Series 0.100 Cardan Drive-Shafts 0.100

0.100Cardan Drive-ShaftsRoller bearing versionSeries 0.100At utilisation of the nominal torque a verificationof the flange connection is necessary.On both sides standard flangeend number: 0.148.XX0On both sides larger flangeend number: 0.148.XX1ß = Maximum angle of deflection per jointJ m = Moment of inertiaG = WeightS min = Minimum length of tubular typesS 1 Compressed lengthsS =2 of short typesX 1 = Extension at S min resp. S 1X 2 = Extension at S 2P 1 = Tube diameter. Dimensions in boldtype for normal applications.Alternative dimensions are for longshafts at high speeds, see technicalannex domain speedP 2 = Alternative tubeP 3Universal Cardan Drive-Shafts with extensionPlease indicate requested length „S“ andmax. r.p.m. when ordering!Order numberAngle of deflection ß °Flange-ØmmS min resp. S 1mmS 2mmX resp. X 1mmX 2mmP 1mmP 2mmP 3mmSpline dim. DIN 5480mmNumber of flange holesJ m (at S min resp. S 1 ) kgm 2J m (at S 2 ) kgm 2J m /100 mm standard tube kgm 2G (at S min resp. S 1 )kgG (at S 2 )kgG/100 mm standard tube kgϕ (bei S min bzw. S 1 ) ∠°ϕ (bei S 2 ) ∠°ϕ/100 mm Normalrohr ∠°Tubular Typelarger extensionShort Type IShort Type II0.148.11020150550–110–80 x 490 x 4100 x 40.148.11120180550–110–80 x 490 x 4100 x 40.148.11235Hub812–110–80 x 490 x 4100 x 40.148.11535120/150580–110–80 x 490 x 4100 x 40.148.130201503604004080–––0.148.131201803604004080–––0.148.13220Hub6226624080–––0.148.14020150460–80––––0.148.14120180460–80––––0.148.14220Hub722–80––––0.148.14535120/150490–80––––55x2,5x20 55x2,5x20 55x2,5x20 55x2,5x20 55x2,5x20 55x2,5x20 55x2,5x20 55x2,5x20 55x2,5x20 55x2,5x20 55x2,5x2080,0323–0,0010920,87–0,753,6–0,2680,0342–0,0010922,17–0,753,6–0,26–0,0406–0,0010929,77–0,753,6–0,2680,0332–0,0010922,19–0,753,7–0,2680,02470,0267–15,6316,88–3,33,4–80,02670,0287–16,9316,55–3,33,4––0,034140,03614–24,5325,77–3,33,4–80,0294––18,37––3,5––80,0314––19,67––––––0,03884––27,27–––––80,0304––19,69–––––28• Catalog • Spare parts • Drive-Shaft Calculation • Installation and Maintenance • www.elbe-group.com

Size 0.148One keyway is not enough to transmitthe max. torque. In such case asecond keyway or an internal splineis recommended.Md Nom 5500 NmMd Lim 7050 Nm0.100Key-way accordingto DIN 6885 sheet 1On both sides connecting hubwithout key-way end number: 0.148.XX2with key-way end number: 0.148.XX3On both sides flange for larger angle deflectionend number: 0.148.XX5Cardan Drive-Shafts without extensionUniversal Joints without extensionTubular TypeUniversal Joint DoubleUniversal Joint Single0.148.20020150345–––80 x 490 x 4100 x 4–80,0217–0,0010914,53–0,753,2–0,260.148.20120180345–––80 x 490 x 4100 x 4–80,0237–0,0010915,83–0,75––0,260.148.20235Hub607–––80 x 490 x 4100 x 4––0,03144–0,0010923,43–0,75––0,260.148.20535120/150375–––80 x 490 x 4100 x 4–80,0227–0,0010915,85–0,75––0,260.148.30020150235–––––––80,0149––11,92––2,7––0.148.30120180235–––––––80,0161––13,22––2,7––0.148.30220Hub497––––––––0,0162––20,82––2,7––0.148.40020150130–––––––80,0106––6,75––2,1––0.148.40120180130–––––––80,0126––8,05––2,1––0.148.40235Hub392––––––––0,02004––15,54––2,1––0.148.40535120/150160–––––––80,0117––8,08––2,2––29• Service Phone North America •+1–269/6377999• Service Phone Europe •+49 (0) 71 42 / 353-0