Calibration of Liquid-in-Glass ThermometersThermometer Calibration Bath• Calibrates thermometers, temperature controllers and other temperatureinstruments against a factory certified thermometer traceable toNIST standards• Verifies accuracy of routine thermometers• For temperatures between ambient to 200°C (–30°C with the use ofcirculated refrigerated coolant)• Digital temperature control with temperature uniformity of ±0.02°C• Built-in ice bath for performing ice point calibrations• Meets the requirements of NBS Monograph 150<strong>Co</strong>nstant temperature calibration bath for liquid-in-glass thermometers,dial thermometers, digital thermometers and other temperaturemeasuring instruments. <strong>Co</strong>nsists of an oil bath with digital electroniccontrol providing temperature uniformity of ±0.02°C in the range –30°Cto +200°C. Accessory Standard Thermometer is calibrated and certifiedtraceable to NIST standards. Turntable rack inserts in bath to immerse sixthermometers or temperature probes and the standard thermometer.Bath depth of 12" (30.5cm) accommodates all partial immersionthermometers and most 15" total immersion thermometers.Features digital setpoint and display (°C/°F switchable) of bath temperaturefor maximum convenience, and overtemperature control to preventaccidental overheating. Built-in cooling coil permits circulation of tapwater or refrigerated coolant to permit operation at sub-ambienttemperatures or to facilitate rapid cool down for multi-point calibrations.Equipped with drains for oil bath and ice bath.Dimensions: lxwxh,in.(cm)28x24x21(71x61x53)Net Weight: 52 3 ⁄4 lbs (23.9kg)Shipping InformationShipping Weight: 66 lbs (30kg)Dimensions: 8.2 Cu. ft.SpecificationsTemperature Range: –30°C to +200°CFor sub-ambient temperatures, refrigerated recirculating coolantis required from an external source.Temperature Uniformity: ±0.02°CTemperature Limit <strong>Co</strong>ntrol: –16.7°C (30°F) above setpoint and204°C (400°F) maximumHeater Range: 0-750WCirculator: 1 ⁄20 hp impellerWorking Depth: Oil Bath: 12" (30.5cm)Ice Bath: 10 1 ⁄2" (26.7cm)Electrical Requirements:115V 60Hz220-240V 50/60HzCatalog No.K26500K26590K26501Ordering InformationOrder QtyThermometer Calibration Bath,115V 60Hz 1Thermometer Calibration Bath,220-240V 50/60HzAccessoriesStandard Thermometer,certified traceable to NIST Standards 1at 0, 20, 37, 56, 80, 100, 121, 140,160, 180 and 200°CK26503 Thermometer Magnifier(10X) 1K26502 Thermometer Carrying Case, 1holds K26501 Standard ThermometerpH MeterThis bench-top pH meter is an ideal help in every laboratory for routine or R&Dlevel measurement. This instrument measures pH, mV and has 40- point datamemory storage. <strong>Instrument</strong> has two operating modes -1. Standard mode2. GLP mode: 40 data readings can be stored, printed and scanned on display.For GLP mode, additional entries of sample name and ID number can bestored.The optional Data logging function enables the user to store 24 data pointsconsisting of pH, temperature and time readings. For example, as required inkinetic study or in any chemical reaction. Time intervals from 1min. to 1Hr. insteps of 1min. are available. User entries of pH limit values make the data moredefined and informative.<strong>Co</strong>nductivity Meter<strong>Koehler</strong> offers the perfect choice of a bench top conductivity meter formeasurements in the laboratory - whether routine or at the R & D level. Theconductivity meter offers better operating comfort and measuring confidencein all areas of application. Due to a user selective temperature function, theinstrument calculates the conductivity at the reference temperature 25 ± 0.1°Cwith a linear function.<strong>Co</strong>nductivity is an important factor in water analysis for quality of drinkingwater, direct ionic concentration measurement in pharmaceutical preparations,waste water treatment plants, pollution control in lakes & rivers, boiler feedwater and oceanography to determine salinity and TDS.pH / <strong>Co</strong>nductivity MetersSpecificationsTemperature Range: 0 to 150°CTemperature Resolution: 0.1°CTemperature Accuracy: ± 0.2°CDisplay: 20 x 2 line back-lit LCDKeyboard: Aphanumeric splash water-proof polyester soft keysOutput: 1 – Parallel Port for Printer, 1 – RS232C for PCEnvironmental Operating Temperature: Ambient to 45°CRelative Humidity: 5 to 90% non-condensingElectrical Requirements:115V 60Hz230V 50HzDimensions wxdxh,in.(cm)12x8.7x27.6 (30.5x22x70)Net Weight: 4.85 lbs (2.2kg)Catalog No.K90601K90691K90602K90692K90603K90693Ordering InformationpH Meter, 115V 60HzpH Meter, 230V 50Hz<strong>Co</strong>nductivity Meter, 115V 60Hz<strong>Co</strong>nductivity Meter, 230V 50HzpH / <strong>Co</strong>nductivity Meter, 115V 60HzpH / <strong>Co</strong>nductivity Meter, 230V 50Hz74
