Marmitek X-10 product guide Marmitek X-10 product guide

More documents

Recommendations

Info

26 26 TECHNICAL INFORMATION ART. NR. 08934 PHASE COUPLING FILTER FD10 COUPLING AND FILTERING OUTGOING PHASES INCOMING PHASES Power: 30V +10% -15%, 50Hz Maximum load: 63A Central Filtering Frequency: 120kHz Filter Bandwidth: 5kHz min. (3dB points) Forward Attenuation: 20dB min. at I = 0A 15dB min. at I = 63A Reverse Attenutation: 15dB min. Input impedance: 20_ min. at f=120kHz Coupling loss: 2dB max. at f=120kHz Terminals: Screw connectors for phase (in), phase (out) neutral and coupling Dimensions wxhxl: 35x80x65mm (2e wide) Ambient Temperature: -10°C to 50°C (operating), -20°C to 70°C (storage) TURN OFF THE ELECTRICITY BEFORE INSTALLING THE MODULE! Coupling without filtering The FD10 Phase Couple Filter can also be used as signal coupler only. This has two practical advantages: 1 The phases do not need to be fed through the filters, this makes installation a lot easier. 2 The maximum currents through the filters are not restricted to 63A. The filter is connected in parallel to the phases, so that it is only used for X-10 signals. COUPLING WITHOUT FILTERING OUTGOING PHASES INCOMING PHASES
MARMITEK ART. NR. 09055 PLUG-IN FILTER FM10 Plug-In Filter to filter noise from TVs, photo copiers, motors, power appliances, etc. To prevent absorbtion of Marmitek X-10 PLC (Power Line Carrier) signals by appliances that reduce these PLC signals. APPLICATION: Transmission of high-frequency signals via the mains, like the Marmitek X-10 signals, can be influenced by equipment plugged into the mains electricity system. Some appliances reduce the amplitude of the modulated signal or can negatively influence the impedance of the mains. By using active filtering in Marmitek X-10 modules this problem can be prevented in small-scale home installations. Certain appliances with badly dimensioned switching power supplies can however influence the system (e.g. TVs). In buildings where distances are bigger, this problem can occur quite easily, mainly because of the large number of machines (such as photo copiers, printers, etc.). For these situations the FM10 Plug-In Filter is the ideal solution: just place the filter between the equipment and the wall socket to make sure the appliance does not influence the performance of the PLC system. HOME AUTOMATION 27
Page 1 and 2: HOME TOMATIO AUTOMATION Marmitek X-
Page 3 and 4: MARMITEK HOME AUTOMATION MARMITEK X
Page 5 and 6: der control! On the left you see so
Page 7 and 8: MARMITEK HOME AUTOMATION KITS CM11
Page 9 and 10: MARMITEK ART. NR. 08910 LAMP MODULE
Page 11 and 12: MARMITEK ART. NR. 08915 APPLIANCE M
Page 13 and 14: MARMITEK ART. NR. 08944 UNIVERSAL R
Page 15 and 16: MARMITEK ART. NR. 08930 WALL DIMMER
Page 17 and 18: MARMITEK ART. NR. 08931 WALL SWITCH
Page 19 and 20: MARMITEK ART. NR. 08954 SHUTTER SWI
Page 21 and 22: MARMITEK ART. NR. 08932 DIN RAIL DI
Page 23 and 24: MARMITEK ART. NR. 08933 DIN SWITCH
Page 25: MARMITEK ART. NR. 08934 PHASE COUPL
Page 29 and 30: MARMITEK ART. NR. 08941 MINI CONTRO
Page 31 and 32: MARMITEK ART. NR. 08939 MINI TIMER
Page 33 and 34: MARMITEK ART. NR. 08945 PC INTERFAC
Page 35 and 36: MARMITEK ART. NR. 08943 UNIVERSAL A
Page 37 and 38: MARMITEK ART. NR. 08942 TTL/CMOS IN
Page 39 and 40: MARMITEK ART. NR. 09196 TRANSCEIVER
Page 41 and 42: MARMITEK ART. NR. 09434 HOME AUTOMA
Page 43 and 44: MARMITEK ART. NR. 08937 WIRELESS SW
Page 45 and 46: MARMITEK ART. NR. 09053 WIRELESS MO
Page 47 and 48: MARMITEK ART. NR. 09190 Wireless Re
Page 49 and 50: MARMITEK ART. NR. 08972 MULTIMEDIA
Page 51 and 52: MARMITEK XCAM XCAM2 Install your ow

Marmitek X-10 product guide Marmitek X-10 product guide

Create successful ePaper yourself

Delete template?

Save as template?