Installation Instructions VITOCELL r 100-V - Viessmann

More documents

Recommendations

Info

4 Safety Important Regulatory and Installation Requirements Codes The installation of indirect-fired hot water storage tanks in boilers and solar system application might be governed by individual local rules and regulations for this type of product, which must be observed. Always use latest editions of codes. In the Commonwealth of Massachusetts, all plumbing work must be done by a licensed plumber or gas-fitter and for gas installations, all gas piping must be done by a licensed gas-fitter. Mechanical room Ensure the mechanical room complies with the requirements of the system design guideline and/or Technical Data Manual (available from your Viessmann sales representative). The tank must be installed in a mechanical room which is never subject to freezing temperatures. Ensure water in tank is drained if not in use and danger of freezing exists in the mechanical room. WARNING If the heating system itself is to be filled with Glycol or any other antifreeze, the system fill must be of non-toxic or food grade antifreeze. In any circumstance, a non-toxic fluid must be used. Ensure a copy of the Material Safety Data Sheet (MSDS) is supplied to the operator/ultimate owner of the system. The use of Viessmann supplied “Tyfocor-HTL” solar fill is recommended for the solar heating circuit. Working on the equipment The installation, adjustment, service, and maintenance of this equipment must be done by a licensed professional heating contractor who is qualified and experienced in the installation, service, and maintenance of hot water heating systems. There are no user serviceable parts on this equipment. Ensure main power supply to equipment, the heating system, and all external controls has been deactivated. Close main oil or gas supply valve. Take precautions to avoid accidental activation of power during service work. Technical literature Literature applicable to all aspects of the Vitocell: - Technical Data Manual - Installation Instructions - Start-up/Service Instructions - Operating Instructions and User’s Information Manual Vitocell 100-V Installation Instructions �Please carefully read this manual prior to attempting installation. Any warranty is null and void if these instructions are not followed. This product must be installed observing not only the information and instruction provided in the pertinent product literature (see list on following page), but also all local, provincial/state plumbing and building codes, as they apply to this product and all periphery equipment. For information regarding other Viessmann System Technology componentry, please reference documentation of the respective product (available from your Viessmann sales representative). We offer frequent installation and service seminars to familiarize our partners with out products. Please inquire. �The completeness and functionality of field supplied electrical controls and components must be verified by the heating contractor. These include low-water cut-offs, flow switches (if used), staging controls, pumps, motorized valves, air vents, thermostats, temperature controls, etc. �Leave all literature at the installation site and advise the system operator/ultimate owner where the literature can be found. Contact Viessmann for additional copies. 5608 487 v1.2
About These Instructions Take note of all symbols and notations intended to draw attention to potential hazards or important product information. These include “WARNING”, “CAUTION”, and “IMPORTANT”. See below. WARNING Indicates an imminently hazardous situation which, if not avoided, could result in substantial product/property damage, serious injury or loss of life. CAUTION Indicates an imminently hazardous situation which, if not avoided, may result in minor injury or product/property damage. � IMPORTANT Product Information 42 USG to 120 USG (160 L to 450 L) capacity Enameled indirect-fired domestic hot water storage tank with one heat exchanger coil for use with hot water heating boilers, residential/commercial heating plants, and lowtemperature heating systems. These tank versions are not suitable for steam heating applications. 5608 487 v1.2 Vitocell 100-V Installation Instructions General Information �Warnings draw your attention to the presence of potential hazards or important product information. �Cautions draw your attention to the presence of potential hazards or important product information. �Helpful hints for installation, operation or maintenance which pertain to the product. �This symbol indicates that additional, pertinent information is to be found. �This symbol indicates that other instructions must be referenced. 5
Page 1 and 2: Installation Instructions for use b
Page 3: Introduction Safety General Informa
Page 7 and 8: Tank Set-up - For narrow passageway
Page 9 and 10: 42 to 79 USG (160 to 300 Liter) Tan
Page 11 and 12: 120 USG (450 Liter) Tank Installati
Page 13 and 14: 120 USG (450 Liter) Tank Installati
Page 15 and 16: Boiler Water Connections (heat exch
Page 17 and 18: Domestic Water Connections (continu
Page 19 and 20: Multiple Tank Set-up [only for 79 a
Page 21 and 22: Vitocell 100-V Installation Instruc
Page 23 and 24: 5608 487 v1.2 Vitocell 100-V Instal

Installation Instructions VITOCELL r 100-V - Viessmann

Create successful ePaper yourself

Delete template?

Save as template?