ETAG 034 Edition July 2011 GUIDELINE FOR EUROPEAN ...

More documents

Recommendations

Info

Figure 1 – Example of distances between holesCLADDINGFIXINGSJOINTPROFILESPressure PressionFigure 2 - Example of test device – vertical sectionETAG 03430
Pression PressureCLADDINGJOINTFigure 3 - Example of test device – horizontal section5.3.2 Water permeability of cladding element (resistance to water diffusion)The test is not relevant due to the fact that only kits designed with ventilated air space areconsidered in this part.5.3.3 Water vapour permeabilityThe test is not relevant due to the fact that only kits designed with ventilated air space areconsidered in this part.5.3.4 DrainabilityThe drainability of a cladding kit is generally assessed by appraisal of design taking into accountof the characteristics of materials used and geometry of external cladding and joints.The cladding kit shall be designed and installed so that water which penetrates in the air spaceor condensation water shall be drained out of the installed kit without accumulation or moisturedamage or leakage into the substrate or the wall cladding kit.ETAG 03431
Page 1 and 2: European Organisation for Technical
Page 3 and 4: 5.3.5 Content and/or release of dan
Page 5 and 6: 9 THE ETA CONTENT .................
Page 7 and 8: Section one:INTRODUCTION1. PRELIMIN
Page 9 and 10: - Made with a render sprayed in sit
Page 11 and 12: A- Cladding kit consisting of cladd
Page 13 and 14: E- Cladding kit consisting of cladd
Page 15 and 16: The following table gives examples
Page 17 and 18: Walls made of concrete either cast
Page 19 and 20: Section two:GUIDANCE FOR THE ASSESS
Page 21 and 22: This chapter also takes into accoun
Page 23 and 24: This means that for ER3 the protect
Page 25 and 26: 4.5 ER5: PROTECTION AGAINST NOISENo
Page 27 and 28: Table 2 - Verification of performan
Page 29: 5.2.2 Reaction to fire on back side
Page 33 and 34: µm, a diameter less than 3 µm and
Page 35 and 36: * for cladding elements which are m
Page 37 and 38: Data logger measures valueSKINFIXIN
Page 39 and 40: Observations during the testFailure
Page 41 and 42: Figure 7 - Example of test on fixin
Page 43 and 44: The failure load in N and the defor
Page 45 and 46: 5.4.2.3 Family CFigure 11 - Example
Page 47 and 48: The deflection of the profile shall
Page 49 and 50: 5.4.2.6 Family F5.4.2.6.1 Resistanc
Page 51 and 52: The cladding kit shall be capable o
Page 53 and 54: - The surface finish of the kit is
Page 55 and 56: The tests shall be carried out unde
Page 57 and 58: * EN 755-2 Aluminium and aluminium
Page 59 and 60: 6 ASSESSING AND JUDGING THE FITNESS
Page 61 and 62: 6.2.3 Fire resistanceNot relevant6.
Page 63 and 64: 6.4.1.1 Wind suctionThe load Q for
Page 65 and 66: 6.4.3 Resistance to horizontal poin
Page 67 and 68: • The 5%-fractile values (for a c
Page 69 and 70: The installation of the kit shall b
Page 71 and 72: The systems of attestation of confo
Page 73 and 74: For system 2+, this work shall be t
Page 75 and 76: • Cladding elementCharacteristicL
Page 77 and 78: Section four:ETA CONTENT9 THE ETA C
Page 79 and 80: “In addition to the specific clau
Page 81 and 82:
A.2.2Serviceability (of works)Abili
Page 83 and 84:
A.4.6Durability (of products)Abilit
Page 85 and 86:
EN 13238 (May 2001)Reaction to fire
Page 87 and 88:
EN ISO 179-2 (June 1999) Plastics -
Page 89 and 90:
Polyester panelsEN ISO 10352 (Decem
Page 91 and 92:
C.1.3HardnessDetermination of the h
Page 93 and 94:
Annex E:MOUNTING AND FIXING PROVISI
Page 95 and 96:
2.1 Family A, BThe panels can be cu
Page 97 and 98:
2.5 Family GThe cladding elements c
show all

ETAG 034 Edition July 2011 GUIDELINE FOR EUROPEAN ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?