11.07.2015 Views

LCR METER MODEL 11021/11021-L - Chroma Systems Solutions

LCR METER MODEL 11021/11021-L - Chroma Systems Solutions

LCR METER MODEL 11021/11021-L - Chroma Systems Solutions

SHOW MORE
SHOW LESS
  • No tags were found...

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

Lower Harmonic-distortionPhase-detection TechnologyThe <strong>11021</strong>/<strong>11021</strong>-L uses lower harmonic-distortion phasedetectiontechnology to reduce affection of measurementaccuracy caused by hysteresis distortion in magneticcomponent or high dielectric-coefficient capacitormeasurement, which is not provided in general low-end<strong>LCR</strong> meters. General low-end <strong>LCR</strong> meters use half periodintegration method as phase detector. The <strong>11021</strong>-L isthe ideal selection for high frequency coil, core, choke,ect passive components incoming/outgoing materialquality inspect and automatic production. The frequencyspectrum of half period square wave is shown as figure1 and 2, which non-ignorable 3 rd , 5 th order harmonics areincluded. For non-linear devices under testing, odd-order(3 rd , 5 th , 7 th , etc.) harmonics may occur in measured potentialor current signals. Then, this phase-detection methodwill cause obvious accuracy error because of same loworder harmonics are included in both unknown signal andphase-detect signal. The <strong>11021</strong>/<strong>11021</strong>-L uses eight stepssine-wave multiplier as phase detector to reduce low-orderharmonics affection to an ignorable level.Figure 1The frequency spectrum ofhalf period square wave(general low-end <strong>LCR</strong> meters)Figure 2Non-ignorable 3 rd , 5 thorder harmonics(<strong>11021</strong> uses eight steps sin-wave multiplier)SPECIFICATIONSModel <strong>11021</strong> <strong>11021</strong>-LMeasurement ParameterPrimary DisplayL, C, R, |Z|Secondary DisplayQ, D, ESR, Xs, Test Signals InformationTest Level 0.25V / 1V , ± (10% + 3 mV) 50 / 1V , ± (10% + 3 mV)Test Frequency100Hz, 120Hz, 1kHz, 10kHz(9.6kHz)1kHz, 10kHz, 40kHz, 50kHzFrequency Accuracy ±0.25% ±0.02%O u t p u t I m p e d a n c e(Typical)Varies as range resistors 25, 100, 1K, 10K, 100KMeasurement Display RangePrimary ParameterL: 0.01µH ~ 9.999kH, C: 0.01pF ~ 99.99mF,R,lZl: 0.1m. ~ 99.99MSecondary ParameterQ: 0.1 ~ 9999.9, D: 0.0001 ~ 9999.9, : -180.00˚~ +180.00˚Basic Accuracy *1 ±0.1% ±0.2%Measurement Time (1KHz) *2FastFreq = 1K/10KHz : 75mSFreq = 100/120Hz: 85mSFreq = 1KHz/10KHz : 75mSFreq = 40KHz : 105mSFreq = 50KHz : 90mSMedium 145mS *3Slow 325mS *4TriggerInternal, Manual, External, BusDisplayL, C, R, |Z|, Q, D, R, 40 x 4 (Character Module) LCD DisplayFunctionCorrectionOpen/Short zeroingEquivalent Circuit ModeSeries, ParallelInterface & Input/OutputInterfaceRS-232 (standard), Handler & GPIB (optional)Output SignalBin-sorting & HI/GO/LOW judgeComparatorUpper/Lower limits in valueBin Sorting 8 bin limits in %Trigger Delay0 ~ 9999mSGeneralOperation EnvironmentTemperature : 10˚C ~ 40˚C, Humidity < 90 % R.H.Power Consumption50VA max.Power Requirement90 ~ 125Vac or 190 ~ 250Vac, 48 Hz ~ 62 HzDimension (H x W x D)100 x 320 x 206.4 mm / 3.94 x 12.6 x 8.13 inchWeight4 kg / 8.81 lbsAll specifications are subject to change without notice.Note*1 : 23±5˚C after OPEN and SHORT correction, slow measurement speed. Refer to operationmanual for detail measurement accuracy descriptionsNote*2 : Measurement time includes sampling, calculation and judge test parameter measurementNote*3 : Freq.=1KHz/10KHz 145ms ; Freq.=40KHz 185ms ; Freq.=50KHz 150msNote*4 : Freq.=1KHz/10KHz 325ms ; Freq.=40KHz 415ms ; Freq.=50KHz 400msPANEL DESCRIPTIONORDERING INFORMATION31141 2 6 7 8510 91512 14 131. LCD Display2. Function Keys3. Power Switch4. Ground Terminal5. Unknown Test Terminals6. Meas Display Key7. Main Indx Key8. System Setup Key9. Trigger Key10. Cursor Keys11. RS232 Interface12. Power Voltage Selector13. AC Line Input14. Fuse15. GPIB and Handler Interface<strong>11021</strong> : <strong>LCR</strong> Meter 1kHz<strong>11021</strong> : <strong>LCR</strong> Meter 10kHz<strong>11021</strong>-L : <strong>LCR</strong> MeterA110104 : SMD Test Cable #17A<strong>11021</strong>1 : Component Test FixtureA<strong>11021</strong>2 : Component Remote Test FixtureA110232 : 4 BNC Test Cable with Clip #18A110234 : High Frequency Test CableA110235 : GPIB & Handler InterfaceA110236 : 19" Rack Mounting KitA110242 : Battery ESR Test KitA133004 : SMD Test BoxA165009 : 4 BNC Test Cable with ProbeDeveloped and Manufactured by :CHROMA ATE INC.致 茂 電 子 股 份 有 限 公 司 CHINAHEADQUARTERSCHROMA ELECTRONICSNo. 66, Hwa-Ya 1st Rd., (SHENZHEN) CO., LTD.Hwa-Ya Technology Park, 8F, No.4, Nanyou Tian AnKuei-Shan Hsiang,33383 Industrial Estate, Shenzhen,Taoyuan County, Taiwan China PC: 518052Tel: +886-3-327-9999 Tel: +86-755-2664-4598Fax: +886-3-327-8898 Fax: +86-755-2641-9620http://www.chromaate.comE-mail: chroma@chroma.com.twJAPANCHROMA JAPAN CORP.11F NARA Building II 2-2-8Shinyokohama, Kouhokuku,Yokohama City 222-0033Kanagawa, JapanTel: +81-45-470-2285Fax: +81-45-470-2287http://www.chroma.co.jpU.S.A.CHROMA ATE INC. (U.S.A.)7 Chrysler Irvine, CA 92618Tel: +1-949-421-0355Fax: +1-949-421-0353Toll Free: +1-800-478-2026http://www.chromaus.comE-mail: info@chromaus.comEUROPECHROMA ATE EUROPE B.V.Morsestraat 32, 6716 AH Ede,The NetherlandsTel: +31-318-648282Fax: +31-318-648288http://www.chromaeu.comE-mail: sales@chromaeu.comDistributed by:Worldwide Distribution and Service Network<strong>11021</strong>/<strong>11021</strong>-L-E-201008-1000

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!