scope of accreditation to iso/iec 17025:2005 & ansi/ncsl z540-1 ...

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005& ANSI/NCSL Z540-1-1994 & ANSI/NCSL Z540.3-2006INSTRUMENT RENTAL LABS2100 W. 6th Ave.Broomfield, CO 80020Everett Hedrick Phone: 303 469 5335CALIBRATIONValid until: May 31, 2015 Certificate Number: 3104.01In recognition of the successful completion of the A2LA evaluation process, accreditation is granted tothis laboratory to perform the following calibrations 1 :I. Electrical – DC/Low FrequencyParameter/Equipment Range CMC 2, 3 () CommentsDC Voltage –Generate & MeasureUp to 220 mV(0.22 to 2.2) V(2.2 to 11) V(11 to 22) V(22 to 220) V(220 to 1100) V(1.0 to 40) kV34 µV/V21 µV/V21 µV/V9.3 µV/V10 µV/V14 µV/V0.18 %Fluke 5720A-03WBFluke 289Ross Eng. HV dividerDC Current –Generate & MeasureUp to 220 µA(0.22 to 2.2) mA(2.2 to 22) mA(22 to 220) mA(0.22 to 1.1) A0.011 %71 μA/A71 μA/A0.018 %0.019 %Fluke 5720A-03WB(1.1 to 20.0) A0.58 %Fluke 5520A& 50 A shunt(A2LA Cert. No. 3104.01) 06/03/2013 Page 1 of 6

Parameter/Equipment Range CMC 2, 3 () CommentsDC Resistance –Generate & MeasureFixed Points1 Ω10 Ω100 Ω1 k Ω10 k Ω62 µΩ/Ω33 µΩ/Ω32 µΩ/Ω20 µΩ/Ω19 µΩ/ΩFluke-742A-1IET-SRX-10IET-SRX-100Fluke-742A-1KFluke-742A-10K1 Ω(>1 to 100) Ω(>0.10 to 1.0) kΩ(>1.0 to 10) kΩ(>10 to 100) kΩ(>0.10 to 1.0) MΩ(1 to 100) MΩ(100 to 300) MΩ0.047 %49 µΩ/Ω74 µΩ/Ω20 µΩ/Ω21 µΩ/Ω39 µΩ/Ω0.083 %0.87 %Fluke 5720AAGILENT 3458A-02(0.30 to 1.0) GΩ0.018 %HTE-1 GOhmFluke 5522AAgilent 3458A-02Parameter/Range Frequency CMC 2, 3 () CommentsAC Voltage –Generate & Measure(22 to 220) mV(0.22 to 2.2) V(2.2 to 22) V(2.2 to 22) V1 kHz20 kHz20 kHz100 kHz0.028 %0.017 %33 µV/V0.082 %Fluke 5720A-03WB,Agilent 3458A-02(10) V100Hz to 1MHz0.09 %(700) V30 kHz0.19 %Fluke 5720A-03WB,Fluke 5725A amplifier(1 to 15) kV60 Hz0.13 %Fluke 289Ross Eng. HV divider(A2LA Cert. No. 3104.01) 06/03/2013 Page 2 of 6

Parameter/Range Frequency CMC 2, 3 () CommentsAC Current –Generate & MeasureUp to 0.220 mA(0.22 to 2.2) mA(2.2 to 22) mA(22 to 220) mA(0.22 to 2.2) A100 Hz to 10 kHz100 Hz to 10 kHz100 Hz to 10 kHz100 Hz to 10 kHz100 Hz to 10 kHz0.37 %0.21 %0.22 %0.41 %0.65 %Fluke 5720A-03WBAgilent 3458A-02Fluke 5520A, Agilent3458A-02(2.2 to 11 ) A40 Hz to 10 kHz0.15 %Fluke 5720A-03WB w/Fluke 5725A amplifier& Fluke 289 meter(11 to 3000 ) A60 Hz0.94 %Fluke 5520A, Agilent3458A-02HTE multi-turn coilsFluke Flexi i3000s ampRogowski air cored coilCapacitance –Generate & MeasureFixed Points(1.0, 10, 100,1000) pF1 kHz1.1 %Capacitor Set, HP16380A with InstekLCR-81710 nF to 10 000 µFAt various frequenciesranging anywherefromDC to 1 kHz0.78 %Fluke 5520A calibratorwith Instek LCR-817meterInductance –Generate & Measure1 mH100 mH1 H(0.1 to 10) kHz(0.1 to 10) kHz(0.1 to 1) kHz0.13 %0.13 %0.15 %Genrad 1482 seriesstandard inductorsInstek 817 LCR meter(A2LA Cert. No. 3104.01) 06/03/2013 Page 3 of 6

