRA-flo- - - - - - - - - - - - - - - - - - - -Thanks for ChoosingAIR MONITORFollowed by:1 8 16 24 32Sensors Found: 8Total Sensors: 8The number of active sensors will berepresented by the bar graph andlisted below. There are 8 activesensors in this example.After 5 seconds, display will indicate:1 8 16 24 32Enabled Sensors: 8Total Sensors: 8The number of enabled sensors will berepresented by the bar graph andlisted below. There are 8 activesensors in this example.After 5 seconds, display will indicate:ELECTRA-flo- - - - - - - - - - - - - - - - - - - -Sensors Warming Upwith theprogressing from left to right.after 20 seconds the display will return to Normal display mode, and the dot in the upper right of the displayindicating CPU Activated will blink rapidly (4 times per second). This is Normal operation mode and no furtheruser interface is required. If, however, user would like to verify configuration or change user selectable parameters,continue to Section 5.4 entitled "CONFIGURATION".0 ACFM *TEMP 68.0ºFVELO 0 AFPMNormal display mode*Dot flashes 4 times a second, indicatingthat CPU is active. If ALERT flashesinstead of Dot, see section forDiagnostics.Air Monitor Corporation116-053-13.P65 (2/28/12)9ELECTRA-flo - IO&M Manual
ELECTRA-floSECTION 5 – OPERATION5.3 – NORMAL OPERATIONUnder Normal operation, the ELECTRA-flo Transmitter will continuously display flow and velocity, or temperature.5.4 – CONFIGURATIONThe ELECTRA-flo onboard microprocessor controls Configuration: Operating parameter selection; input/outputactivation and scaling, and display scaling.The customer can verify configuration and change certain parameters (within defined ranges) by entering the ELECTRAfloConfiguration mode. This is accomplished using the four membrane pushbuttons located on the ELECTRA-flocover. See Figure 4.1 for location of pushbuttons.Air Monitor Corporation116-053-13.P65 (2/28/12)10ELECTRA-flo - IO&M Manual
Page 1: Installation, Operation,and Mainten
Page 5 and 6: ELECTRA-floINSTRUMENT WARRANTYINSTR
Page 7: ELECTRA-floSECTION 2 - PERFORMANCE
Page 10 and 11: ELECTRA-floSECTION 4 - INSTALLATION
Page 12 and 13: ELECTRA-floSECTION 4 - INSTALLATION
Page 16 and 17: ELECTRA-floSECTION 5 - OPERATION5.5
Page 34 and 35: ELECTRA-floSECTION 5 - OPERATIONAva
Page 36 and 37: ELECTRA-floSECTION 5 - OPERATIONAva
Page 38 and 39: ELECTRA-floSECTION 6 - CALIBRATION6
Page 44 and 45: ELECTRA-floSECTION 6 - CALIBRATIONS
Page 48 and 49: ELECTRA-floSECTION 7 - MAINTENANCE7
Page 50 and 51: ELECTRA-floSECTION 9 - PARTS LIST9
Page 52 and 53: ELECTRA-floAPPENDIX AAPPENDIX APROD
Page 54 and 55: ELECTRA-floAPPENDIX AANALOG INPUT O

ELECTRA-flo - V1.5x - 9-19-11.PMD - Air Monitor Corporation

Create successful ePaper yourself

Delete template?

Save as template?