Automatic Titration<strong>Test</strong> MethodFor determination of Total Acid Number (TAN), Total Base Number (TBN),Mercaptan Sulfur and Karl Fischer Water <strong>Co</strong>ntent of petroleum products,lubricants and transformer insulating oils. Titration is the fundamentalchemical analysis procedure whereby the concentration of a chemicalsubstance in solution is determined by reacting it with a measured amountof another chemical. The Auto titrator performs this analysis using a motordriven dispenser, stirred reaction vessel and electrodes which sense thecompletion of reaction by measuring the potential difference between twoelectrodes. Automatic Titration increases accuracy, repeatability andreproducibility as well as minimizing errors in calculation anddocumentation.Automatic TitratorThe Automatic Titrator is capable of performing a wide range of Titrations:• Acid-base or aqueous titration• Redox titration• <strong>Co</strong>mplexometric titration or EDTA titration• Blank titration• Silver Assay titrations• Non-aqueous titration• Argentometric or Precipitation titration• Voltametric / KF Titration• Back titrationThe Automatic Titrator is provided with two-point auto calibration andstandardization (zero offset). The instrument is capable of displaying pH andmV of the sample, with temperature compensation. The Automatic Titrator canaccept a variety of electrodes to cater to various applications in different fields.The liquid path is comprised of Teflon tubing, a Teflon lined valve and gas tightburette with a Teflon plunger head. It creates a chemically inert system for anysensitive analysis. The instrument is supplied with high speed vortex stirrerwith digital speed indication. This specially designed stirrer provides excellenthomogenous mixing of samples. An optional magnetic stirrer is also available.Ordering InformationCatalog No.K90500 Automatic Potentiometric Titrator, 115V, 60HzK90590 Automatic Potentiometric Titrator, 230V, 50HzAccessoriesK90500-1 Karl Fischer Titrator Burette AssemblyK90500-2 Filter Desiccant Dryer TubeK90500-3 Magnetic Stirrer with Holding RingK90500-4 Magnetic Stirrer with Electrode ArmK90500-5 Vessel Heating / <strong>Co</strong>oling AccessoryK90500-6 pH CheckerK90500 Automatic Potentiometric TitratorSpecifications<strong>Co</strong>nforms to the Specifications of:ASTM D664, D2896, D3227, D4739Principle: Volume determination by equivalence point, end point or pH STAT.<strong>Co</strong>ntrol: Microcontroller basedmV range: ± 3200 mV.Accuracy: ± 0.1 mV (± 0.0016 pH).Amplifier input impedance: > 10 ohmsBurette Resolution: 1/5000 for 5 ml, 1/10000 for 10 ml, 1/5000 for 25 ml.Filling time: Less than 20 secondsKeyboard: Alphanumeric splash waterproof polyester soft keys.Display: 40 x 2 line back lighted liquid crystal display (LCD).Titration Head: Manual stand with swiveling arm.Stirrer System: Microcontroller based variable speed, high torque vortexstirrer with digital indication. (Magnetic Stirrer optional)Sensors:Electrodes for Potentiometric titration - (pH, Ion, Redox, Argentometric).a) Any combination electrode. b) Differential Electrode System comprisingsensing (Indicator) Electrode with BNC <strong>Co</strong>nnector and Reference Electrodewith 4mm Banana <strong>Co</strong>nnector.Electrode for KF/Voltametric titration with BNC/TNC <strong>Co</strong>nnectors.Temperature sensor (PRT/PT100)Calibration: 3-point Calibration with user entered buffer valuesand standardization with 7 pH buffer.End Point detection: a) Potentiometric b) Voltametric c) Thermometricand Photometric.Cut-off criteria: a) Volume b) End point c) mV/pH.Methods:Titrations:a) Acid base b) Nonaqueous c) Redox d) Preciptiatione) <strong>Co</strong>mplexometric f) back titrationKF titration (Optional)Results: a) Molarity b) % Assay(wt), c) % volume (ml) d) ppm e) mg/lf)mg/g g)g/l h) meq/l i) mol/kg j) TAN and TBN for oil samples.Method Storage: 50 methods with parameters.Titrant Molarity storage: 20 valuesInput/Output Peripheral Interface:(a) Parallel Port: 1 - for printer(b) Serial Port: 2 - for Balance & PCElectrical Requirements:115V, 60Hz230V, 50Hz75