Parameter/Equipment Range CMC 2, 3 () CommentsElectrical Calibration ofThermocouples –Thermocouple SimulationGenerate & MeasureJ-Type(-210 to -100) ºC(-100 to -30) ºC(-30 to 150) ºC(150 to 760) ºC(760 to 1200) ºC0.27 ºC0.18 ºC0.16 ºC0.19 ºC0.25 ºCFluke 5520AK-Type(-200 to -100) ºC(-100 to -25) ºC(-25to 120) ºC(120 to 1000) ºC(1000 to 1372) ºC0.35 ºC0.20 ºC0.18 ºC0.28 ºC0.42 ºCT-Type(-250 to -150) ºC(-150 to 0) ºC(0 to 120) ºC( 120 to 400) ºC0.65 ºC0.26 ºC0.18 ºC0.16 ºCESD Impulse – Measure Voltage: (1 to 30) kV 3.8 % Agilent 54845Aoscilloscope calibrator,EMC partner ESDVeri-V, target 2-DN,Agilent 34401A DMMOscilloscope –Rise Time 150 ps 39 ps Fluke 9500B, activehead 9530 , Tek 694CoscilloscopeII. Electrical – RF/MicrowaveParameter/Range Frequency CMC 2 () CommentsRF Power LowFrequency – Generate& Measure0.1 Hz to 100 kHz 0.023 V RMS Agilent 3325Bsynthesized signalgenerator, Agilent3458A-02 DMM(A2LA Cert. No. 3104.01) 06/03/2013 Page 4 of 6

Parameter/Range Frequency CMC 2 () CommentsRF Power – Low toMedium FrequencyGenerate & Measure(-56 to +24) dBm(1mV to 10 V)(0.1 to 20) MHz 0.095 V RMS Agilent 3325Bsynthesized signalgenerator,HP8902A-050measuring receiver,HP 11722A sensorRF Power –Generate & Measure(-5 to -85) dBm1 GHz0.69 dBmHP 8902A-050measuring receiver;11793A microwaveconverter; HP 8340Bsynthesizer-assetHTE0333 only)w/ 11722A sensor(-5 to -85) dBm7 GHz1.2 dBmw/ 11792A sensor(-5 to -85) dBm12.4 GHz1.4 dBmw/ 11792A sensor(-5 to -85) dBm20 GHz & 26 GHz2.1 dBmw/ 11792A sensorRF Attenuation TunedRF Level – Generate &Measure(10 to 100 dB) 10 MHz50 MHz1 GHz4 GHz10 GHz15 GHz18 GHz0.53 dB0.55 dB0.63 dB0.50 dB0.94 dB1.4 dB0.51 dBAgilent 8902A-050measuring receiverAgilent 11793Amicrowave converter,HP 8496B / 8494Bstep attenuatorsw/ Agilent 11722Asensorw/ 11792A powersensor(A2LA Cert. No. 3104.01) 06/03/2013 Page 5 of 6

Parameter/Range Frequency CMC 2 () CommentsPhase Noise –Measure10 MHz to 1 GHz(2 to 18) GHz2.7 dBc/Hz3.0 dBc/HzHP 3048A phasenoise test setHP/Agilent 11848A,11729C, 3561A,3585A, HP 8663AFluke 9640A-LPN& HP 8340BIII. Time & FrequencyParameter/Equipment Range CMC 2 () CommentsFrequency –Measuring Equipment (1.0 to 26.5) GHz 5.0 parts in 10 12 Agilent 5071A (cesiumbeam), Agilent 8340Bsynthesized sweeperFrequency –Measure10 Hz to 40 GHz 1 Hz Agilent 5071A (cesiumbeam), HP 5352B-010________________________________1 This laboratory offers commercial calibration service.2 Calibration and Measurement Capability (CMC) is the smallest uncertainty of measurement that alaboratory can achieve within its scope of accreditation when performing more or less routinecalibrations of nearly ideal measurement standards or nearly ideal measuring equipment. Calibrationand Measurement Capabilities represent expanded uncertainties expressed at approximately the 95 %level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of aspecific calibration performed by the laboratory may be greater than the CMC due to the behavior ofthe customer’s device and to influences from the circumstances of the specific calibration.3Unless listed otherwise stated, all CMCs stated in percent are in percent of reading(A2LA Cert. No. 3104.01) 06/03/2013 Page 6 of 6

A2LA has accreditedINSTRUMENT RENTAL LABSBroomfield, COfor technical competence in the field ofCalibrationThis laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General Requirements forthe Competence of Testing and Calibration Laboratories. This laboratory also meets the requirements of ANSI/NCSLI Z540-1-1994 and therequirements of ANSI/NCSLI Z540.3-2006 and any additional program requirements in the field of calibration. This accreditationdemonstrates technical competence for a defined scope and the operation of a laboratory quality management system(refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009).Presented this 3 rd day of June 2013._______________________President & CEOFor the Accreditation CouncilCertificate Number 3104.01Valid to May 31, 2015For the calibrations to which this accreditation applies, please refer to the laboratory’s Calibration Scope of Accreditation.