I N S T A L L E Rmr.steam ®<strong>Installation</strong>, <strong>Operation</strong> & <strong>Maintenance</strong> <strong>Manual</strong>__________________________________________________________________________CONTROL INSTALLATIONRefer to Control <strong>Manual</strong> for specific installation requirementsBEFORE INSTALLINGTurn power to the steam generator OFF before connecting thecontrol to the generator. Failure to turn the power off will result inan inoperable control.! CAUTION To avoid unintentional steambath operation,do not locate the control where other controls, accessories,shower heads, valves, body sprays or similar within the showercould cause confusion or interfere with the Mr.Steam control’sintended use and function.! CAUTION Do not use any iSteam ® , iTempo/Plus ,iTempo , HomeWizard or iGenie ® controls without readingand understanding its own manual and the Mr.Steam steamgenerator <strong>Installation</strong> and <strong>Operation</strong> <strong>Manual</strong>. Failure to readand understand these instructions may result in an inoperativeor hazardous installation.! WARNING A peel and stick warning sticker must be readand permanently affixed in a conspicuous location near thesteam room. Failure to read and affix this warning sticker in aconspicuous location may result in serious injury or death. .Install the iSteam, iTempo or iTempo/Plus controls accordingto installation instructions. Failure to install according toinstructions will result in an inoperative control or hazardousoverheating or inadequate heating of the steam room.If an iSteam, iTempo or iTempo/Plus control is installed outsidethe steam room a Remote Temperature Probe (PN <strong>MS</strong>TSor i<strong>MS</strong>TS) must be installed inside the steam room per installationinstructions supplied with the Remote TemperatureProbe. Failure to install according to instructions will result inan inoperative control and overheating of the steam room.!WARNING Do not route iSteam, iTempo/Plus, iTempo,HomeWizard or iGenie control wiring inside conduittogether with power lines or close to hot water or steampiping. Doing so may result in an inoperative or hazardousinstallation. Do not alter or modify any Mr. Steam productsincluding the steam generator, iSteam, iTempo/Plus,iTempo, iGenie or HomeWizard controls. Doing so mayresult in an inoperative or hazardous installation and willvoid he warranty.IMPORTANT NOTES:1. Turn power to the steam generator OFF before connectingthe control to the generator. Failure to turn thepower off will result in an inoperable control.2. Do not operate iSteam, iTempo/Plus, iTempo,HomeWizard or iGenie controls with other than aMr.Steam iSteam or iTempo compatible steam generator.Mr.Steam residential steam generators with serialnumbers lower than 900000, or any other brand ofsteam generator are not to be operated with iTempocontrols. Doing so may result in an inoperative or hazardousinstallation. If iSteam is used with a generatorhaving serial number 900000 through 930030, contactMr.Steam technical support for an upgraded PC board.3. This document contains important safety, operation andmaintenance information. Leave this document with thehomeowner. Do not discard this document.4. Discontinue use of the steam generator or control if thesteam generator is damaged or otherwise not functioningproperly. Operating a damaged steam generatormay result in an inoperative or hazardous installationCONTROL ROUGH INRefer to <strong>Installation</strong> Instructions for the specific control1. Determine the desired installation location of the control.The iSteam ® , iTempo and iTempo/Plus controlsare designed to be installed inside or outside thesteam room as a matter of personal preference. If thecontrol is installed inside the steam room the controlmust be located:2. 4-5 feet above the floor near the bather seating area3. The control features an integral temperature sensor.Locate the control in a location representative of thedesired steambathing temperatures.Do not locate the control above or near the steamhead or direct steam emissions.4. on a vertical wallThe control cable length is 30 feet. Insure that the controland/or steam generator are located accordingly. Anoptional 60 foot cable is available, PN 103990-60 for iTempoand PN 104117-60 for iSteam. Contact a Mr. Steam technicalservice representative if a 60 foot cable is required.IMPORTANT NOTES:If the control is installed outside the steamroom a RemoteTemperature Probe Part Number <strong>MS</strong>TS or i<strong>MS</strong>TS must beinstalled inside the steam room, depending on the control.Insure Mr.Steam steam generator is iSteam or iTempo compatibleand has a serial number 900000 or higher. If iSteam is usedwith a generator having serial number 900000 through 930030,contact Mr.Steam technical support for an upgraded PC board.See instructions for the <strong>MS</strong>TS or i<strong>MS</strong>TS Temperature Probe(located in the Control <strong>Installation</strong> <strong>Manual</strong> related to your specificcontrol package) before rough-in or installation of control.18
mr.steam ®<strong>Installation</strong>, <strong>Operation</strong> & <strong>Maintenance</strong> <strong>Manual</strong>__________________________________________________________________________SAFETY AND OPERATING INFORMATION! WARNING Do not install or use any iSteam ® ,iTempo/Plus , iTempo , HomeWizard or iGenie ® controlswithout reading and understanding the Mr.Steam steamgenerator <strong>Installation</strong> and <strong>Operation</strong> <strong>Manual</strong>. Failure to readand understand these instructions may result in an inoperativeor hazardous installation.! WARNING The peel and stick warning sticker locatedin this manual must be read and permanently affixed in aconspicuous location near the steam room. Failure to readand affix this warning sticker in a conspicuous location mayresult in serious injury or death.Install the iSteam, iTempo or iTempo/Plus controls accordingto installation instructions. Failure to install according toinstructions will result in an inoperative control or hazardousoverheating or inadequate heating of the steam room.If an iSteam, iTempo or iTempo/Plus control is installedoutside the steam room a Remote Temperature Probe(PN <strong>MS</strong>TS or i<strong>MS</strong>TS) must be installed inside the steamroom per installation instructions supplied with theRemote Temperature Probe. Failure to install according toinstructions will result in an inoperative control andoverheating of the steam room.! CAUTION Do not route iSteam, iTempo/Plus, iTempo,HomeWizard or iGenie control wiring inside conduittogether with power lines or in proximity to hot water orsteam piping. Doing so may result in an inoperative orhazardous installation.Do not alter or modify any Mr. Steam products includingthe steam generator, iSteam, iTempo/Plus, iTempo, iGenieor HomeWizard controls. Doing so may result in an inoperativeor hazardous installation and will void the warranty.IMPORTANT NOTES: Do not operate iSteam, iTempo/Plus,iTempo, HomeWizard or iGenie controls with other than aMr.Steam iSteam or iTempo compatible steam generator.Mr.Steam residential steam generators with serial numberslower than 900000, or any other brand of steam generatorare not to be operated with iTempo controls. Doing somay result in an inoperative or hazardous installation. IfiSteam is used with a generator having serial number900000 through 930030, contact Mr.Steam technical supportfor an upgraded PC board. This document containsimportant safety, operation and maintenance information.Leave this document with the homeowner. Do not discardthis document.Malfunction due to power spikes, lightning, fire, freezingor flooding is not covered under the warranty.Discontinue use of the steam generator or control if thesteam generator is damaged or otherwise not functioningproperly. Doing so may result in an inoperative orhazardous condition.I N S T A L L E R19