ANSI ESD S20.20-2007 - FOIA and eLibrary website! - NASA

More documents

Recommendations

Info

ANSI/ESD S20.20-20074.0 DEFINITIONSThe terms used in the body of this document are in accordance with the definitions found in ESDADV1.0, ESD Association’s Glossary of Terms.5.0 PERSONNEL SAFETYThe procedures and equipment described in this document may expose personnel to hazardouselectrical conditions. Users of this document are responsible for selecting equipment thatcomplies with applicable laws, regulatory codes and both external and internal policy. Users arecautioned that this document cannot replace or supersede any requirements for personnel safety.Ground fault circuit interrupters (GFCI) and other safety protection should be consideredwherever personnel might come into contact with electrical sources.Electrical hazard reduction practices should be exercised and proper grounding instructions forequipment shall be followed.6.0 ESD CONTROL PROGRAM6.1 ESD Control Program RequirementsThe Program shall include both administrative and technical requirements as described herein.The most sensitive level of the items to be handled, in accordance with the Program, shall bedocumented. The Organization shall establish, document, implement, maintain and verify thecompliance of the Program in accordance with the requirements of this document.6.2 ESD Control Program Manager or CoordinatorAn ESD Control Program Manager or Coordinator shall be assigned by the Organization to verifythe compliance of the Program in accordance with the requirements of this document.6.3 TailoringThis document, or portions thereof, may not apply to all applications. Tailoring is accomplishedby evaluating the applicability of each requirement for the specific application. Upon completionof the evaluation, requirements may be added, modified or deleted. Tailoring decisions, includingrationale and technical justifications, shall be documented in the ESD Control Program Plan.7.0 ESD CONTROL PROGRAM ADMINISTRATIVE REQUIREMENTS7.1 ESD Control Program PlanThe Organization shall prepare an ESD Control Program Plan that addresses each of therequirements of the Program. Those requirements include:• Training• Compliance Verification• Grounding / Equipotential Bonding Systems• Personnel Grounding• EPA Requirements• Packaging Systems• MarkingCopyright 2010 by ESD Association. Licensed, by agreement, for enterpise-wide use to NASA.No other reproduction or transmission in any form is permitted without written permission of the ESDA.For inquiries or to report unauthorized use, contact info@esda.org.2
ANSI/ESD S20.20-2007The ESD Control Program Plan is the principal document for implementing and verifying theProgram. The goal is a fully implemented and integrated Program that conforms to internalquality system requirements. The ESD Control Program Plan shall apply to all applicable facetsof the Organization’s work.7.2 Training PlanInitial and recurrent ESD awareness and prevention training shall be provided to all personnelwho handle or otherwise come into contact with any ESDS items. Initial training shall be providedbefore personnel handle ESDS items. The type and frequency of ESD training for personnel shallbe defined in the Training Plan. The Training Plan shall include a requirement for maintainingemployee training records and shall document where the records are stored. Training methodsand the use of specific techniques are at the Organization’s discretion. The training plan shallinclude the methods used by the Organization to verify trainee comprehension and trainingadequacy.7.3 Compliance Verification PlanA Compliance Verification Plan shall be established to ensure the Organization’s fulfillment of thetechnical requirements of the ESD Control Program Plan. Process monitoring (measurements)shall be conducted in accordance with a Compliance Verification Plan that identifies the technicalrequirements to be verified, the measurement limits and the frequency at which thoseverifications shall occur. The Compliance Verification Plan shall document the test methods andequipment used for process monitoring and measurements. If the test methods used by theOrganization differ from any of the standards referenced in this document, then there must be atailoring statement that is documented as part of the ESD Control Program Plan. Complianceverification records shall be established and maintained to provide evidence of conformity to thetechnical requirements.The test equipment selected shall be capable of making the measurements defined in theCompliance Verification Plan.8.0 ESD CONTROL PROGRAM PLAN TECHNICAL REQUIREMENTSThe following sections, Sections 8.1 to 8.5, describe the key technical requirements used in thedevelopment of an ESD Control Program.The required limits are based on the test methods or standards listed in each table. TheCompliance Verification Plan shall document the methods used to verify the limits.8.1 Grounding / Equipotential Bonding SystemsGrounding / Equipotential Bonding Systems shall be used to ensure that ESDS items, personneland any other conductors (e.g., mobile equipment) are at the same electrical potential. Animplementing process shall be selected from Table 1.3Copyright 2010 by ESD Association. Licensed, by agreement, for enterpise-wide use to NASA.No other reproduction or transmission in any form is permitted without written permission of the ESDA.For inquiries or to report unauthorized use, contact info@esda.org.
Page 1 and 2: ANSI/ESD S20.20-2007Revision of ANS
Page 3 and 4: ESD Association Standards Committee
Page 5 and 6: ANSI/ESD S20.20-2007CAUTIONNOTICEEl
Page 7 and 8: ANSI/ESD S20.20-2007This document w
Page 9: ESD Association StandardANSI/ESD S2
Page 13 and 14: ANSI/ESD S20.20-20078.3 ESD Protect
Page 15 and 16: ANSI/ESD S20.20-20078.4 PackagingES
Page 17 and 18: ANSI/ESD S20.20-2007ANNEX B - ESD S
Page 19 and 20: ANSI/ESD S20.20-2007Table 5. ESD Su
Page 21: ANSI/ESD S20.20-2007Industry Standa

ANSI ESD S20.20-2007 - FOIA and eLibrary website! - NASA

Create successful ePaper yourself

Delete template?

Save as template?