USDA Irrigation System, Sprinkler - 442 KS-ENG-201 NRCS (Center ...
USDA Irrigation System, Sprinkler - 442 KS-ENG-201 NRCS (Center ...
USDA Irrigation System, Sprinkler - 442 KS-ENG-201 NRCS (Center ...
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>USDA</strong> <strong>Irrigation</strong> <strong>System</strong>, <strong>Sprinkler</strong> - <strong>442</strong> <strong>KS</strong>-<strong>ENG</strong>-<strong>201</strong><strong>NRCS</strong> (<strong>Center</strong> Pivot) Rev. 1/11NameLegal Desc.Designed byChecked byApproved byIdent. No.CountyDateDateDate<strong>System</strong> Requirements and InformationWater Right gallons per minute (gpm) Irrigated Area acresPump Design Flow Rate (Based on Pump Test) 1/ gpmMinimum Wetted Diameter of Outside <strong>Sprinkler</strong> Required feet<strong>System</strong> Length feet <strong>System</strong> Capacity gpm (Without End Gun or Cornering <strong>System</strong>)Ground Elevations: Maximum Minimum At the PivotLocation of Maximum Ground Elevation (If Not at End of Pivot)<strong>Sprinkler</strong> Placement: On the Pipe Below Truss Rod and Above CanopyIn Canopy Above 30 Inches 12 to 30 Inches AbovegroundTypical <strong>Sprinkler</strong> Height Aboveground feet Height of the Pivot feetMark Attached Items:Plan Map of <strong>System</strong>Form <strong>KS</strong>-<strong>ENG</strong>-22, <strong>Irrigation</strong> <strong>System</strong>, <strong>Sprinkler</strong> - <strong>442</strong> (<strong>Center</strong> Pivot <strong>Sprinkler</strong> Design)Form <strong>KS</strong>-<strong>ENG</strong>-394, <strong>Irrigation</strong> Water Management - 449 (Planned Crop and Water Requirement)Remarks:1/ If there hasn’t been a pump test run during the irrigation season within the most recent 3-year period,the design flow rate will not be greater than 80 percent of the original pump flow rate.
<strong>KS</strong>-<strong>ENG</strong>-<strong>201</strong>Page 2Supplier/dealer shall submit a computer printout showing the following items--at least 14 days prior toinstallation: (Mark items that are on the computer printout.)<strong>Sprinkler</strong> LocationsPipe PressuresNozzle Sizes, Drop HeightsFriction Loss C FactorsTimerSettings<strong>Sprinkler</strong> Flow Rates<strong>Sprinkler</strong> PressureSize and Pressure Rating of RegulatorsLateral Outside DiametersField Elevation Drop and Gain (in feet) to Ensure All Design Requirements Are Met Prior toInstallationDocumentation of the Coefficient of Uniformity (CU) ProvidedIs the sprinkler design printout attached? Yes NoDoes the sprinkler design meet required design criteria? Yes NoFailure to provide the computer printout prior to installation may jeopardize any pending cost-shareassistance.Item Designed As InstalledCoefficient of Uniformity (CU)<strong>Sprinkler</strong> Type and ManufacturerNumber of <strong>Sprinkler</strong>sNumber of Pressure RegulatorsPressure Regulator Rating (psi)<strong>Sprinkler</strong> Height Aboveground (feet)Wetted Diameter of Outer Nozzle (feet)<strong>Center</strong> Pivot ManufacturerNumber of TowersLength of <strong>System</strong> Lateral (feet)Outside Diameters (O.D.) of <strong>System</strong>Lateral (inches)percentDoes the checkout of the system installation agree with the design? Yes NoIf not, explain why:Checkout byAudited byDateDate
Change language